manual

19
Troubleshooting
TROUBLESHOOTING PROCEDURES
Issue Cause What to do
After installation,
the unit doesn’t
ZRUN
1. The power source is not turned ON.  0DNHVXUHWKHFLUFXLWEUHDNHUDQGWKHXQLW¶V
power is ON.
 7KHSRZHUOLQHDQGWKHFDEOHORFNLQJFRQQHFWRU
is not connecting properly.
 &KHFNWKHSRZHUFRQQHFWLRQZLWKWKHXQLWLV
connected properly.
3. The switch board or control board wirings are
disconnected.
 0DNHVXUHWKHZLULQJVDWWKHVZLWFKERDUGDQG
control board are connected properly.
4. The switch board or control board is defective. 4. Change the switch board or control board.
/LJKWZRUNVEXW
blower is not
turning.
1. The blower is defective, possibly seized. 1. Change the blower.
2. The thermally protected system detects if the
blower is too hot to operate and shuts the blower
down.
2. The blower will function properly after the
thermally protected system cool down.
3. Damaged capacitor. 3. Change the capacitor.
4. The switch board or control board is defective. 4. Change defective part.
The speed levels
of the blower
sound the same.
1. Using the wrong size or type of ducting. 1. Change the duct size to at least 6” round or
higher and change the duct type to rigid metal
UDWKHUWKDQÀH[DEOH
The unit is
vibrating.
1. The blower is not secured in place. 1. Tighten the blower in place.
2. Damaged blower wheel. 2. Replace the blower.
3. The hood is not secured in place.  &KHFNWKHLQVWDOODWLRQRIWKHKRRG
The blower is
ZRUNLQJEXWWKH
lights are not.
1. Defective LED bulb. 1. Change the LED bulb.
2. The LED wire connection to the control board is
disconnected.
&KHFNWKH/('ZLUHFRQQHFWLRQDWWKHFRQWURO
board.
3. The LED bulb connector is disconnected. &KHFNWKH/('EXOEFRQQHFWRU
The unit turns on
by itself.
$VSRWOLJKWRUNLWFKHQODPSLVVKLQLQJGLUHFWO\
onto the switch controls.
1. The switch controls are light sensative. A
direct light source onto the switch controls
may disrupt switch functions.
The hood is
not venting out
properly.
1. The hood might be hanging to high from the
FRRNWRS
 $GMXVWWKHGLVWDQFHEHWZHHQWKHFRRNWRSDQG
the bottom of the hood within 26” and 34”
range.
2. The wind from the opened windows or opened
GRRUVLQWKHVXUURXQGLQJDUHDDUHDႇHFWLQJWKH
ventilation of the hood.
2. Close all the windows and doors to eliminate
WKHRXWVLGHZLQGÀRZ
 %ORFNDJHLQWKHGXFWRSHQLQJRUGXFWZRUN  5HPRYHDOOWKHEORFNLQJIURPWKHGXFWZRUNRU
duct opening.
4. The direction of duct opening is against the wind. 4. Adjust the duct opening direction.
5. Using the wrong size of ducting. 5. Change the ducting to at least 6” or higher.
Mesh Filter is
vibrating.
 0HVK¿OWHULVORRVH  &KDQJHWKHPHVK¿OWHU