Step 1 Step 2 Go to User Manual (see pages 2-12) © 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
User Manual (Contents as in Zen-Me in-App version and www.zenme.
WARNING For product warnings and other important safety information, read the Zen-Me Safety Guide (zenme.io/safetyguide). Device Overview Charging and Battery The Zen-Me Sensor contains a rechargeable, built-in Lithium-Polymer (LiPo) battery. The battery charge lasts for up to 12 months and is recharged using the Zen-Me wireless charger. © 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
Battery Charging Allow 2.5 hours to charge the battery from zero to full capacity at the optimal charging temperature of 21°C (70°F). At other temperatures, the battery may take longer to charge or fail to reach 100% charge. The sensor will not charge at temperatures outside the approved range of 0°C to 45°C (32-113°F). Placing the sensor or charger in direct sunlight will heat the devices and affect charging capability. Plug the USB-cable into the Zen-Me charger.
NOTICE The sensor will not charge when the ambient temperature is outside the approved charging temperature range of 0°C to 45°C (32-113°F). Do not place any object other than the sensor onto the wireless charger as this could damage the device. Do not try to charge the sensor with accessories attached. This will damage the charger and sensor. Battery Level NOTICE The sensor monitors the battery level and provides status information when connected to the Zen-Me App.
Battery Life NOTICE Battery life and the rate of power consumption are affected by a number of factors: ST YLE OF USE INTENSIT Y OF ME A SUREMENT WIRELESS ENVIRONMENT Depending on how the sensor is used, it has more or fewer features enabled. The more features activated, the greater the power demand. The frequency settings selected for data acquisition and transmission influence the rate of power usage (see table below).
Getting Started Use the Zen-Me App on your iPhone to control the sensor, monitor your data and experience Zen-Me’s functionality. The App includes a detailed user-manual to help you get the most from Zen-Me. Follow the instructions below to install the Zen-Me App in 4 easy steps. NOTICE The Zen-Me sensor will not work unless it is paired to a mobile device with the Zen-Me App installed and set up. The Zen-Me App is compatible with devices running iOS 10.1 and later.
Pairing the Sensor When prompted by the Zen-Me App, turn on the sensor to start pairing. Follow the instructions on the App. Turn on the sensor by pressing the Power Button. 3 flashes indicate the sensor is turned on. Repeated flashes at one second intervals indicate the sensor is ready for pairing. If the sensor has not paired after 60 seconds, it turns off automatically. Turning on the Sensor Press the Power Button. © 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
Placing the Sensor Zen-Me sensors give you endless possibilities. They are small, versatile and can be placed almost anywhere to support a limitless choice of uses and activities. Discover a range of Use Cases in the Explore section of the Zen-Me App. Grab your favorite Use Case and access helpful advice on the best way to locate and use your sensor(s). You can even create your own Use Case from scratch if you prefer.
Resetting the Sensor To reset the sensor, press and hold the Power Button for 30 seconds. One long flash followed by short, repeated flashes indicates the sensor is reset and ready for pairing. Sensor Flight Mode During Flight Mode your sensor continues to gather data, but does not connect or stream data to your mobile device. When flying, this ensures your sensor does not interfere with aircraft communications systems.
Turning off Flight Mode Press power button once to deactivate Flight Mode. 2 long (2 second) flashes indicate that Flight Mode is turning off. Once flight Mode is switched off you can connect the app with sensor again. NOTICE You can use Flight Mode to save battery on your sensor, if you will not connect your sensor for long time. This will shut down the Bluetooth Radio but keeps the sensor operating.
Requirements Zen-Me requires a compatible iPhone 6 or above with iOS 10.1 or above, and installation of the free Zen-Me App. Use requires registration of a Zen-Me account and acceptance of Zen-Me Terms of Service (zenme.io/terms). Disclaimers • • • • All information within this Safety Guide is subject to change without notice or warning. Zen-Me Inc. cannot be held liable for any losses resulting from the use of Zen-Me devices or the Zen-Me App.
Step 1 Step 2 Go to Safety Guide (see pages 2-6) © 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
Safety Guide (Contents as in Zen-Me in-App version and www.zenme.io/safetyguide) Important Safety Information for your Zen-Me devices. CONTENTS Responsible Use 2 Care and Maintenance 2 Changes and Modifications 3 Batteries 3 Charging 3 Prolonged Heat Exposure 4 Choking Hazard 4 Radio Frequency Radiation Exposure 4 Regulatory Information 5 Disposal and Recycling 5 Disclaimers 5 Support 5 © 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
For user manual and other important information about Zen-Me products maintenance, read the Zen-Me User Manual (zenme.io/manual). Responsible Use C AUTION Zen-Me devices include sensitive electronic components (including batteries).
Changes and Modifications C AUTION Making changes or modifications to Zen-Me devices could expose the user and others to injury and may invalidate your authority to operate the devices in compliance with local regulations. Batteries Zen-Me Sensors contain built-in wireless re-chargeable Lithium Polymer (Li-Po) batteries. C AUTION Batteries are a potential health hazard and may cause serious injury or death. C AUTION Do not attempt to open the sensor case to replace the battery yourself.
Prolonged Heat Exposure C AUTION Prolonged physical contact with a Zen-Me Sensor, Zen-Me Charger, power adapter or charging cable when plugged into a power source may cause heat exposure, discomfort or injury. Avoid sitting, resting or sleeping on the Zen-Me Sensor or Zen-Me Charger when connected to a power source or charging is taking place, either in direct contact or if the devices are under clothing, blankets or pillows.
Regulatory Information This device complies with part 15 of FCC rules and with ISED license-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission (FCC) Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
Zen-Me Sales Package User Manual Design Booklet for ZMH01A and ZMT01A © 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
