SERVICE MANUAL Product Type: Chassis: Manual Series: Manual Part #: Model Line: Product Year: Model Series: Projection/Directview CTV GM CM-150 and PV-150 923-3364R1 A 1998 REVISED EDITION This revised edition includes the original GM manual (923-03364) and the first addendum (923-03419).
PRODUCT SAFETY SERVICING GUIDELINES FOR AUDIO-VIDEO PRODUCTS IMPORTANT SAFETY NOTICE This manual was prepared for use only by properly trained audio-visual service technicians. A.C. Voltmeter When servicing this product, under no circumstances should the original design be modified or altered without permission from Zenith Electronics Corporation.
PRODUCT SAFETY SERVICING GUIDELINES FOR AUDIO-VIDEO PRODUCTS HV SHUTDOW N FOR DIRECT VIEW THEORY OF OPERATION (SHUTDOW N CIRCUIT) latched with its output high until power is removed by turning the TV off. DX3009 and RX3016M pull pin 2 of 3N2 high (about 12 volts). This is the horizontal drive signal pin from the video processor in the small signal module. The video processor turns off horizontal drive when its output is pulled high.
PRODUCT SAFETY SERVICING GUIDELINES FOR AUDIO-VIDEO PRODUCTS HV SHUTDOW N FOR PROJECTION TV SERVICE SAFETY NOTES When servicing chassis, under no circumstance should the original design be modified or altered without permission from Zenith Electronics Corporation. All components should be replaced only with types identical to those in the original circuit, and their physical location, wiring, and lead dress must conform to original layout upon completion of repairs.
TABLE OF CONTENTS Section 6 Schematics and PCBs Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . 6-1 Interconnect Diagram . . . . . . . . . . . . . . . . . . 6-2 9-1650-02 Single PIP . . . . . . . . . . . . . . . . . . 6-3 9-1650-02 Single PIP PCB Layout . . . . . . . . . . 6-4 9-1689-02 Single PIP . . . . . . . . . . . . . . . . . . 6-5 9-1689 Two Tuner Single PIP . . . . . . . . . . . . . 6-6 9-1689-02 Two Tuner Single PIP PCB Layout . . 6-7 9-1783A IF/Audio . . . . . . . . . . . . . . . . . . .
OVERVIEW GENERAL INFORMATION THE GM SERIES CHASSIS FEATURES TW ENTY ONE IC’S. New Video features include a comb filter for processing incoming signals to provide fine detail images. Auto skin tone circuitry automatically maintains natural skin tones. Black level enhancement/white level and peak white level compression circuitry maintains black/white contrast ratio and peak luminance level for detail in both light and dark video areas. Audio features include SoundRite volume control.
MBR3457 REMOTE CONTROL - KEYS DEFINED Indicator Light PRG (Program) Programs remote to operate other products. POW ER Turn TV On or Off TV Selects TV operation MUTE Turns sound Off and On While picture remains. SURF FLASBK (Flashback) Returns to previous channel VOLUME Left/Right Changes TV's sound level. SURF Activates TV channel "Surf" feature. CHANNEL (Up or Down) Selects next channel When "Surf" option is On, you receive only channels set as "Surf" channels. ENTER Shows Channel/Time display.
TRK4000 REMOTE CONTROL - KEYS DEFINED POW ER Turn your Entertainment Machine or any other programmed equipment on or off, depending on mode pow vcr tv INDICATOR LIGHTS Illuminate to show which mode remote is in. cable aux 1 er aux 2 mode MODE LEFT/RIGHT Adjust which mode remote is working in. TRAKBALL Click and move the on-screen pointer. MUTE Press once for Soft Mute, again for Full Mute, and a third time to return to normal volume.
PROGRAMMING THE REMOTES PROGRAMMING THE MBR3457 REMOTE If you’re using Zenith products, the remote is already programmed for the most common codes: TV = 101, VCR = 201, CABLE = 353, and AUX = 401. For other brands, or if your remote fails to control your Zenith products, you’ll have to program the remote. 1. Make sure batteries are installed. 2. Press and hold PRG using a blunt pointed object. Release PRG after indicator light turns on. 3. Press and release button for product being programmed. 4.
PROGRAMMING CODES MBR3457/TRK4000 PROGRAMMING CODES BY BRAND NAME TVS VCRS Admiral 116, 121, 130, 133 Adventura TV/VCR 154 Akai 104 Amark 103, 146 AOC 104 Bell & Howell 121 Broksonic 131, 136, 182 Candle 139 Centurion 119 Citizen TV/VCR AUDIO CD PLAYERS (continued) Admiral 208, 261 Adventura 231 Hitachi TV/VCR 154 Mitsubishi NAD 425, 426, 447 Aiwa 231 LXI 154 Nakamichi 427, 428 Akai 223, 238, 241 RCA 179 NEC 429 Audio Dynamics 202, 206, 218, 247 Samsung 180 On
CM150/PV150 1-6 GM CHASSIS
SERVICE MENU GM CHASSIS A-LINE LINE SERVICE SETUP DIRECTVIEW AND PROJO Audio Coefficients (VCO addition, SAP VCO, SAP LPF, LPF addition, Spectral, and W ideband) - Settings for the audio processor’s stereo decode system. Values, for Service Menu features 74 through 80, are found on a bar code label on top of the Tuner/IF/Audio module. Accessing The Service Menu You may access the menu by using the keyboard or a remote control.
SERVICE MENU GM Service Menu A-18728-03 Ver. 1.
SERVICE MENU GM Service Menu A-18728-03 Ver. 1.
SERVICING - SMALL SIGNAL MODULE REPLACEMENT SMALL SIGNAL (MAIN) MODULE REPLACEMENT AND TOUCHUP CONVERGENCE IMPORTANT ! All convergence data is stored in IC6002, the eight pin Serial EEPROM located on the Micro Module. A complete re-convergence will be required unless this data is retrieved from the original module either by recording the convergence values or transferring IC6002 to the replacement module. Green Convergence Mode Display 3. Start by pressing 1 on remote.
SERVICE - SMALL SIGNAL MODULE REPLACEMENT (continued) ENTER THE STEREO COEFFICIENTS (Bar code data) Will be found on a label attached to the chassis.
PROJO CONVERGENCE SETUP PROCEDURE - MBR3457/TRK4000 Convergence Function Keys Convergence Function Keys Green Convergence Select pow er Blue Convergence Select vcr tv cable aux 1 au x 2 mode Blue Convergence Select SURF Day Red Convergence Select Bow Exit Setup Mode GUIDE PIP PIP ch FREEZ TO DO Convergence Mute surf l flsh n e ch a Skew 1 2 3 4 5 6 In Pin Mid Size Red Convergence Select m *Key / D Key *S-ing / W -M H THEME bk te u l * Size/L Size (Green & Red) *
PROJO CONVERGENCE SETUP PROCEDURE - MBR3457/TRK4000 (continued) 4. Locate physical center of display screen. 5. Look at horizontal line and adjust by loosening yoke clamp and rotating yoke assembly. 6. Using ring magnets set Green CRT beam to center point of screen. 7. Adjust Red horizontal line to convergence with Green horizontal line and Red vertical line 3/4" to right of Green vertical line. Repeat steps 5 and 6 for Blue horizontal and vertical line. 8.
CONVERGENCE SETUP W ORKSHEET Use this chart to record the Red, Green, and Blue convergence setting values. You do not need to copy the "Geometry" settings as they are the result of the red, green, and blue settings. This chart is useful if you have to change a main module and still have a working video display. Check the setup section of this manual for the convergence procedure details.
CM150/PV150 2-9 BOW BOW SKEW SKEW Zone A Zone B 13.2 cm (7.8") 60" - Remaining Area Remaining Area Remaining Area ZONE A PIN PIN 5a 5b D-PIN D-PIN Note: Zones A require the best convergence. In Zone B it is required that in the worst case the images to at least touch. 17.1 cm (6.75") - 15.
CM150/PV150 2-10 GM CHASSIS
TROUBLESHOOTING TROUBLESHOOTING THE GM TELEVISION SYSTEM For most active signal checks and DC voltage measurements, use the right end of RX3401 in direct view products and the left end of RX3401 in projection products for the DC common side of your meter or scope. To take meter readings on the primary side of the switch mode power supply, use front lead of RX3437 in direct view products and the jumper W-3 in projection products for the meter AC common.
TROUBLESHOOTING GM A Line Directview TV POW ER UP CHECKS - DEAD SET Check Standby Conditions Power Supply (E4) 150VDC - RX3401 15VSB - D3414 37VSB - ICX3404 pin4 PwrFa - W 37 SW EEP/HV CHECKS - DEAD SET Sweep ON Conditions Power Supply H DRV - QX3206 C (F2) 40V p-p Check AC Power Then Replace NO Power Supply (E2) (E3) (E2) YES YES Check Standby Conditions Main Module 5VSB - R4108 (C2) NO Check 6A3 Cable Then Replace Main Module Check CRT and Video Output Module.
TROUBLESHOOTING GM A Line Chassis Power Control Projection MAIN MODULE 15VDVCNTL Not Used 8 15V SB <16.35V> (15.9V) PW R CTRL <0V> (3.7V) 12V SW <0V> (11.8V) 37V SBY <39.5V> (37.4V) PW R DD <27V> (28.8V) 3A6 6A3 1 PW R SUPPLY SW EEP MODULE GND GND 8 2G3-3 CM150/PV150 2N3-2 1 < > = STBY ( ) = PW R ON HORZ DRV 3.5V p-p or 1.5V rms VERT DRV 4.
TROUBLESHOOTING GM A Line Projection TV POW ER UP CHECKS - DEAD SET Check Standby Conditions Power Supply (F5) 150VDC - CR3402 C 15VSB - L3416 37VSB - CR3488 cath PW RFA - R3442 SW EEP/HV CHECKS - DEAD SET Check AC Power Then Replace NO Sweep ON Conditions Power Supply (G2) H DRV - R3264 4V p-p / 1V AC Power Supply (E6) (E6) (E5) YES YES Check Standby Conditions Main Module 5VSB - R4108 (C2) NO Check 6A3 Cable Then Replace Main Module YES Check System For Video Shut Down NO (E5) HV ON Conditi
SERVICING GM DIRECTVIEW SERVICE CONTROLS The service menu controls are limited to the G-2, focus, vertical size, and horizontal size. There are controls on the Tuner/IF/Audio Processor module but you will not be able to access these. The service menu is another part of the service adjustments. Checking the service menu setup must be a part of normal servicing. The sheer number of items should not concern you as only some of them may require field adjustment.
SERVICING The GM chassis convergence is controlled by the remote control. To put the projection system into the convergence mode press and hold the MENU key, until the customer menu display disappears, then press 999 ENTER . Now disable convergence by pressing PIP for TRK4000 or FREEZE for MBR remote. Disabling convergence will allow you to see where the uncorrected CRT beam landing is. Check the three yokes for tilt. Loosen the yoke clamp if it is necessary to adjust the tilt.
SERVICE ADJUSTMENTS DIRECT VIEW PURITY & CONVERGENCE SET-UP PROCEDURE PRELIMINARY SET-UP 1. Allow the receiver to warm up for 15 to 20 minutes. 2. Degauss the CRT. 3. Connect a crosshatch generator to the receiver and “rough in” the static (center) convergence. Follow the Convergence Procedure. 4. Adjust for best focus. PURITY ADJUSTMENT 1. Purity tab positioning. Set the 2 pole purity tabs together in the 3 or 9 o’clock positions and the 4 and 6 pole purity tabs together in the 12 of 6 o’clock positions.
SERVICE ADJUSTMENTS DIRECT VIEW (continued) IMPROVING CRT CORNER PURITY CRT’s that display corner purity problems even after following service procedures can be modified with a picture correction kit (P/N 949-50). The purity can be improved by placing a picture correction magnet (included in the kit) on the CRT funnel. Refer to the following modification steps and illustration to place the magnet properly.
SERVICE ADJUSTMENTS Installed GM CRT Assembly Convergence Yoke Assembly 2 Pole Yoke Assembly Lens Assembly Coolant Assembly Transfered Assemblies Replacement CRT Assembly Convergence Yoke Assembly 2 Pole Yoke Assembly Video Module Assembly Coolant Assembly CM150/PV150 3-9 GM CHASSIS
GM DIRECT VIEW - SMALL SIGNAL A Q4101 IC4103 OUT 6A3 IC4104 C W 56 W 12 2D7 B B C W 55 IN E R4108 Q4103 E D4102 E 4L8 Q4104 B R4106 8C3 6H9 W9 IN R4111 C OUT IC4101 2L3 D4103 OUT 9K3 2P6 Q4102 IN IC4102 C B W 97 D R4101 D4101 E 1 C B 1 2K6 1 System Micro R4102 1 1 1 M2 M1 M3 1 1 1 M5 M4 M6 Q890 C R861 2 B For Future Use E C R812 Q845 1 1 1 P1 P2 Q4105 B 1 P3 C 1 P4 1 P6 P5 B Tuner-IF/Audio 1 1 R880 IC800 A1 1 A2 1
GM DIRECT VIEW - LARGE SIGNAL 1 C IC2101 B E R2137 ZD3200 B C Q2101 3G2 C 20 11 B C 3Y3 LX3262 1 3 IN D3207 D3201 GND SENS E QX3201 IC2100 W 81 B ICX3403 TX3401 ZDX3418 3 D2101 DX3423 1 C QX3208 4W 9 10 2 LX3263 R2114 DX3235 E L3401 VR2138 V SIZE 1 3N2 TX3205 1 B E D3203 C3403 D3204 4.0A ICX3404 Q2103 DX3009 1 ZD3233 D3210 D3221 QX3411 QX3206 E QX3202 C B E C D3234 B E 1 E DX3206 E C E B C E B C QX3204 L3402 D3409 anode at top 2.
GM PROJO - SMALL SIGNAL A B C D Q5506 Q5507 Q5509 B Q5502 Q5505 E 1 E 5C2 E C B C D5508 1 E B VMGRA B B C C 9W 4 Q5508 D5503 C C E B E VMBL VMRD VMGR Q4101 IC4103 OUT 2K6 1 System Micro R4102 1 1 M3 1 1 1 1 M2 M1 M5 M4 M6 Q890 3 B C R861 D850 Q845 1 1 1 P1 P2 Q4105 B 1 P3 C 1 P4 1 P6 P5 B E E Tuner-IF/Audio 1 R811 A1 R815 A2 5 2J3 Q5108 C E A CM150/PV150 5 D5 4X9 Comb/Video 1 V4 V3 V5 Source Switch Assembly W 43 8L4 1
GM PROJO - LARGE SIGNAL F G C 1 3H32 CRX3010 CRX3207 3H33 ICX3000 A ICX3200 R3227 R2104 H Size V Size H R CRX3012 E 1 Q3205 3H31 CR3216 E C B CR2101 IC2100 CR3201 Q3100 1 C CR3100 CR3101 3G2 B CR2102 E 2 CR3211 Q3101 B CRX3008 C E 1 3C7 2 3N2 RX3501 Q3502 QX3204 Q3501 G D S E B E B C CRX3009 C CR3505 QX3201 E C B A-17821-03 Assembly con4 con6 con1 con2 con3 con5 3B5 3K9 4F CR3214 DF L3409 CR3415 L3417 A E C B 3D33 CR3420 A CR3011 FX3461
CM150/PV150 3-14 GM CHASSIS
SECTION 4 Model Parts MODEL PARTS A50M84D A-17649-49 LIQUID COUPLER, ASSEMBLY, GREEN 002-04091 CABINET BACK, LOWER, MOLDED PLASTIC A-17649-50 LIQUID COUPLER, ASSEMBLY, BLUE 002-04093 CABINET BACK, UPPER, MOLDED PLASTIC, 50V A-17649-51 LIQUID COUPLER, ASSEMBLY, RED 009-01650-02 MODULE, SINGLE PIP A-17715-02 SHIELD ASSY, PROTECTIVE BARRIER 009-01690-01 MODULE, REGISTRATION A-17821-05 PC DAUGHTER BOARD ASSY, 009-01783-01A MODULE, IF, STEREO A-17869 INFRARED DETECTOR, AMP, ASSEMBLY 009-0
MODEL PARTS (Continued) 057-09080-01 ESCUTCHEON, OPTIC SCREEN, 50V 009-01936-01 MODULE, VIDEO OUTPUT, GREEN 095-04480 TRANSFORMER, DEFLECTION YOKE 009-01937-01 MODULE, VIDEO OUTPUT, BLUE 124-00212-37 SPACE COMMAND, TRANSMITTER, MBR3457 009-01938-01 MODULE, VIDEO OUTPUT, RED 138-01946-01 CABINET GRILLE 009-01942 MODULE, SMALL SIGNAL 192-00858-02 LENS, PRIMARY CONTROLS AND IR 009-01978 MODULE, LARGE SIGNAL 192-00891-01 SCREEN, OPTICAL, PROJECTION TV, 50V, 2MM 012-09224-01 BRACKET, IR SE
MODEL PARTS (Continued) A50M91W1 A-17649-59 LIQUID COUPLER, ASSEMBLY, BLUE 002-04091 CABINET BACK, LOWER, MOLDED PLASTIC, A-17649-60 LIQUID COUPLER, ASSEMBLY, RED 002-04093 CABINET BACK, UPPER, MOLDED PLASTIC, 50V A-17715-03 SHIELD ASSY, PROTECTIVE BARRIER 009-01689-02 MODULE, 2 TUNER SINGLE PIP A-17821-05 PC DAUGHTER BOARD ASSY 009-01690-01 MODULE, REGISTRATION A-17869 INFRARED DETECTOR, AMP, ASSEMBLY 009-01783A MODULE, IF, STEREO A-18035 LINE CORD ASSY 009-01924 MODULE, VIDEO 2H CO
MODEL PARTS (Continued) 138-01950-03 CABINET GRILLE 192-00858-02 LENS, PRIMARY CONTROLS AND IR 192-00891-02 SCREEN, OPTICAL, PROJECTION TV, 56V, 2MM 198-00035 MIRROR, MYLAR, FIRST SURFACE, 56V A-17196-12 BLEEDER ASSY A-17552 LENS & HOUSING, ASSEMBLY, DELTA 77, GREEN A-17552-04 LENS & HOUSING, ASSEMBLY, DELTA 78, RED AND BLUE A-17649-49 LIQUID COUPLER, ASSEMBLY, GREEN A-17649-50 LIQUID COUPLER, ASSEMBLY, BLUE A-17649-51 LIQUID COUPLER, ASSEMBLY, RED A-17715-01 SHIELD ASSY, PROTECTIVE BAR
MODEL PARTS (Continued) 009-01783A MODULE, IF, STEREO A-17869 INFRARED DETECTOR, AMP, ASSEMBLY 009-01924 MODULE, VIDEO 2H COMB FILTER A-18159-10 ACCESSORY KIT, SCREEN PROTECTOR AND RETAINERS, 60V 009-01932 MODULE, MICRO AND PROM A-18682 POWER CORD ASSY 009-01936-01 MODULE, VIDEO OUTPUT, GREEN F-53015 KEYBOARD ASSY, CUSTOMER CONTROLS 009-01937-01 MODULE, VIDEO OUTPUT, BLUE A60M91W 009-01938-01 MODULE, VIDEO OUTPUT, RED 002-04091 CABINET BACK, LOWER, MOLDED PLASTIC 009-01942 MODULE, S
MODEL PARTS (Continued) 198-00030 MIRROR, PLASTIC, FIRST SURFACE, MYLAR, 60V A-17196-12 BLEEDER ASSY A-17552-02 LENS AND, HOUSING ASSEMBLY, GREEN RED AND BLUE A-17649-58 LIQUID COUPLER, ASSEMBLY, GREEN A-17649-59 LIQUID COUPLER, ASSEMBLY, BLUE A-17649-60 LIQUID COUPLER, ASSEMBLY, RED A-17715-02 SHIELD ASSY, PROTECTIVE BARRIER A-17821-05 PC DAUGHTER BOARD ASSY A-17869 INFRARED DETECTOR, AMP, ASSEMBLY A-18159-10 ACCESSORY KIT, SCREEN PROTECTOR AND RETAINERS, 60V A-18682 POWER CORD ASSY F
MODEL PARTS (Continued) A-18650 PC BOARD ASSY, JACKPACK, 22 JACK, INTEQ RF SWITCH A-18682 POWER CORD ASSY F-53063 KEYBOARD ASSY, 10 POSITION IQA32M46W7 009-01689-02 MODULE, 2 TUNER SINGLE PIP 009-01783A MODULE, IF, STEREO 009-01912 MODULE, SMALL SIGNAL 009-01916 MODULE, LARGE SIGNAL 009-01932 MODULE, MICRO AND PROM 009-01935 MODULE, VIDEO OUTPUT, 36V FLAT DIRECT VIEW 009-01939 MODULE, SVM, DIRECT VIEW 009-02034 MODULE, VIDEO, 3D COMB FILTER 014-12284-21 CABINET FRONT, TV, MOLDED PLAST
MODEL PARTS (Continued) IQA56M98D 002-04091 CABINET BACK, LOWER, MOLDED PLASTIC 002-04094 CABINET BACK, UPPER, MOLDED PLASTIC, 56V 009-01689-02 MODULE, 2 TUNER SINGLE PIP 009-01690-01 MODULE, REGISTRATION 009-01783A MODULE, IF, STEREO 009-01925 MODULE, VIDEO 3D COMB FILTER 009-01932 MODULE, MICRO AND PROM 009-01936-01 MODULE, VIDEO OUTPUT, GREEN 009-01937-01 MODULE, VIDEO OUTPUT, BLUE 009-01938-01 MODULE, VIDEO OUTPUT, RED 009-01943 MODULE, SMALL SIGNAL 009-01978 MODULE, LARGE SIGNAL
MODEL PARTS (Continued) 014-12328-01 CABINET MAIN, TV, WOOD 024-03405-05 COVER, JACK PANEL, MOLDED PLASTIC 030-01505-03 DECORATIVE ITEM, OVERLAY, FRONT JACK PACK 046-10555-02 KNOB ARRAY, PUSH-BUTTON, 10 POSITIONS 049-01257-08 SPEAKER, OVAL 049-01364 SPEAKER, ROUND, 2 INCH, PIEZO 057-09081-01 ESCUTCHEON, OPTIC SCREEN, 56V 095-04480 TRANSFORMER, DEFLECTION YOKE 124-00219-01 SPACE COMMAND, TRANSMITTER, TRACKBALL, TRK4000 138-01948-01 CABINET GRILLE 192-00891-02 SCREEN, OPTICAL, PROJECTION
MODEL PARTS (Continued) A-17649-51 LIQUID COUPLER, ASSEMBLY, RED A-17715-03 SHIELD ASSY, PROTECTIVE BARRIER A-17869 INFRARED DETECTOR, AMP, ASSEMBLY A-18542 ACCESSORY KIT, SCREEN PROTECTOR AND RETAINERS, 60V A-18682 POWER CORD ASSY F-53287 KEYBOARD ASSY, CUSTOMER CONTROLS IQA60M98W1 002-04079-03 CABINET BACK, UPPER, MOLDED PLASTIC, 60V, W/ AUDIO JACKS 002-04081-05 CABINET BACK, LOWER, MOLDED PLASTIC 009-01689-02 MODULE, 2 TUNER SINGLE PIP 009-01690-01 MODULE, REGISTRATION 009-01783A MO
MODEL PARTS (Continued) 009-01936-01 MODULE, VIDEO OUTPUT, GREEN 009-01937-01 MODULE, VIDEO OUTPUT, BLUE 009-01938-01 MODULE, VIDEO OUTPUT, RED 009-01978 MODULE, LARGE SIGNAL 012-09224-01 RA46M84D5 BRACKET, IR SENSOR 014-12330-01 CABINET MAIN, TV, WOOD 046-10526-06 KNOB ARRAY, PUSH-BUTTON, 10 BUTTON 049-01257-08 SPEAKER, OVAL 049-01364 SPEAKER, ROUND, 2 INCH, PIEZO 057-09074 ESCUTCHEON, OPTIC SCREEN, 46V 095-04480 TRANSFORMER, DEFLECTION YOKE 124-00212-37 SPACE COMMAND, TRANSMITTER,
MODEL PARTS (Continued) A-17649-53 LIQUID COUPLER, ASSEMBLY, BLUE A-17649-54 LIQUID COUPLER, ASSEMBLY, RED A-17715-02 SHIELD ASSY, PROTECTIVE BARRIER A-17821-05 PC DAUGHTER BOARD ASSY A-17869 INFRARED DETECTOR, AMP, ASSEMBLY A-18648 PC BOARD ASSY, JACKPACK, 10 JACK A-18682 POWER CORD ASSY F-51189 KEYBOARD ASSY, CUSTOMER CONTROLS, 10 BUTTON RA46M84W 002-04081-05 CABINET BACK, LOWER, MOLDED PLASTIC 002-04082 CABINET BACK, UPPER, MOLDED PLASTIC, 46V 009-01650-02 MODULE, SINGLE PIP 009-01
MODEL PARTS (Continued) 009-01978 MODULE, LARGE SIGNAL 012-09224-01 BRACKET, IR SENSOR 014-12314-01 CABINET MAIN, TV, WOOD 046-10555 KNOB ARRAY, PUSH-BUTTON, 10 POSITIONS, STR 049-01257-08 SPEAKER, OVAL 049-01364 SPEAKER, ROUND, 2 INCH, PIEZO 057-09080 ESCUTCHEON, OPTIC SCREEN, 50V 095-04480 TRANSFORMER, DEFLECTION YOKE 124-00212-37 SPACE COMMAND, TRANSMITTER, MBR3457 138-01946 CABINET GRILLE 192-00858-02 LENS, PRIMARY CONTROLS AND IR 192-00890-13 OPTIC FILTER, SCREEN PROTECTOR 192-0
MODEL PARTS (Continued) A-17649-59 LIQUID COUPLER, ASSEMBLY, BLUE 124-00212-37 SPACE COMMAND, TRANSMITTER, MBR3457 A-17649-60 LIQUID COUPLER, ASSEMBLY, RED 138-01946-01 CABINET GRILLE A-17715-02 SHIELD ASSY, PROTECTIVE BARRIER 192-00858-02 LENS, PRIMARY CONTROLS AND IR A-17821-05 PC DAUGHTER BOARD ASSY 192-00890-13 OPTIC FILTER, SCREEN PROTECTOR A-17869 INFRARED DETECTOR, AMP, ASSEMBLY 192-00891-01 SCREEN, OPTICAL, PROJECTION TV, 50V, 2MM A-18648 PC BOARD ASSY, JACKPACK, 10 JACK 198-00
MODEL PARTS (Continued) 009-01938-01 MODULE, VIDEO OUTPUT, RED 009-01942 MODULE, SMALL SIGNAL 009-01978 MODULE, LARGE SIGNAL 012-09224-01 BRACKET, IR SENSOR 014-12315-01 CABINET MAIN, TV, WOOD 046-10555 KNOB ARRAY, PUSH-BUTTON, 10 POSITIONS, STR 049-01257-08 SPEAKER, OVAL 049-01364 SPEAKER, ROUND, 2 INCH, PIEZO 057-09082 ESCUTCHEON, OPTIC SCREEN, 56V 095-04480 TRANSFORMER, DEFLECTION YOKE 124-00219-01 SPACE COMMAND, TRANSMITTER, TRACKBALL, TRK4000 138-01950 CABINET GRILLE 192-00858-0
