machine numbers H 2735DT H3235DT H 3 6 3 5 DT ConciergeTM Direct-View Television Receiver installation & operating guide / warranty
RECORD YOUR MODEL NUMBER The model and serial number of your new TV are located on the back of the TV cabinet. For your future convenience, we suggest that you record these numbers here: MODEL NO.____________________________________ SERIAL NO.____________________________________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 18. Object and Liquid Entry 14. Outdoor Antenna Grounding Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
Table of Contents Turn to the next page to begin the TV setup Safety Warnings Important Safety Information Table of Contents 2 3 5 Step 1. Hook Up TV Hookup Directory TV and other Equipment Hookups Antenna Cable service Antenna with VCR Cable service with VCR External Speaker 6 7 8 9 10 11 Step 2.
Basic Hook-Up Directory This page will direct you to which page to go to for proper hook up of the TV IMPORTANT!! Use this page to decide where you need to begin your set up. First, find the line below that best describes what you want to do, then go to that page number. Antenna only If you are using an antenna and no other equipment, go to . . . . . . . . . . . . . . . . . . page 7 Cable only If you have cable and no other equipment, go to . . . . . . . . . . . . . . . . . . . . . . . . .
Hook Up Your Antenna to the TV Connect an off-air antenna to the TV 1 Locate the Antenna/Cable jack on the back of the TV. 2 Connect the cable that runs from the wall directly to this jack, according to the diagram to the right. 3 Remove the back of the remote and put in two AA batteries. TV back back of remote 4 Antenna Flat wire (300 ohm) ANTENNA CABLE Plug in the TV. Do not plug it into a switched outlet. The TV is designed to operate on standard current, 120volt 60 Hertz AC.
Hook Up Your Cable (CATV) to the TV Connect cable service to the TV 1 Locate the Antenna/Cable jack on the back of the TV. 2 Connect the cable that runs from the wall directly to this jack, according to the diagram to the right. 3 Remove the back of the remote and put in two AA batteries. TV back Cable TV wall jack RF coaxial wire (75ohm) ANTENNA CABLE back of remote VIDEO IN MATRIX OUT M.P.I. 4 R- AUDIO- L IN Plug in the TV. Do not plug it into a switched outlet.
Hook Up Antenna and VCR to the TV Antenna VCR back Connect an off-air antenna and VCR to the TV Flat wire (300 ohm) 300/75 ohm Adapter TV back 1 2 3 VCR back AV panel output In switch 3 4 Out Video Audio Locate the Antenna/Cable jack on the back of the VCR. Connect the cable that runs from the antenna directly to this jack, according to the diagram to the right. As required, make the other connections as shown to the right. ANTENNA CABLE Remove the back of the remote, put in two AA batteries.
Hook Up Cable Service (CATV) and VCR Cable TV wall jack VCR back Connect a VCR and Cable service to the TV. Round wire (75 ohm) VCR back AV panel output In switch 3 4 Out Video Audio TV back 1 Locate the Antenna/Cable jack on the back of the VCR. 2 Connect the cable that runs from the wall directly to this jack, according to the diagram to the right. As required, make the other connections as shown to the right. 3 ANTENNA CABLE VIDEO IN Remove the back of the remote, put in two AA batteries.
External Speaker Hook Up Connect an external speaker to the TV. 1 Locate the Audio In jack on the back of the speaker. 2 Connect a standard audio cable from the Matrix Out jack on the TV, to the Audio In jack on the external speaker. Speaker back Audio In TV back ANTENNA CABLE VIDEO IN MATRIX OUT M.P.I.
Auto Program (Channel Search) Use Auto Program to specify Antenna or cable service incoming signal source and automatically store all of the channels that are found by channel search 1 With the Installer remote control in hand, press the POWER key to turn on the TV. POWER 2 Press MENU repeatedly so the Setup menu appears. 3 Using SELECT on the remote control, highlight Auto Program on the screen. 4 Press a Right or Left ADJ (Adjust) arrow to reach the Auto Program screen.
Front Panel Controls Using the front control panel to access the menus 1 Press ON/OFF to turn on your TV. 2 To access the menus press the MENU button on the control panel. Cycle through the various menus by pushing the button repeatedly. 3 Press the SELECT button repeatedly to highlight the option you want to modify. 4 Press either the Right or Left ADJUST button to modify the option you have chosen. 5 The menu will disappear after a few seconds.
Guest Remote Key Functions A quick list of the keys on the guest remote and what they do FLASHBK (FLASHBACK) Returns to the last channel viewed. CC (CLOSED CAPTIONING) Direct access to closed captions. Press ENTER to exit. POWER Turns TV On or Off. MUTE Turns sound Off and On, while the picture remains. POWER MUTE BK CC FLSH E LUM VO VOLUME (LEFT/RIGHT) Adjusts the sound level. ENTER Press to view the Channel/Time/Audio display or to remove any on-screen display or menu.
Installer Remote Key Functions A quick list of the keys on the LP702 installer’s remote and what they do FLASHBK (FLASHBACK) Returns to the last channel viewed. CC (CLOSED CAPTIONING) Direct access to closed captions. Press ENTER to exit. POWER Turns TV On or Off. MUTE Turns sound Off and On, while the picture remains. POWER BK MUTE FLSH CC TV/FM Selects TV or Radio mode on TVs equipped with FM radio. VOLUME (LEFT/RIGHT) Adjusts the sound levels.
On-Screen Menus Overivew Descriptions of the menus and on-screen displays available to the installer Menu Name Page Description ON-SCREEN MENUS SETUP MENU Adjusts the basic operational features of the TV Auto Program 12 Automatically finds and stores active channels to scroll through using Channel Up/Down. Add/Del/Blnk 17 Manually picks and chooses which active channels will appear when using Channel Up/Down Channel Labels 18 Labels the channels with their network names (ABC, CBS, HBO, etc.).
Setting Add/Delete/Blank Fine-tune the guest’s channel selection list CH 44 ADDED 1 Press the MENU key on the Installer’s remote so the Setup menu appears. 2 Press SELECT repeatedly to highlight the Add/Del/Blnk option. 3 Using either the NUMBER keypad and ENTER or the Channel Up/Down arrows on the remote, select a channel. (If adding a deleted channel, you will need to use the NUMBER keypad and ENTER.
Setting Up Channel Labels Overview Channel Labels help the user identify the channel or network being viewed. In the Setup menu with the CH LABELS option highlighted, use the Adjust Left/Right arrows to scroll through the available channel labels, such as, A & E, AMC, ESPN, HBO, etc. These are a series of alphabetically organized preset labels from which you can choose the more common networks. Use any of these or create custom labels.
Timer Set Up TO SET TIMER Sets the time the TV will automatically turn off Be sure to set the Clock first, see next page. 1 POWER Press MENU to show the Setup menu. BK MUTE FLSH CC 2 3 4 5 Use SELECT to highlight Timer Setup. /FM TV E LUM VO With Timer Setup highlighted as shown above, use the Left/Right ADJ arrow to pick from the preset times, the time that the TV will turn itself off, or set the Sleep Timer to Off to disable it. Press ENTER to set the timer and return to TV viewing.
Set the Clock Sets the TV’s internal clock 1 11:44 PM TIMER Press MENU repeatedly to show the Setup menu. POWER Press SELECT to highlight the Clock Set option. BK MUTE FLSH CC 2 Set the current time; use the Number keypad to enter the hours, then minutes. For example, enter 06, then 30, to set 6:30 on the clock. 3 Use the TIMER key to specify AM or PM. 4 Press ENTER to start the clock and return to TV viewing.
Captions Caption/Text Turns on and selects closed-captions and text options that appear on-screen CAPTION 1 1 In the Setup menu using SELECT on the remote control, select Captions/Text on the screen. 2 Use the Right/Left ADJ arrows to choose any of the following options: Off, Caption 1, Caption 2, Caption 3, Caption 4, Text 1, Text 2, Text 3, or Text 4. 3 Press ENTER to remove menu. 4 Select Captions directly by pressing CC repeatedly to choose: Off, Caption 1, 2, 3, 4, or Text 1, 2, 3, 4.
Language Choose the language for the on-screen menus ENGLISH 1 Press the MENU key on the remote control so the Setup menu appears. 2 Press SELECT on the remote control and repeat, to highlight Language on your screen. POWER BK MUTE FLSH CC /FM 3 4 TV Press a Right/Left ADJ arrow to choose one of the following options: English, Spanish or French. E LUM VO Press ENTER to return to TV viewing.
Audio Menu Adjust the audio options for the guest 1 Press MENU repeatedly on the installer’s remote control until the Audio menu appears. 2 Using SELECT on the remote control, highlight the setting you want to change. Choose from: POWER BK MUTE FLSH CC /FM TV • Bass: Increases/decreases lower-end sounds. E LUM VO • Treble: Increases/decreases higher-end sounds. • Balance: Allows you to put the sound more to the left or right channel.
Video Menu Use the Video menu to customize the picture 1 Press MENU repeatedly until the Video menu appears. Your options are: • Contrast: Adjusts the level of difference between white and black in the TV picture. The more contrast, the brighter the picture appears. • Brightness: Increases or decreases amount of white in the TV picture. POWER BK MUTE FLSH CC • Color: Adjusts levels of all colors in the TV picture. /FM TV E LUM • Tint: Balances between amounts of red and green in the TV picture.
Installer Parental Control Menu If used, this optional feature can “block” undesirable programming from appearing on the TV Parental Control offers the user a wide variety of options and settings that restrict or “block” the programming that can appear on the TV. Parental control allows the user the capability of defining which program rating they consider acceptable, to the younger or more sensitive viewer.
Installer Parental Control Menu After you have read the preceding page, follow instructions below to set up and activate Parental Control 1 MPAA RATING CONTENT BLOCK TO BLOCK DIALOG LANGUAGE SEX SCENES VIOLENCE FV VIOLENCE NO CONTROL Note: Use the installer’s remote control to specify Parental Control settings. 2 As shown above, with the Parental Control menu onscreen, use SELECT to choose an option, like Content Block.
Other Menus & On-Screen Displays Press the remote keys indicated below to access these menus and displays CH 9 3:12 PM STEREO Channel/Time/Audio Display Press ENTER. Shows currently selected channel or source, current time if the clock has been set, and incoming audio signal. Alarm Menu Press ALARM. Sets the time the wake up alarm will sound. Sleep Timer Menu Press TIMER. Sets the time to automatically turn the TV off and shows remaining time before TV shutoff.
Managing the Channel Banks The TV has four channel banks, where the administrator or installer can store groups of TV channels PLANNING THE CHANNEL BANKS Generally, TV channels are grouped into “program packages” with terms that are proposed to the end user. The user then opts for a package. Below is an example of how TV channels may be grouped. You may plan your package by using a chart like the one after the following page.
Managing the Channel Banks Examples of typical channel banks charts filled in Figure 1. Typical channel banks after running Auto Program B Purpose A N K 1 2 3 4 5 6 7 8 9 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 A A A A A A A A A A A A A A A 2 A A A A A A A A A A A A A A A 3 A A A A A A A A A A A A A A A 4 A A A A A A A A A A A A A A A A = Active - - Channel was found during AUTO PROGRAM Figure 2.
Managing the Channel Banks PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies) B Purpose A N K 1 2 3 4 5 6 7 8 9 Channel Number 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 B Purpose A N K Channel Number 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 2 3 4 B Purpose A N K Channel Number 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 1 2 3 4 B Purpose A N K Channel Number 76 77 78 79 80 81 82 83 84 85
Installer menus Use the Installer menus to make adjustments Accessing the Installer menu 1390-00 0.00 01 Installer menus can be accessed by using the installer’s remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. To exit the Installer menu, press ENTER again. Any changes you make will be stored in nonvolatile memory. The Installer menu opens with item 03, VERT POS. Press the Up/Down arrow keys to sequence through the various items.
Installer menus Use the Installer menus to make adjustments 00 FACT MENU (Factory Mode) Used to access and customize Installer menu settings using the installer type remote. If some channels were not found by AUTO PROGRAM, select the appropriate AFC setting here and add the channels using the ADD/DEL option in the Setup Menu. 01 PRESET PX (Preset Picture) Saves your custom video settings (color, tint, contrast, and brightness) in nonvolatile memory (not affected by power loss).
Installer menus Use the Installer menus to make adjustments The range of values is 0 - 255. Use (adjust) keys to choose: (1) With number 255 the feature is inactive. (2) Other numbers determine the start channel. (3) Set the volume level as desired before exiting the Installer menu. 0 is the “AUX” channel. 11 HOSPITAL MODE Not used in Concierge-series TVs. Leave at default setting 0.
LT1500 QuickSet Programmer Use the LT1500 QuickSet Programmer to duplicate the TVs setup The optional QuickSet II Programmer (LT1500) allows custom setup and programming information to be quickly copied from a master TV into multiple television sets. Once learned from the master, setup data is retained in the LT1500 for future use and recall. When using the LT1500, operation will be easier if the TV set is connected to a good quality signal and operating with a stable picture displayed.
Clone Selection Menu Choices Use the LT1500 QuickSet Programmer to duplicate the TVs setup Item 2: Teach the TV 1 Press (2) then ON/OFF, POWER, or ENTER to begin the teaching process. Alternatively, use the TV front panel CHANNEL UP or CHANNEL DOWN keys to highlight your choice, then press ON/OFF, POWER, or ENTER to activate. 2 3 The next screen will allow you to choose which of the 4 available memories will be copied to this TV.
Clone Selection Menu Choices Use the LT1500 QuickSet Programmer to duplicate the TVs setup Item 6: Display Clone Setup 1 Press (6) then ON/OFF, POWER, or ENTER to begin the teaching process. Alternatively, use the TV front panel CHANNEL UP or CHANNEL DOWN keys to highlight your choice, then press ON/OFF, POWER, or ENTER to activate. 2 The TV screen will display the memory selection menu. 3 Press the desired memory number, then ON/OFF, POWER, or ENTER to display the contents of the selected memory.
Maintenance Routine TV cabinet and screen cleaning Careful and regular cleaning can extend the the useful service life of the TV. Be sure to turn the power off and pull out the plug before you begin any cleaning. Screen Cleaning 1. Here’s a great way to keep the dust off the screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2.
Troubleshooting Some quick and easy tips to resolving problems SYMPTOMS SOLUTIONS Snowy picture and unclear sound. • Check your antenna connection or location • Check your cable input. • Check to see if the TV/.VCR button on your VCR has the TV selected Multiple images or ‘ghost shadows.’ • Check your antenna direction and/or location. • Check your cable input • Make sure the cable from your antenna to your Entertainment Machine is properly connected.
Glossary A list of definitions for words found in this guide 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the threaded jack on the back of the TV. 300 TO 75 OHM ADAPTER A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end.
Guest Remote Control Key Functions A quick list of the keys on the guest remote and what they do FLASHBK (FLASHBACK) Returns to the last channel viewed. CC (CLOSED CAPTIONING) Direct access to closed captions. Press ENTER to exit. POWER Turns TV On or Off. MUTE Turns sound Off and On, while the picture remains. POWER MUTE BK CC FLSH E LUM VO VOLUME (LEFT/RIGHT) Adjusts the sound level. ENTER Press to view the Channel/Time/Audio display or to remove any on-screen display or menu.
Guest Parental Control Menu This optional feature can be used to “block” undesirable programming from appearing on the TV This TV offers the user a wide variety of options and settings that restrict or “block” the programming that can appear on the TV. Parental control allows the user the capability of defining which program rating they consider acceptable, to the younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the secret 4-number code, the password.
Guest Parental Control Menu After you have read the preceding page, follow instructions below to set up and activate Parental Control CHANNEL PREVIEW Parental Control 5 - - - 9 - - - 20 - - - 32 - - - 44 - - - 66 - - - VIDEO CONTENT BLOCK DIALOG LANGUAGE TV-MA SEX SCENES VIOLENCE F VIOLENCE NO CONTENT MPAA RATING TO BLOCK Note: The lodge decides if the Parental Control feature will be available to the guest. If available, Parental Control will appear as an option in the CH (CHANNEL) PREVIEW menu.
Menus & On-Screen Displays Press the remote keys indicated below to access these menus and displays CH 9 3:12 PM STEREO Channel/Time/Audio Display Press ENTER. Shows currently selected channel or source, current time if the clock has been set, and incoming audio signal. Alarm Menu Press ALARM. Sets the time the wake up alarm will sound. Use number keypad and TIMER to set AM/PM. Sleep Timer Menu Press TIMER. Press repeatedly to set the Sleep Timer. Shows remaining time before TV shutoff.
Zenith ConciergeTM Direct-View TV Receiver Warranty Direct-View Color TV Welcome to the Zenith family! We believe that you will be pleased with your new Zenith TV. Please read this warranty carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state within the U.S.A.
