PRIME/ESSENTIAL NAVIGATION QUICK START GUIDE EN
Initial set-up 1. Select your preferred language, then tap selection. Later you can change it in Regional settings. to confirm your 2. Read the End User Licence Agreement, and tap the terms of use. 3. The Configuration wizard starts. Tap 4. Select the language and speaker used for voice guidance messages and tap if you agree with to continue. . Later you can change it in Regional settings. Tap any item in the list for a short voice sample. Tap to confirm your selection. 5.
Map screen The map screen is the most important and frequently used screen of the software. During navigation, the screen shows route information. The map shows the current position (a green arrow by default), the recommended route (an orange line), and the surrounding map area. When there is no GPS position, the current position arrow is transparent. It shows your last known position. When a GPS position is available, the current position arrow is displayed in full colour showing your current position.
Navigation menu On the Map screen, tap to open the Navigation menu. You can see the following menu options when you are navigating without a planned route: Button Instruction Select your destination by entering an address or its coordinate, or by selecting a Place, a Saved Location, or a Saved Route. You can also look up your recent destinations from the Smart History. Build your route from one or more route points.
In the navigation menu, you have the following additional options: Button Instruction Open the Saved Locations screen where you can save a location as a favourite destination or edit a saved location. Set the volume or mute the navigation. Switch to 3D mode. Switch to 2D mode. Switch to 2D North up view mode. Suspend navigation. Resume navigation. Access the User profiles menu where you can create new profiles or edit the existing profiles.
New Route menu In the Navigation menu, tap to specify an address as your destination. The New Route to... menu provides the following options: Button Instruction Find your destination regardless of its type in (Undefined variable: BrandingVariables.NameOfIQS). Specify an address as your destination. Select a place of interest as your destination. Choose from the list of your saved locations. Choose from the list of all recent destinations.
Navigating to an address on the Navigation view to access the Navigation menu. Tap In the Navigation menu, tap and screen proposes the city or town where you are located. . By default, the To change the country, perform the following steps: . 1. Tap 2. Use the keyboard to enter the name of the country. After entering a couple of characters, the names that match the string appear in a list. 3. Tap choice.
2. Enter the house number on the keyboard. (To enter letters, tap 3. Tap .) and select the street name and the house number. The map appears with the selected destination in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( ) appears at the new location. (optional) To change some of the route setting parameters, perform the following steps: 1.
Using combined search You can initiate a separate search for addresses, Places, saved locations, or recent destinations, but the fastest way to search for any of these is to use combined search. 1. On the Map screen, tap to access the Navigation menu and then . 2. and the combined search screen appears. Right next to the Tap input field, you can see the search area, the city/town around which the search is carried out. The default search area is the area where you are located.
7. The map appears with the selected destination in the middle. If necessary, tap the map ) appears at the new somewhere else to modify the destination. The Cursor ( location. 8. (optional) If needed, change some of the route setting parameters. 9. Tap destination. 10. to confirm the destination, or tap to select a different After a short summary of the route parameters, the map appears showing the entire route. Wait for a few seconds or tap .
Navigating to a place of interest 1. On the Map screen, tap to access the Navigation menu. In the Navigation menu, tap , then tap pre-set search categories: 2. . You are offered the following • to get a list of petrol stations along the route or if it is Tap not available, around your current position or your last known position. • to get a list of accommodation near the destination, Tap around your current position or your last known position.
An example of navigating to a place of interest For example, to find a park around your destination, perform the following steps: 1. to access the Navigation menu. In the Navigation menu, On the Map screen, tap tap , then tap . to open the Search By Category window. 2. Tap 3. Select the area around which the Place should be searched for. Tap the button and select . 4. 5. Browse the list of place categories, and tap one of them. 6. Tap down your search. 7. Tap any of the list items. 8.
Useful Information menu The Useful Information menu provides various additional functions. In the Navigation menu, tap . You need an Internet connection via your mobile phone to access online services (for example, parking and weather information). Button Description Shows information on the current position (latitude, longitude, nearest town, next crossing street, and so on) or the last known position if GPS reception is not available. Offers assistance near your current position.
Settings menu You can configure the program settings, and modify the behaviour of Zenec Navigation. Tap , and . Scroll down to view more options. The Settings menu provides the following options: Button Instruction Select the type of vehicle you are driving, the road types used in route planning, and the route planning method. Adjust the different sound volumes. Enable and set up warnings for speed limit, alert points (such as speed cameras), and road signs.
© Copyright 2015 RevA / copy deadline: Q3-2015
