Use, Care, and Installation Guide www.zephyronline.com Monsoon I AK9228AS AK9234AS Model number: Serial Number: Date of Purchase: Sales Dealer: JAN12.
www.zephyronline.
LIST OF MATERIALS ................................................................. 4 INSTALLATION Ducting Calculation Sheet ....................................... Mounting Height & Clearance................................ Ducting Options ........................................................... Specifications ............................................................... Electrical ......................................................................... Cabinet Preparation & Installation ............
www.zephyronline.com Important Safety Notice READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer. b.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. NOT FOR USE OVER AN OUTDOOR GRILL CAUTION To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers and loose clothing.
List of Materials www.zephyronline.
Equivalent number length x used = Duct pieces Total Total 3-1/ 4” x 10” 1 Ft. Rect., straight x( ) = Ft. 6” Round 30 Ft. wall cap with damper x( ) = Ft. 6” Round, straight 1 Ft. x( ) = Ft. 6” Round, roof cap x( ) = Ft. 7”-10” Round, 1 Ft. x( ) = Ft. 6” round to 1 Ft. 3-1/ 4” x 10” rect. transition x( ) = Ft. 3-1/ 4” x 10” 15 Ft. Rect.90 0 elbow x( ) = Ft. x( ) = Ft. 3-1/ 4” x 10” 9 Ft. Rect.45 0 elbow x( ) = Ft. 6” round to 16 Ft. 3-1/ 4” x 10” rect.
Installation – Mounting Height & Clearance www.zephyronline.com Minimum mount height between range top to hood bottom should be no less than 26”. Maximum mount height should be no higher than 36”. It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire hazard; while hoods mounted too high will be hard to reach and will lose its performance and efficiency.
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use single wall rigid metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape. Some Ducting Options side wall cap w/ gravity damper side wall cap w/ gravity damper Soffit or crawl space 8” round or 3-1/4”x10” rect.
” 12 22 -3/ 8” ,2 8- 3/8 ” 3” 12” 28 - 3/ 8” ,3 4- 3/8 ” 19 ” 1 /4 (28”)9-1/4” (34“)12-1/4” elec. k/o Ø 73 C/L Top View (28”) 9-1/4” (34“)12-1/4” C/L 9-7/8” Back View 8 5-1/2” 3-1/4” 7-3/4” /4 ” 2” (28”)14-1/4” (34“)17-1/4” 1-1/2” 5-5/8” 3/4 View 10-3/4” Installation – Specifications www.zephyronline.
WARNING All Electrical work must be performed by qualified electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
! CAUTION: At least two installers are required due to the weight and size of the insert. If possible, power up and test all functions prior to installation. 1. Remove all packing materials and protective film prior to installation. Use caution during installation to prevent scratches or damage to the stainless steel. 2. Cut out an opening in the bottom of the cabinet by following the dimensions in FIG. 1.
1 1 2 2 2. Remove grease tray by: 1) Pulling up on tray to release from bottom panel. 2) Lifting tray out of insert body. 1. Remove baffle filters by: 1) Pulling filter toward front of insert. 2) Pivoting rear of filter down. 1 Bottom Panel Screws 2 Locking Tabs 4. Remove bottom panel by: 1) Removing (2) screws from left and right sides of bottom panel. 2) Pulling bottom panel toward front of insert to release from locking tabs. 3.
Installation – Horizontal Ducting Preparation www.zephyronline.com 1 1 1 2 2 2. Remove grease tray by: 1) Pulling up on tray to release from bottom panel. 2) Lifting tray out of insert body. 1. Remove baffle filters by: 1) Pulling filter toward front of insert. 2) Pivoting rear of filter down. 1 Bottom Panel Screws 2 Locking Tabs 4. Remove bottom panel by: 1) Removing (2) screws from left and right sides of bottom panel. 2) Pulling bottom panel toward front of insert to release from locking tabs.
A Round ducting B A C B C 7. Using a flat head screwdriver, remove 8” round or 3 1/4”x10” rect. knock-out plates at the back of the insert. 8. Remove knock-outs A and B for rectangular ducting. Remove knock outs B and C for round ducting. At this point, install the insert into the cabinet by following the steps on Page 10, Step 4. After insert installation, continue to page 14. 9. Place top rectangular cover plate over opening on top of the insert.
Installation – Horizontal Ducting Preparation www.zephyronline.com 10. (Rectangular Ducting) From inside the insert, push 3-1/4” x 10” rectangular adaptor through the back knock-out and secure to interior back wall of insert with (8) M4 x 6mm screws. 10. (Round Ducting) From inside the insert, push 8” round adaptor through the back knock-out and secure to interior back wall of insert with (4) M4 x 6mm screws. 2 1 11.
Display (speed level, delay off, filter clean) Lights On/Dim/Off Adjust 6 Speed Levels 5 Min Delay Off 1. Blower On/Off By pressing the blower is switched on and off. When switched on, the blower starts up on speed level 1. 2. Speed Selection The 6 speed levels are selected by pressing selected. to decrease and to increase speed levels. The display indicates levels 3. Delay Off This feature is used for programmed shut down of blower 5 minutes after the function is activated.
Features & Controls – Touch Controls www.zephyronline.com Baffle Filter Clean Reminder Aa set of baffle filters are fitted by the factory, these baffle filters are intended to filter out residue from cooking. The filters need not be replaced on a regular basis but are required to be kept clean. The BaffleFilter Clean reminder function in the microprocessor will automatically indicate by a flashing F when the baffle filters need to be cleaned after every 30 hours of use.
SYNCHRONIZATION: To create a unique link between your insert and remote control please follow these steps: 1. With insert off, press and hold the “lights” button on the insert until the letter “F” shows on the display screen. 2. Press the “lights” button on the remote, the lights on the insert will turn on and synchronization is complete.
Maintenance – Cleaning and Installing Filters www.zephyronline.com SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/ scoring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners. For heavier soil use liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/ cleaners, to polish and buff out the stainless luster and grain.
CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and falls out. If bulbs are difficult to turn due to prolonged use, firmly attach the glass suction cup provided to the bulb or use a rubber/latex glove and turn counter clockwise.
Troubleshooting www.zephyronline.com TROUBLESHOOTING PROCEDURES FOR MONSOON I Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting properly. 2. Check the power connection with the unit is connected properly. 3. The switch board and control board wires are disconnected. 3.
2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 2 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475 500 525 550 575 600 625 650 675 700 725 750 Flow rate (CFM) Model: AK9228AS AK9234AS Voltage 120V 60Hz Power consumption Total: Max.480W @3.9A Lamp: Max.
List of Parts and Accessories www.zephyronline.com DESCRIPTION PART # Replacement Parts Light Bulb MR16 (GU10) 35W (each) Z0B-0023 AK9228AS / AK9234AS Baffle Filter, Large (each) 50210013 AK9234AS Baffle Filter, Small (each) 50210017 RF Remote Control 14000005 To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.
STAPLE YOUR RECEIPT HERE Proof of the original purchase date is needed to obtain service under warranty Limited Warranty TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: 1-888-880-8368 Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or workmanship as follows: Three Year Limited Warranty
