EB7001 115 40 00-73 (010) G B OWNER’S MANUAL BLOWER EB7001 GB-1
EB7001 SAFETY FIRST Contents Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
EB7001 2. Specification MODEL EB7001 Dimensions (LxWxH)** Dry weight* Fuel tank capacity Engine type mm kg liter Displacement Air filter Carburetor Ignition system Spark plug Muffler Operating engine speed Fuel consumption Air volume* Max. Air velocity* cm3 365x485x495 9.7 2.1 Air-cooled 2-cycle gasoline engine 62.0 2 stage fresh flow filter system Diaphragm, rotary valve type C.D.I. NGK BPM R7A (Noise-proof) Spark arrester equipped 2000 to 7300 1.9 16.5 91 rpm liter/h cu.
EB7001 5. For safe operation WARNING 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4.
EB7001 5. For safe operation 8. The ignition system of your unit produces an electromagnetic field of a very low intensity. This field may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemaker should consult their physician and the pacemaker manufacturer before operating this tool. Limit the amount of time over which the product is to be used continuously to somewhere around 30 ~ 40 minutes per session, and take 10 ~ 20 minutes of rest between work sessions.
EB7001 5. For safe operation WARNING • Check to see if the shock-absorbing rubber mount has become cracked or otherwise damaged. Note that failing to replace this rubber mount when it has become cracked or damaged may cause the engine to come loose from its frame during use, thus resulting in possible serious bodily injury. • If cracked, be sure to replace without delay.
EB7001 engine. Especially never forget to cool down the engine before refueling the machine. 10. In an emergency, pull up the lower portion of both strap buckles to loosen the straps. Move yourself away from the unit. 11. After using blowers and other equipment, CLEAN UP! Dispose of debris in trash receptacles. MAINTENANCE 1. In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals. 2.
EB7001 6. Set up FLEXIBLE HOSE and SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. (2) (3) (1) (1) (2) (3) (4) Flexible hose Swivel joint Clamp (Large) Clamp (Small) (4) NOTE A light lubricant may be used to ease assembly of flexible pipe to blower elbow. CONTROL HANDLE • Set up the control handle to the swivel joint and tighten the screw on the control handle holder.
EB7001 7. Fuel ■ FUEL • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
EB7001 8. Operation STARTING ENGINE 6. Once the engine is running, gradually open the choke if it was set closed, and let the engine run at idle speed for a minute to warm it up. IMPORTANT • Avoid operating the blower with the flexible tube and swivel joint disconnected. That will reduce the cooling air and the engine could be damaged by overheating. 1. Push the primer bulb until fuel flows out in the clear tube. 2. When the engine is cool, close the choke.
EB7001 9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual.
EB7001 9. Maintenance REPLACEMENT PLUG NGK BPMR7A IMPORTANT • Note that using any spark plugs other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged. • To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench. PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup.
EB7001 9. Maintenance 10. Storage HARNESS If the harness is damaged it may break during use, thus causing the product to fall and resulting in personal injury. Follow the instructions below to replace the harness with new one. BEFORE STORING THE BLOWER: 1. Drain a fuel tank and push the primer bulb until it becomes empty of fuel. 2. Remove the spark plug and drop a spoonful of 2-cycle oil into the cylider. Crank the engine several times and install the spark plug. 3.
EB7001 12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug → → → → → → PROBABLE CAUSES incorrect fuel fuel filter is clogged out of normal range spark plug is fouled/wet plug gap is incorrect disconnected Case 2.
