Installation Guide Installation/Setup/Equipment
Page 1 IMPORTANT: Be sure to check the software version of the Sony DVP-CX777ES 400 disc DVD changer. Please see APPENDIX 1 (Page 8) for more information.
Page 2 Introduction: VideoReQuest brings ReQuest’s award-winning user interface to video control. Its simple, intuitive interface allows you to easily control up to 4 Sony 400 disc DVD changers. Enjoy the convenience of selecting any of the 1600 DVD discs in a collection, with the powerful control of our on-screen user interface.
Page 3 Video Switching Options for VideoReQuest 1. VideoReQuest and Direct RS-232 Control of Switchers and Receivers a. Works with 1-3 DVD Changers b. For a simple, out of the box, no programming solution, the VideoReQuest supports direct RS-232 control of the following video and audio switchers and receivers: i. Zektor HDS4.2 with RS-232. 1. Supports 4 YUV, SPDIF/TosLink Input, 1 Output. See http://www.zektor.com. Contact ReQuest Multimedia for special pricing. ii. KeyDigital KD-SW4x1 / Flash4. 1.
Page 4 1. VideoReQuest and Direct RS-232 Control of Switches and Receivers Zektor Switch Pro: Quality Con: No Composite or S-Video Inputs KDS Switch Pro: Inexpensive Con: No optical, Composite or S-Video Inputs VideoReQuest with a Zektor or Key Digital Switch 1) Connect the VideoReQuest Audio and Video to Input 1 of the switch. 2) Connect 1-3 DVD Changers’ Audio and Video to Inputs 2-4. 3) Connect the RS-232 cable from the DVD changers to ports 1 – 3 of the VideoReQuest.
Page 5 2. VideoReQuest Control of Switchers and Receivers for Video Distribution Sima Switch Pro: Simultaneous Composite & Component Switching Upscale Composite & S-Video to Component Con: Only 3 Component Inputs NOTICE: If you run VideoReQuest in 720p mode, DO NOT connect the S-Video cable as it will degrade the quality of the output. VideoReQuest with a Sima Switch 1) Connect the VideoReQuest Audio and Video to Input 1 of the switch. 2) Connect 1-3 DVD Changers’ Audio and Video to Inputs 2-4.
Page 6 VideoReQuest with Xantech Control 1) Connect the VideoReQuest Audio and Video to the receiver (Can be Composite, SVideo, or Component). 2) Connect 1-3 DVD Changers’ Audio and Video to the receiver. 3) Connect the RS-232 cable from the DVD changers to ports 1 – 3 of the VideoReQuest. 4) Connect Port 4 of the VideoReQuest to the Xantech RS232IR module. 5) In the VideoReQuest Menu, go to Video Switch setting to set the appropriate switch. 6) Connect the IR emitter or plug to the receiver.
Page 7 VideoReQuest with Pronto 1) Connect the VideoReQuest Audio and Video to the receiver (Can be Composite, SVideo, or Component). 2) Connect 1 DVD Changers’ Audio and Video to the receiver. 3) Connect the RS-232 cable from the DVD changers to port 1 of the VideoReQuest. 4) Program the Pronto with the VideoReQuest sample program. Program the VRQ, DVD, Play, Stop, and Pause command to the appropriate receiver command.
Page 8 Appendix 1: Sony Changer Software Update The Sony changer has a bug in software versions under 1.5.10 (0095). unless this update is put into place: It will lock up How to check the software version of the Sony CD Changer: Press the I/O key and put the set in STAND-BY and then press keys on the remote in order as shown below. 1. “5” 2. “CLEAR” 3. "I/O" button (POWER ON/OFF) ## Version information ## appears on the monitor. SYScon Version 1.510 (0095) (if firmware is below 1.5.
Page 9 Appendix 2: Safety Procedures Please follow these safety procedures for a smooth installation and long product life. The warranty will be voided if these procedures are not followed. 1) Do not open the case of the product to prevent the risk of electric shock. 2) Do not modify any hardware or software of the product without written approval from ReQuest Multimedia. 3) Any servicing must only be done by ReQuest Multimedia. 4) Please install in a well ventilated area.
