Service manual

17. Treble (Command:r)
G To adjust treble.
You can also adjust treble in the Audio menu.
Transmission
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’. See page 25.
[k][r][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data Min: 0 ~ Max: 64
[r][ ][Set ID][ ][OK][Data][x]
16. PIP Position (Command:q)
G To select sub picture position for PIP.
You can also adjust the sub picture position using
WIN.POSITION on the remote control or in the Special menu.
Transmission
Data 0: Right down on screen
1: Left down on screen
2: Left up on screen
3: Right up on screen
[k][q][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data 0: Right down on screen
1: Left down on screen
2: Left up on screen
3: Right up on screen
[q][ ][Set ID][ ][OK][Data][x]
18. Bass (Command:s)
G To adjust bass.
You can also adjust bass in the Audio menu.
Transmission
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’. See page 25.
[k][s][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data Min: 0 ~ Max: 64
[s][ ][Set ID][ ][OK][Data][x]
19. Balance (Command:t)
G To adjust balance.
You can also adjust balance in the Audio menu.
Transmission
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’. See page 25.
[k][t][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data Min: 0 ~ Max: 64
[t][ ][Set ID][ ][OK][Data][x]
13. Remote Control Lock Mode (Command:m)
G To lock the front panel controls on the monitor
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data 0: Lock off 1: Lock on
Data 0: Lock off 1: Lock on
• If you’re not using the remote control, use this mode.
When main power is on/off, remote control lock is released.
[m][ ][Set ID][ ][OK][Data][x]
14. PIP / Twin (Command:n)
G To control the PIP (Picture In picture).
You can also control the PIP/TWIN using the PIP or Twin
picture button on the remote control or in the Special menu.
Transmission
Data 0: PIP/DW of
1: PIP
2: DW1
3: DW2
Data 0: PIP/DW of
1: PIP
2: DW1
3: DW2
[k][n][ ][Set ID][ ][Data][Cr]
Acknowledgement
[n][ ][Set ID][ ][OK][Data][x]
G To adjust the screen sharpness.
You can also adjust sharpness in the Video menu.
Transmission
11. Sharpness (Command:k)
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping1’. See page 25.
[k][k][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data Min: 0 ~ Max: 64
[k][ ][Set ID][ ][OK][Data][x]
12. OSD Select (Command:l)
G To select OSD (On Screen Display) on/off.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data 0: OSD off 1: OSD on
Data 0: OSD off 1: OSD on
[l][ ][Set ID][ ][OK][Data][x]
15. PIP Size (Command:o)
G To select the PIP picture format.
You can also select the PIP picture format using WIN.SIZE
on the remote control.
Transmission
[k][o][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data 0: 4:3 1: 16:9
Data 0 : 4:3 1: 16:9
[o][ ][Set ID][ ][OK][Data][x]
EXTERNAL CONTROL DEVICE SETUP