www.zephyronline.com RO I! II_J A ZRA-E30AS ZRA-E36AS ZRO-E30AS ZRO-E36AS C iim m m 1/) C m C (3 ZRA-E3OAS ZRA-E36A S Voltage 120V 60Hz Power Consumption Total: 180W Lamp: Max 50W x2 Fan: 80W ZRO-E30A ZRO-E36A Voltage 120V 60Hz Power Consumption Total: 400W Lamp: Max 50W x2 Fan: 300W Model number: Serial number: Dealer Name: Date of Purchase: APR07.
. Illl O0 . . _ 0 READ AND SAVETHESE INSTRUCTIONS WARNINGTO REDUCE THE RISK OF FIRE, ELECTRIC PERSONS, OBSERVE THE FOLLOWING: a ) Use this unit only in the manner contact the manufacturer. b) Before servicing or cleaning service disconnecting means to When the service disconnecting prominent warning device, such "CAUTION SHOCK, OR INJURY TO intended by the manufacturer.If you have questions, unit, switch power off at service panel and lock the prevent power from being switched on accidentally.
c)Clean ventilating fansfrequently. Grease should notbeallowed toaccumulate onfanorfilter. d)Useproper pansize.Always usecookware appropriate forthesizeofthesurface element. WARNINGTOREDUCE THERISK OFINJURY TOPERSONS INTHEEVENT OFARANGE TOP GREASE FIRE, OBSERVE THEFOLLOWINGa; a) SMOTHER FLAMES withaclose-fitting lid,cookie sheet, ormetal tray, then turnofftheburner. BECAREFUL TOPREVENT BURNS. Iftheflames donotgoout immediately, EVACUATE ANDCALL THEFIRE DEPARTMENT.
INSTALLATION MOUNT HEIGHTS & CLEARANCE Minimum mount height between range top to hood bottom should be no less than 28". IIIIIIIIIIIIIII i Maximum mount height should be no higher than 36". 29 - 48' It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire hazi rain ard; while hoods mounted too high will be hard to reach and will loose its performance 28'-max and efficiency.
INSTALLATION DUCTING NEVERexhaust air or terminate duct work into spaces between walls, crawl spaces, ceilings, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certified silver tape or duct tape.
INSTALLATION SPECIFICATIONS q E 0 ! ..... 29-15/I6", 35-7/I6" ELECTRICAL All electrical work must be performed by a qualified similar technical know how and background. electrician or person with For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
INSTALLATION INSTALLATION Mounting the Range Hood C/L 1, Measure from range top to hood bottom (28" rain) Level and mark line A, _'_Duct Cover Bracket 2, Plum and mark center line. 3. Mark mounting ( 12-5/32 " from height line B. line A) 4. Mark mounting spread from C/L (12-19/32") 5, Fasten screws to wall (see below) as marked (line B). 6. Hange hood onto screws and tighten (fig.
INSTALLATION DUCTLESS CONVERSION Ductless conversion installed. Fumes then When and is intended converted, exhaust purified and from for applications the hood cooking re-circulated are drawn back where functions within an exhaust as a recirculating and the filtered duct hood work rather by a set of optional is not possible to be than an exhaust hood. carbon filters. The air is home.
CONTROLS & FEATURES CONTROLS& FEATURES O Blower On/O':f _t III L ghts On!Off 0/I Blower Speed Selection Blower On/Off The blower will be switched on or off by pressing: 0 Blower Speed Selection Select one of three speed levels by pressing: 000 I II III Lights On/Off Switch lights on and off by pressing: 0/I Page 6
MAINTENANCE CLEANING Surface Maintenance: Clean periodically or abrasive damage hot soapy water and a clean cloth. or steel wool/scouring soil use a liquid cleaning clean cotton you may use non abrasive cloth stainless luser and grain. steel polish/cleaners to Always scrub lightly with a and with the grain. Filters The metal filters fitted intended from Do not use corrosive will scratch and degreaser. polish and buff out the stainless Metal pads which the surface.
MAINTENANCE LIGHTS Replacing Light Bulbs Make sure all power is turned bulbs are not hot. off and Remove by turning clockwise. bulb counter If bulbs are difficult to turn due to prolonged use, firmly attach a glass suction cup approx, the diameter of the bulb and turn. Replacement bulbs are available at specialty lighting stores. Purchase type GU-IO 50W halogen bulbs. Or to order bulbs, please call our service center:888-880-8368or online parts store: www.zephyronline.
