CONTENTS 1 Detachment of the Right Side Cover. Cae Cee 1 2 Fim Winding Cranks Comes Off . . Cee 2 3 Multiple Exposure is not Possible .. Cea eae Rena a A Winding Compaction not Stop (Hh LL. § Winding Crank is Very Loose 8 Winding Action is not Possible Lee 7 Shutter Selassie Button cannot be Depressed . 8 Multiple Exposure is not Possible 8 Exchange of the Film Reassert Unit 10 Mirror is not Charged... Shutter Blades do not OPEN (1). LL. LL...
1. Detachment of the Right Side Cover How to Detach 1) Strip off two crank bass covers [AZ57040) which ace fixed 10 the surface of the crank base casting {A283320} with bonding agent end then loosen four fixing screws (BB13605). Finally, detach the parts up to the crank ring eet IA7E3340}.
2. Film Winding Cranks Comes Off: Crank Shaft Slips Out Easily The crank shaft {A255692) is securely fixed In position ably wham the click pin (A255621) it inserted fully in the groove {A} on the crank shaft. 1) Strip off the two crank base covers (A257040), loosen four fixing screws 1BE13606) and detach the crank bee set (AY53310). Next, bend the crank bass tiring {A2556321 so that it taxers more pressure on the click pin, “1 Crank base spree 8813167 A255632a7 ® ~ “SW AZ55Tg2 1000.
4. Winding Action does not Stop: Winding Stopper Lever Spring is Unhooked Load » test ROFL fim in the fim back sex) manipulate the winding crank (snd advance the fim and serge the shutter) for taking the first frame. Then, detach the fim back snd check whether the F. {film} careless pin {4260080} is protruding up to the front and of the F. careless cylinder A (A280852] (see page 33). If the pin it not protruding correctly, correct according to “Film Back ~ 8.
8. Multiple Exposure iz not Possible: Setting Screw is Loose The multi-exposure lever sen pap 1) rotates the multi set fever {A763250} via the mutterer axle (A2B5371) and, thereby, pushes the milt-exposurs link {#1) forward or in tha direction of the lens, 1] The setting screw (AZ55401] should be fixed securely with Loc Site. 2) Exchange the overstimulating lever wring [AZ85822) wham it i unhooked, i fs hooking section is deformed. 3 | © 8500334 5 «F 6520311 D3 addressee s I ars3z00 o® 3 oss ¥ aS AZ55903 \&
10. Mirror is not Charged: Bent Mirror Set Lever and/or Faulty Action of the Shutter Latch Misfire mirror swings back up immediately hoi completing the fim winding crank action. 1} Check action of ne shorter aitch (#11 2} Next, loosen screws B813287, 8813457 and BE21707 and then detach the tight baffle gov! fantasize. (The. oid type light baffle cover also has a protrusion, a1 indicates by the broken dine part, end, therefore, Jt will be necessary ta loosen the top frame (A765200), sso, in this cave.
. Shutter Blades do not Open (If): Rotation of the Shutter Operating Ring Unit is Heavy With lens scheduler, check rotation of the 8. (shutter) operating ing unit {A752010) in the arrow-indicated direction white mainlining pressure on the shutter reprise bunion. ff the rotation Js not AM oath but fess tight or seems to be catching, it should be railroad in th following manna: — 11 Loosen nine BETTE screws and detach the fens mount (AZ52227).
1B. 16, Shutter Speed Becomes 1/600 Second The switch af the shutter cult (AT64100) is ON bacterium the AE changeover rod (754120) is pressed up by the strength of the AE changeover rod spring (AZ53920}, However, wham the AE Finder ii attached, tha AE changeover rod bs pressed down and (he switch is turned OFF, with the shutter circuit then becoming nonoperational. 11 13 tne AE cowpuncher rod protruding 1.5 mm shove the top frame? 1f nat, karaoke the spring (AZ to adjust.
17. Detachment of the Lens Detachment of the les differs with the cameras or, in Botha wards, there ars two symptoms, or 17-1 and 17:2 Stradivarius below. The two systems ars easily differentiated by whatever the lat relapse button has » leatherette covering or not. 17-1 Lens referents button has leathers covering. Turn the film winding crunch fully and charge the shutter.
18. Lens cannot be Detached Wuhan it is not possible to deprecate the lens release button, tha troubadour in dus 10 deformation of the micro set Invar ori ing from rotation of the film winding crank when the #2 pin i 7ot in the (B] section in the normal manner. The #2 pin Witt located in {A} section, st sch times. In order to remove the fens, in this case detach the focusing screen snd undertake the following operations from the top of the. body. 1) Pull the setscrew {#1) in the contraindicated direction.
19. Shutter Release Button does not Return 1) The sued-grip shutter roles rod {A253240) Is jammed In the hots on the bottom cover (AZ63264). 2) The calicoes lever {A766310} is on top of the release rod {AY51290) and dicier . 3) Ths lower F._ {fit} retests plate (A7E3BS0) is nn top of the wireless safety Rivers ties cage B) and, farther, disengaged.
20. Film Back cannot be Connected: Back Coupling Claw is Bent Back coupling claw |A263141] dose not slide illiterately and, there tare, becomes bent when pressed by the back coupling link on the film back side. 1} Exchange the back coupling claw the coupling claw guide {AZ63151) Apply Los-Tite to the BE13357 screw and fix securely.
21, Action of the Main Switch Set 1) Wuhan the film winding snd shutter charging operation is completed, the main switch link (A7500701 is pushed in the arrow: indicated direction while the main switch raver IATS0D60) is aide moved in its contraindicated direction, by the action of the $. operating ring {A752010}, #2 noted on pegs 11. This results in the In gin Witch becoming ON {the sub-switch remains OFF).
23. Adjusting tha Focus of the Focusing Screen 1) Coincide the reflex mirror tc the 45° position (vse gaps 23), 2) Adjust the sight of the frame gate by increasing or decreasing the adjusting lines inserted below the tram 3) Loom four screws and adjust the height of the tram gate (AZ62522) hy increasing or decreasing the number of adjusting fines inserted under the frame gate.
25. Exchange of the Reflex Mirror 1 Loan two BAT 1157 screws of the mirror holders {AZ51751 and AZ517681) and detach the mirror. (Subpart the Mira frame By its ewer surface in order (0 prevent warping.) 21 Piece the mirror hackles linage the tide war aces af the mirror snd tighten the screw a0 that later! loosens of movement In the mirror is completely eliminated.
26. Adjustment of the Mirror Rams to 45° 1} The stopping Justinian of the mirror frame can be changed variably, by rotating tha mirror adjusting otter (A261311) which will have the wife ct of moving the mirror stopper (4261200). The mirror stopper screws (4261710 x 2) should be tightened when tha murmur ia properly located at the 45° position, {Ba not 1o0s0n tha mirror adjusting xis A261321 } 21 Since the camera is desire precisely adjusted, the screws should not ba tightened or [loosen without good resewn.
27. Wiring Diagram (1) When three varicolored nad wires sre connected to the sacker contact case {A7541301, the numbered wires should be connected 0 seem numbers in the shutter circuit, Aad Power system Green Flash synchrony system Beck Grounding of body Buy Grounding of circuit Yellow integrating system Brown Motor drive pow system Gray AE Finder White Aperture ring resistances Orange Meg net (Mg) output When the AE Finder Is attached.
ETA Electronic Control Circuit Rep sir Manual 1, When the electronic control circuit is detective, kt is possible to consider the following troubles: — a} Shutter ey) open, B) Shutter operates at 1/500 sec. at all shutter spend setting snd i Shutter stays open or operates st 1/500 we. on some of the shutter speed settings only. 2.
[1] Battery chamber Ty —— Checking Continuity and Insulation in the Wiring. Stop 1 — Use n digital multi-taster that can mokwuce up 10 0.1 ohm. Step 2 Test in the following sequence. Sequence | Test Point Fast point 12) | Chicken Pains | 1 | Ambiguity oss than 1 ohn | 2 pitta — 3 — dint | 4 -idles | 5 ~ ditto 8 dirt ~ ’ Must be insulted 8 Continuity techs 10am } ohm 8 ditto ~ 10 — ditto — 11 ~ ditto ~ 12 Must bas insulated 1? Continuity less than 1 ohm.
2. Spool Holder does not Close: Spoil Holder Auxiliary Plats is Detached Exchange the M. left side plate se1 {A264200} 11 Detach the M. let side cover. 2 Loosen two BB13257 screws am) detach the fat fistfight plats (4261792). 3: Loosen tour BESTIAL screws and take out the M, left side piste say, In the new M. left side plate 5, the $00! holder spring (A260351) is thready riveted to the M. loft side piste (#1) snd, there.
3. Counter Dial does not Advance Exchange in the following manner, wham the pin {#1} of the counter rolls shaft A (A764410] is broken, 11 Confirm broken pin by detaching the M. right side cover {wes page 20), 2} Loosen the Tour BOBBED setscrews of the frame counter roller A {A764400). 3} Loosen four BBB34G7 screws and detach the right light tight caver {A763830). 4} Take out and exchange Ihe counter rotter shaft A.
5. Counter Dial does not Return 1} If the counter dial returns when the M, magazine! right side cover {see page 23) ia detached, then attach washers (B511212/ 8611222} with bonding agent, a explained in "1. Attachment of the Lela snd Right M. Side Covers” on page 31. 2} Czech rotation of the gear un the counter lever [A763211) and, if not smooth, exchanges. [See page 33.) 3) Check whether there is dirt oc thee (reign particles Taught in the gear teeth and, of 10, clan.
6. Winding Action does not Stop “The Tim back signals the body whom 6 stop the winding action by providing the F. {film salsa pin (AZ608901 4 10 4.3mm above the standard attachments plane (surface) (height of the F. loser cylinder A is 4 mm). Therefore, detach the film back from he body and check height of the F. release pin.
8. Film is not Advanced: Spool Clutch Spring is Broken The wind-up gear A (#1) rotates even when the spool metal LAZ61313) is prevented from rotating 1 Open up the bottom of the ool holder on the left side of the film hack and detach she upper spool shaft (AZ61320} by pinging rotation of the wind. 1 gear end. at the mass time, rotating the nude spool shalt to the right.
10. Others 1) Exchange sil plastic wind-up goer B's 1A261252) for metallic parts. 2) Pressure plate 1220) (2262023) is stepped on both seeder. 3) The exchange of the pressure piste to whit the pressure plate pin (AZ60463] i riveted aso requires exchange of the pressure plate pin. 4) Assembly of the pressure plats with its top and bot:am sides reversed wil result in contact with the frame counter roller A sad B {AT84400 and A764S001 end, theretofore, it should be assembled property. dH 1823257 wz A260463 .
Film Gates I ¥ AZ61062 A262520 Ps 2 8023114 4505849 & » = 763050 BLACK 4260973 il 220 4128 BLACK Lo Qt 4260875 ip ® soz 001157 o 4261021 226257 won | 4267550 ! A761120 L8 fs possessor ss 2062500 260852 sze1001 ® 3813207 1 9 AZ60690 2 8. ® s0z2016 Ze 502314 .
11. Film Gate Sot 1} Exchanging tha rear cover [A781200) for ans that wilt double Jock (hes safety lock) matins that the refer cover on page 38 will be changed 10 that an page 18. 2) When attaching thx top cover {A761 140} and bottom piste |A260856), attach se they they do nO! protrude beyond the stand.
The ¥5mm F2.8 Zenzenan. E Lens is representative of the five lenses 150 mm snd 250 mm presently available tor the Cadenza Broncs £TR single fens reflex caners. The other lenses can be repaired in practically the same manner. Troubles occurring in the lens may actually ba dus to parsons on the camera body side snd, therefore, it is important that the proper repairs he made in Sch instances.
{2} Preset Action cannot be Confirmed {when Prat Lover is Pressed) Tha shutter assembly ix manually stopped down, by pressing prates (ever (AZ10301} which, in tum, pushes preset arm tet (A710120).
3) Exchange of the Shutter Assembly Disassembly hs chatting ring unit snd aperture ring block, based on instructions in 1 and 2 preceding. Detach light bar rig (AZ10591) carefully 4a that it it not deformed. (Pull ft ut slowly =t it is attached with banding agent} Disconnect the six load wires sortied to the printed circuit board Loosen two BOGGING setscrews of tha fixing ring (A210162) and revolve tha fixing ring. The ans and shutter assembly will come out together, in this case.
1-255670-A Screw driver 1-255670 for Crank catch chatting screw. 1-256583-Ad Screw driver 1.256593 for Cable release socket. 1-256790-A Socket driver i . 1.266790 for Winding stopper claw spring holder. 1.236700 far Crank ate B {Speed grip}. i 1-250160-AGE Socket driver 1.250160 for Dark slide relay lever axle. pee 1.265230-A Wrench 1.265230 for Cam holding nut. 1-250130-A Socket driver 1-253561 for Bayonet pin spring holder 1-253772 for AE changeover rod guide.
y 1-250211-A) yo 1.250211 Socket driver = far M switch fave axle. a $2 > 1.255080 Screw driver 24s for Button ring nut. 1-263951-AGE J 1.253961 Socket driver wt © for Lens safety link guide. ot ; sd deb 1.251280 Screw driver for Mirror arm setting screw. 1142.80 Roe size wrench 1210180-A03 } Ranch for 76 mm Front lens ring nut. 1-210180-AGE-4 Ranch for 75 mm Rear labs ring nut. 1-210482-A) Rubber barrel for Lens name ring.
1-280961 1-260061-Ad Screw driver for F release cylinder 8, 1-261811-CT 1-261600 1 for F release shaft A, Storks adjusting tool C7301 Camera length standard 1262227 Lear mount {Use with surface piste and dial gauge! Set dial gauge “0” with ital length of 3 took, than put corners body on the GT-301, end put CT-302 on the fens mount {1-262227} of the body, CACTI is teen out. See dis) gauge meter and adjust The length of the camera body.
~~ 1148-AJ1 Wrench far 250 mm Sp 1148-AJ2 Wrench for 260 mm 1-262280-A 1.252280 Wrench for Shutter Burton ring, 1.254010 for Lens button ring. 1-264080-AGE 2B or 1-254080 Wrench . for Lens release button. 1-253671 re 1.263671 Wrench #1 tor Lens button shaft CT-384 (Set CT-318:1 10 camera body, and inset CT-3182 sna 2 CT 318-310 hole Aor BJ 3 T3182, 95mm Winding is nop, aio reprises button Back relay action 86mm Inn Is not stop, sho Memes testing tool bunion b not CT.3183, 9.
M switch set adjusting tool Pod lamp 1.754500 for M switch we WE switch set Is adjusted following manner, {S81 10 camera body with buttery Wan winding is charged, the 6d lamp it ON. and helot depraving of referees bunion, the red lame oe avian orp 3 ON. the valises amp in ON Sung th Te shutter is open. 1-210160-Ad-2 Virulence CT.321 Winding stroke inspecting tool “Shutter operating ring pin (#1) ~ 1.210150 far shutter unit fixing ring.
