Service manual

FACTORY MENU
3828VD0171G 2-10 DIGITAL FCS- FACTORY MENU
138-F READM: Read mode master channel. 0=Read-
ings A and B fields.
139-F RDPOSYM: Vertical read position.
140-F RSHIFTM: Raster shift master. 1=Enable.
141-F NRONM: Temporal noise reduction. 1= En-
abled.
142-F TNRNR4YM: Temporal noise reduction for
Luma. 1= Enabled.
143-F TNRMD4YM: Motion detection of temporal
noise reduction for Luma. 0=Frame based.
144-F TNRNR4CM: Motion detection of temporal
noise reduction for Chroma. 0=Frame based.
145-F TNRCLYM: TNR luminance classification.
146-F TNRCLCM: TNR chrominance classification.
147-F VAAPRESCM: Vertical low pass filter (pre-
scaler) 0=Disabled.
148-F VPKPRESCM: Vertical peaking. 15= Verti-
cal peaking has no effect.
149-F VCRPRESCM: Shift of chrominance signal.
0=No shift.
150-F NALPFIPM: No active lines per field in-
put.
151-F VPREBYPM: Vertical pre-scaler by pass.
0=enabled.
152-F DPBRT: Brightness level range from 0 to
63. Default is 3.
153-F DPCON: Contrast level range from 0 to 63.
Default is 30.
154-F DPCNS: Contrast noise shaper. 0=disabled.
155-F HORPOSM_H: Default value is 0.
156-F HORPOSM_L: Horizontal position inside ac-
tive picture area. Default value is 325.
157-F VERPOSM_H: Default value is 0.
158-F VERPOSM_L: Vertical position inside ac-
tive picture area. Default value is 16.
159-F HORWIDTHM_H: Default value is 3.
160-F HORWIDTHM_L: Horizontal picture width.
Default value is 32.
161-F VERWIDTHM_H: Default value is 1.
162-F VERWIDTHM_L: Vertical picture width. De-
fault value is 31.
163-F PKCTIBPM AUX: Band pass Peaking factor for
CTI of Aux video inputs. Default value is 3.
164-F PKCTIHPM AUX: High pass Peaking factor for
CTI of Aux video inputs. Default value is 2.
165-F LTIM: Luminance transient improvements.
0=disabled.
166-F APK1BPM: 1
st
adaptive peaking factor (band
pass part). Default value is 0.
167-F APK2BPM: 2
nd
adaptive peaking factor (band
pass part). Default value is 4.
168-F ATH1BPM: Peaking denoising threshold (band
pass part). 0=off.
169-F ATH2BPM: 2
nd
Peaking threshold (band pass
part). 0=0.
170-F THEM: Turning point threshold. Default value
is 3.
171-F APK1HPM_10: 1
st
adaptive peaking factor
(high pass part). Default value is 0.
172-F APK2HPM: 2
nd
adaptive peaking factor (high
pass part). Default value is 3.
173-F ATH1HPM: Peaking denoising threshold (high
pass part). 0=off.
174-F ATH2HPM: 2
nd
Peaking threshold (high pass
part). 0=0.
175-F APK1BPM_32: 1
st
adaptive peaking factor
(band pass part). Default value is 0.
176-F APK1HPM_32: 1
st
adaptive peaking factor
(high pass part). Default value is 0.
177-F CORONM: Coring or denoising for low ampli-
tudes. Default value is 0 (coring off, denoising
on).
178-F DCIONM: Digital contrast improvements. 1=en-
abled.
179-F AB_FTCM: Filter time constant for bright-
ness average. Default value is 0.
180-F PK_FTCM: Filter time constant for frame
peak value. Default value is 0.