Instruction manual

69ZVC315-001_v02
 Do not vacuum without HEPA/EPA inlet lter
(14) installed in “CYCLONE” dust container.
LackofHEPA/EPAinletlter(14)shallprevent
insertionof“CYCLONE”dustcontainertothe
vacuumcleaner.
“MICROFILTER” OUTLET FILTER AND OUTLET
FOAM FILTER
1
In order to replace “Microlter” outlet lter (12) press the
hook located in the lter cover and pull out the lter cover
from vacuum cleaner.
2
Pull out the “Microlter” outlet lter (12).
If the “Microlter” outlet lter (12) is dirty, you can replace it with
a new lter, you can clean it or rinse with running water. Do not
forget to dry above mentioned lter before re-installation.
 Forsafetyreasonsitisunacceptabletoinstall
the moist or defective “Microlter” outlet
lter(12).
3
Carefully insert a new / rinsed lter to previously
occupied space.
4
Pull out the foam outlet lter from lter cover (1).
If the outlet foam lter (13) is dirty, you can replace it with
a new lter, you can clean it or rinse with running water. Do
not forget to dry above mentioned lter before re-installation.
 Forsafetyreasonsitisunacceptabletoinstall
themoistordamagedoutletfoamlter(13).
5
Carefully insert a new / rinsed lter to previously
occupied space.
6
Put the lter cover so that two tips located at the right
side of the cover should hit the holes in the body of the
vacuum cleaner, press the lter cover so the hook snapped
in the body. Characteristic “click” sound informs, that the lter
cover has been properly installed.
 Do not use the vacuum cleaner with no inlet
andoutletltersmountedinthedevice.
 Damagedinletandoutletltersmustbealways
replacedwithnew,factoryoriginallters.
THE CONE OF “CYCLONE” DUST CONTAINER
It is necessary to clean periodically the “CYCLONE” dust
container cone.
1
Disassembly “CYCLONE” dust container according to
point (C).
2
Press the button located on “CYCLONE” dust container
and open the bottom of the container. If “CYCLONE dust
container is full, empty it according to the point (C).
3
Turn the cone left, so the two tips located on the ange of
the cone were put out from the slots of the container. Put out
the cone.
4
If the “CYCLONE” dust container cone (17) is dirty, you
can rinse it with running water. Do not forget to dry above
mentioned cone before re-installation.
E
F
Disassembly of lters
 Incaseofdirtylters:inletlter,foamlter(15),
HEPA/EPAinletlter(14),outletfoamlter(13),
“Microlter”(12)youcanreplacethemwithnew
lters,cleanthemorrinsewithrunningwater.
  Donotwashthelterinthewashingmachine
ordishwasher.
  Filterscanbedriedinnaturalwayonly.
  Do not dry the lters using hairdryers,
onheatersandradiators.
 Before replacement of lters make sure that
vacuumcleanerisswitchedoffandconnection
cableplugispulledoutfromthewalloutlet.
INLET FILTER HEPA/EPA AND FOAM INLET FILTER
Vacuum cleaners are equipped with inlet lter HEPA type
H13 or EPA.
It is necessary to clean periodically the inlet lter HEPA/EPA
(14) in order to remove minor fractions of the dust, and foam
inlet lter (15) must be also cleaned.
Disassembly the “CYCLONE” dust container and empty it in
accordance with paragraph (C).
1
Remove the HEPA/EPA foam inlet lter (14) from
“CYCLONE” dust container.
2
Remove foam inlet lter (15). If the foam inlet lter (15)
is dirty, you can replace it with a new lter, you can clean
it or rinse with running water. Do not forget to dry above
mentioned lter before re-installation.
The main function of the foam inlet lter (15) is to protect
HEPA/EPA inlet lter (14) against excessive dirt.
 Forsafetyreasonsitisunacceptabletoinstall
themoistordamagedfoaminletlter(15).
●
Clean the pleats of HEPA/EPA inlet lter (14), in case
of lter damage it should be absolutely replaced with
a new lter. If HEPA/EPA inlet lter (14) is dirty, you can
replaced it with a new lter, you can clean it or rinse with
running water. Do not forget to dry above mentioned lter
before re-installation.
 Forsafetyreasonsitisunacceptabletoinstall
themoistordamagedinletlterHEPA/EPA(14).
●
Insert a new/rinsed inlet foam lter (15) into previously
occupied space.
3
Insert a new/rinsed HEPA/EPA inlet lter (14) to the dust
container into previously occupied space.
4
Insert “CYCLONE” dust container with mounted HEPA/
EPA inlet lter (14) to vacuum cleaner chamber. The
characteristic “click” indicates that container has been
correctly mounted.
 It is recommended to replace HEPA/EPAinlet
lter(14)withanewoneevery6monthsofuse.
D