Instruction manual

Reassigning Fixtures
This section describes how to reassign
a fixture which is already assigned.
1. Select the Assign Fixtures option
from the Desk Setup screen.
Press the ENTER key. The
Assign Fixture screen is displayed
on the LCD.
2. Use the + and - keys or FIXTURE
SELECTION buttons on the front
panel to select an assigned
fixture. For example:
ASSIGN FIX:< 8 >
<High End >
<Cyberlight (M1) >
[ASSIGN] {EXIT}
3. Press the down arrow key once to
move the cursor to the fixture list
field (lines 2 and 3 on the LCD):
ASSIGN FIX:< 8 >
<High End >
<Cyberlight (M1) >
[ASSIGN] {EXIT}
4. Use the + and - keys to move
through the fixture list and select
a different fixture type. (To
reassign the fixture to a type on
floppy disk see page 6-5).
As soon as the fixture type is
changed, an ‘M’ is displayed next
to the fixture number:
ASSIGN FIX:< 8M>
<Martin >
<MAC 500 (Mode 4) >
[ASSIGN] {EXIT}
5. To assign the new fixture type,
press the down arrow key to
select the Assign button, then
press the ENTER key.
The selected fixture type is
assigned to the fixture, the ‘M’ is
removed from the fixture number,
and the flashing cursor returns to
the fixture number field:
ASSIGN FIX:< 8 >
<Martin >
<MAC 500 (Mode 4) >
[ASSIGN] {EXIT}
Unassigning Fixtures
This section describes how to unassign
(or clear) a fixture which is assigned.
1. Select the Assign Fixtures option
from the Desk Setup screen.
Press the ENTER key. The
Assign Fixture screen is displayed
on the LCD.
ASSIGN FIX:< 8 >
<Martin >
<MAC 500 (Mode 4) >
[ASSIGN] {EXIT}
2. Use the + and - keys or FIXTURE
SELECTION buttons on the front
panel to select the fixture to be
unassigned.
3. Press the CLEAR button on the
front panel.
Or
Press the down arrow key to
move the cursor to the fixture list
field. Use the + or - keys to select
the ‘blank’ fixture type, then press
the ENTER key.
The fixture will be unassigned
(cleared) and the LCD show the
following:
ASSIGN FIX:< 8*>
< >
< >
[ASSIGN] {EXIT}
Viewing Fixture Assignments
This section describes how to view the
current fixture assignments.
1. Select the Assign Fixtures option
from the Desk Setup screen.
Press the ENTER key. The
Assign Fixture screen is displayed
on the LCD.
ASSIGN FIX:< 8 >
<Martin >
<MAC 500 (Mode 4) >
[ASSIGN] {EXIT}
2. Use the + and - keys or the
FIXTURE SELECTION buttons on
the front panel to select the
required fixture.
Exit Assign Fixtures
This section describes how to exit the
Assign Fixture screen.
1. Use the arrow keys to select the
EXIT button on the LCD:
ASSIGN FIX:< 8 >
<Martin >
<MAC 500 (Mode 4) >
[ASSIGN] {EXIT}
2. Press the ENTER key on the front
panel. The LCD returns to the
Desk Setup screen.
NOTES
Reassigning Fixtures
A fixture can also be reassigned in two stages
by first unassigning it (see page 6-6 ) and
then assigning it (see pages 6-4 and 6-5).
Warning - Reassigning a fixture will affect
the data in programmed memories and
submasters. The original fixture channel data
is removed and replaced by the default values
for each parameter in the new fixture type,
with the exception of the brightness
parameters which are set to zero.
Unassigning Fixtures
If a fixture type loaded from floppy disk is no
longer assigned to any fixture, then the
fixture type is removed from the fixture list.
6 - 6 Frog Series 73-750-00 Issue 6
Super User