Instruction manual

68 ZVC355-001_v02
FOAM OUTLET FILTER
1
In order to replace the foam outlet lter (14) press the
fastening on the cover of the lter, and remove the cover of
the lter from the vacuum cleaner.
2
Pull the handle situated on the frame of the foam outlet
lter (15) to the right, pull the frame aside towards you, and
remove it from the vacuum cleaner.
3
Remove the foam outlet lter from the frame.
If the foam outlet lter (14) is dirty, you may replace it with
a new one, clean it or rinse it with running water. Before
reinstalling the lter, make sure it is dry.
 Forsafetyreasonsitisunacceptabletoinstall
awetordamagedfoamoutletlter(14).
4
Place the new/rinsed lter carefully into the frame.
5
Situate the frame with the foam outlet lter (14) into
the vacuum cleaner, so that both of the fastenings on the
right side are tted into the holes in the body of the vacuum
cleaner.
6
Block the frame from its left side in such a way that the
fastenings of the frame are inserted into the holes in the
body of the vacuum cleaner.
7
Place the lter cover in such a way that the two
protrusions situated in the lower part of the cover are
inserted into the holes in the body of the vacuum cleaner,
then press the lter cover to snap the fastening in the body
shut. A characteristic “click” signalizes the cover has been
properly installed.
 Do not use the vacuum cleaner without the
inletltersandtheouterlterinstalled.
 Always replace damaged lters with original,
brandnewones.
TUBE OF THE CYKLON DUST CONTAINER
It is necessary to periodically clean the tube of the CYKLON
dust container.
1
Remove the CYKLON dust container and empty it, as
described in para. C.
2
Press the button situated on the CYKLON dust container,
and open its bottom. If the CYKLON dust container is full,
empty it as described in para. C.
3
Remove the tube of the CYKLON dust container from the
container.
4
If the tube of the CYKLON dust container (19) is dirty,
it may be rinsed with running water. Before reinstalling the
tube, make sure it is dry.
5
Insert the rinsed tube of the CYKLON dust container into
the socket of the container in such a way that the protrusion
situated on the ange of the tube is situated in the socket of
the body of the container. The other end of the tube is to be
inserted into the round socket situated on the bottom of the
chamber, where the tube is placed.
E
F
 It is forbidden to wash lters in washing
machinesordishwashers.
  Filtersmaybedriedonlynaturally.
  Donotusehairdryers,heatersorradiatorsto
drylters.
 Before replacing the lters make sure the
vacuumcleanerisoff,andtheplugofthecord
isunpluggedfromthesocket.
EPA INLET FILTER AND FOAM INLET FILTER
It is necessary to periodically clean the EPA inlet lter and
the foam inlet lter to remove small fractions of dust.
Remove the CYKLON dust container and empty it, as
described in para. C.
1
Remove the EPA inlet lter (16) from the CYKLON dust
container.
2
Remove the foam inlet lter (17). If the foam inlet lter
(17) is dirty, you may replace it with a new one, clean it or
rinse it with running water. Before reinstalling the lter, make
sure it is dry.
The main function of the foam inlet lter (17) is to protect the
EPA inlet lter (16) against excessive dirt.
 Forsafetyreasonsitisunacceptabletoinstall
awetordamagedfoaminletlter(17).
●
Clean the pleats of the EPA inlet lter (16), and if the lter
is damaged, it should denitely be replaced with a new
one. If the EPA inlet lter (16) is dirty, you may replace
it with a new one, clean it or rinse it with running water.
Before reinstalling the lter, make sure it is dry.
 Forsafetyreasonsitisunacceptabletoinstall
awetordamagedEPAinletlter(16).
●
Situate the new/rinsed foam inlet lter in the previously
determined spot.
3
Place the new/rinsed EPA inlet lter (16) in the previously
determined spot in the dust container.
4
Situate the CYKLON dust container with the installed
EPA inlet lter (16) in the chamber of the vacuum cleaner.
A characteristic “click” signalizes the container has been
properly installed.
 We advise you to replace the EPA inlet lter
(16)withanewoneevery6monthsofuse.
 DonotusethevacuumcleanerwithouttheEPA
inlet lter (16) installed in the CYKLON dust
container. If the EPA inlet lter is not there,
it is impossible to situate the CYKLON dust
containerinthevacuumcleaner.
D