Z E K T O R Ho m e T h e a t e r Switches Digital Video / Component Video / Multichannel Audio HDS4.
What’s Inside Contents Thank you for your purchase of your HDS4.1 H igh D efinition Compo nent Video Switch. What’s Inside...................................... 1 An Overview of the HDS4.1................. 3 Easy, Simple, Instructions!.................. 5 Three Simple Steps to a Remote!......... 7 Controlling the Front Panel Lights...... 9 Adjusting the Front Panel Intensity... 11 Setting the Initial Power On State..... 13 Disabling Front Panel or Remote.. .....
An Overview of the HDS4.1 Front Panel Controls: Front Panel 1 2 ZEKTOR 1 2 3 4 1. 2. 3. 4. 5. 6. Power I ndicator. Lights up in standby mode. S elec tion LEDs. I ndicate cur rently selec ted inputs. I nput S elec tion Buttons. I nfrared R emote S ensor Window. I nfrared R eceived I ndicator. Flashes when IR is received. Power Toggle Button. 3 4 5 6 Rear Panel Connections: 1. Rear Panel 1 2 2. 3.
Step 1: Make the appropriate connections. Easy, Simple, Instructions! To Composite Monitor w/Analog Audio R/V L/H C/V R/V L/H C/V R/V L/H C/V R/V L/H C/V R/V L/H 1 C/V 2 Step 1...
Step 1: Put the HDS4.1 into the Setup Mode ZEKTOR 1 2 3 Three Simple Steps to a Remote! 4 The HDS4.1 features Zektor ’s Exclusive I ntelligent-IR™, and with ver y few exceptions can be setup to use any remote you can point at it! Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right.
Step 1: Place the HDS4.1 into the Setup Mode ZEKTOR 1 2 3 Controlling the Front Panel Lights 4 There are four different front panel light modes available on the HDS4.1. They are: • • • • Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right.
Step 1: Place the HDS4.1 into the Setup Mode ZEKTOR 1 2 3 Adjusting the Front Panel Intensity 4 Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right. 1 2 3 2 • 4 The HDS4.1 is placed into the setup mode by pressing and holding the Power button for about 4 seconds. Press the ‘4’ button to selec t “Front Panel I ntensit y ” option.
Step 1: Set the HDS4.1 to the preferred initial power on state ZEKTOR 1 2 3 Setting the Initial Power On State As long as the HDS4.1 is plugged in, it will remember the previously selec ted input in standby mode. When powered up by pressing the Power button, it will retur n to that previously selec ted channel. 4 However, if power is removed (for instance a plug str ip used to power the HDS4.1 is tur ned off ), and then re -applied, the HDS4.1’s default behavior is to enter into the standby mode.
Step 1: Enter the Enable / Disable Control State ZEKTOR 1 2 3 Disabling Front Panel or Remote I f you are not planning on using a remote control with your HDS4.1, you might want to disable its remote control func tion. 4 Or if you have a household with young cur ious fingers that likes playing with buttons, you also have the capabilit y of disabling the front panel switches and only operating the HDS4.1 with a remote. To enable/disable the front panel switches or remote capabilities...
Resetting to Factory Defaults Step 1: Reset All Parameters to Factory Defaults ZEKTOR 1 2 3 4 I f, for whatever reason, you’d like to reset your HDS4.1 back to its fac tor y condition, this is easily done... Step 1: Reset All Parameters to Factory Defaults 1. 2. 3. 1 2 Start by pressing and holding the Power button... 3 16 HDS4.1 Component Video Switch First press and hold the Power button While continuing to hold the Power Button, press and hold both the ‘2’ and ‘3’ buttons.
Specifications Specifications: Analog Channels Bandwidth @ -0.1db: Bandwidth @ -3db: Resolution: Input Coupling: Output Coupling: 0Hz - 70MHz, All channels Greater than 200MHz, All channels 480i - 1080p, All HDTV modes D.C. D.C. Digital Audio Channels Inputs: Outputs: Maximum Transfer Rate: Digital Audio Modes: Coax Input Level Range: Coax Output Level: Power Requirements: Optional International: Power Supply: Dimensions: Warranty: 18 HDS4.
Warranty Policy Contact Information Warranty Policy Instructions for Returning Items ZEK TOR war rants this produc t against defec ts in mater ial and wor kmanship under nor mal use and ser vice for t wo years from the or iginal date of purchase. ZEK TOR, at its option, shall repair or replace the defec tive unit covered by this war rant y. Please retain the dated sales receipt as evidence of the date of purchase. You will need it for any war rant y ser vice.
Z E K T O R ZEKTOR 12675 Danielson Ct Suite 401 Poway, CA 92064 858•748•8250 www.zektor.
