Installation Instructions Zip HydroTap ® Filtered Chilled drinking water for commercial kitchens and tea rooms. Affix Model Number Label Here 801525 801525 - Zip HydroTap Installation Instructions - Nov. 2013 - V1.
Index HydroTap Specifications Installation check list .................................................................................................................... 3 General Product Features ............................................................................................................ 4 Important Safety Instructions ....................................................................................................... 5 Warnings and Regulatory Information...............................
Installation checklist Before Installation: A. Read the instructions and check if there is adequate space to mount all of the components. B. Note: Not all fittings are supplied with the appliance kit. Isolation valves are not supplied. C. Check the mains water pressure is between 172 - 700kPa D. Check the water quality to determine if extra filtration will be required. E. Check the appliance rating plate and ensure correct power is available for the appliance. F.
General Product Features Thank you for purchasing a Zip Chilled HydroTap. Please read and follow these instructions carefully to ensure safe operation and trouble free service. If service is required, please call 1800 460 222 What is the Zip HydroTap ? The Chilled Zip HydroTaps are electronically controlled to supply filtered and Chilled drinking water for kitchens and tea rooms.
Important Safety Instructions This manual contains important safety, installation instructions for the Zip HydroTap G4. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Important Safety Instructions WARNINGS 1. 2. 3. 4. 5. 6. 7. 8. 9. The Zip HydroTap unit must be earthed. The resistance of the earth connection from each exposed metal part must be less than 1 ohm. All Installation and service work must be completed by trained and suitably qualified Tradespeople. Faulty operation due to unqualified persons working on this product, or any other Zip product may void warranty coverage. All Plumbing must comply with AS/NZS3500.
Technical Specifications Model Glasses of Chilled Water per Hour C 175 Commercial Models: C = Chilled filtered D = Disabled lever controls, (Order as an option) Note: the standard Glass measurement =200ml Product covered by these instruction: Capacity Chilled (glasses) Boost (10A) GPO's Required Power Rating (kW) Unit Dimensions W x D x H (mm) **Dry Weight (Kg) Tank Material C125 125 no 1x10A 0.25 280 x 476 x 335 20 Stainless C175 175 no 1x10A 0.
Section 1 Tap installation Special Tools Required: In addition to normal tools, the following will be required: For the standard taps: • 35mm diameter sheet metal hole punch for sink tops. (Not supplied) • 35mm diameter hole saw for timber bench tops. (Not supplied) • Nut runner tube spanner (supplied) for fixing tap assembly. When installing a font unit, the following will be required: • 108mm diameter sheet metal or hole saw to suit surface being cut.
HydroTap Tap installation Min 300mm ALL THREAD READ ROD STAINLESS STEEL SPACER 335mm BLACK PLASTIC SPACER SPIDER CLAMP NUT Tap assembly exploded view 1.1 BENCH TOP kitchen layout side view 1.2 Ø35mm Cut a 35mm hole in the bench / sink top. 801525 - Zip HydroTap Installation Instructions - Nov. 2013 - V1.00 Apply a light smearing of silicon sealant on the underside of the spacer to ensure a watertight fit.
Installation Instructions 1.4 1.3 BLACK PLASTIC SPACER Fit the STAINLESS STEEL WASHER, SPIDER CLAMP, AND 6mm NUT. STAINLESS STEEL WASHER SPIDER CLAMP 6mm NUT 35mm hole Pass all the hoses, tubes and USB lead through the 35mm hole. Page 10 of 16 NOTE: feed each of the three tubes and electrical cable evenly in between the legs of the SPIDER CLAMP when installing. 801525 - Zip HydroTap Installation Instructions - Nov. 2013 - V1.
Section 2 Ventilation When installing air flow ducts, the following tools will be required: • Jigsaw and • Keyhole or Wall Board saw. Recommended Installation showing the correct air flow MIN. 35mm Warm Air OUT via kickboard louvre 2.1 **MIN. 100mm Cool Air IN via cabinet floor, front vent grille All Models Proper air circulation must be provided for all Chilled models. The system will operate correctly only if the recommended air gaps are achieved during Installation.
Ventilation C Min. 35mm A B The following instructions are critical if the vent kit, as supplied, is not fitted: If the kick board vent kit cannot be used then it is important to fit a standard HydroTap vent kit, which ensures heat dissipation through natural convection via installed vents. For high use applications, where the cupboard space temperature is near 35°C, or higher, an auxillary ventilation kit must be fitted. (contact your local service centre for availability).
Section 3 Undersink Unit Installation BLUE POWER CORD USB BRAIDED CHILLED OUTLET MAINS IN 3.1 Hose fitting Install the mains water braided hoses to the undersink unit before locating the unit in place. Note: All silicon tubes must be cut to size. They must have a constant fall back to the unit. Note: - Mains hose length is 750mm - Plug and Cord length is 1800mm 3.
Section 4 Commissioning The HydroTap is now ready to be commissioned. • Turn on the power and water and check for any leaks • Familiarise yourself with the operation of the Tap, in preparation for use (See User Guide) • Follow the Installation instructions below (and review Section C of the User Guide). • After commissioning, the system may be customised by selecting further options in Section G Settings, within the User Guide. 4.
Trouble Shooting System Fault Message Power Board Fault Interface Fault Level Board Fault Condenser Screen Blocked Water leak, Isolate Mains Compressor OverRun Water Supply Failure Cold Sensor Open Cold Sensor Closed Flood Sensor Open Condenser Sensor Closed Condenser Sensor Open Compr.
Contact Details Head Office Zip Heaters (Aust) Pty. Ltd. ABN: 46 000 578 727 67 Allingham Street Condell Park NSW 2200 Postal: Locked Bag 80 Bankstown 1885 Australia Website: www.zipheaters.com Facsimile: (02) 9796 3858 Telephone: (02) 9796 3100 Free Call: 1 800 638 633 As Zip policy is one of continuous product improvement, changes to specifications may be made without prior notice. Images in this booklet have been modified and may not be true representations of the finished goods.
