Product Manual

ManualsBrandsZee Line ManualsAir Operated Oil Pumps3:1 Stub Air-Operated Oil Pump — 3.7 GPM

INSTRUCTIONS FOR USE

3:1 AIR OPERA TED OIL PUMP

Congratulations on your purchase of this world-class premium construction Air Operated Oil Pump.

STUB VERSION

PUMP

INLET

Features:

1.This is a 3:1 pump & will dispense media at a

pressure equaling little less than 3 times the Air

Inlet Pressure

2.Recommended for applications where the final

discharge point is 30 meters or less from the

pump

3.Precision engineered steel pump construction with

machined Aluminum air motor

4. CNC machined & 100% factory tested

Wetted Components:

Steel, Brass, Aluminum, Hi Nitrile Rubber,

Polyurethane & Turcite

Intended Use with :

ATF, Engine Oil, Gear Oil, Hydraulic Oil, Oils

upto SAE 130, Diesel, Kerosene etc.

Do Not Use with:

Corrosive media, solvents, acids, alkalis,

antifreeze, Waste Oil etc.

Air Inlet ¼” (F)

Pump Inlet 1” (F) on stub pump only

Pump Outlet ½” (F)

Working Pressure 30-145 PSI (2-10 BAR)***

Maximum Air

Pressure 150 PSI (10 BAR)***

Air Consumption 230 lt/min (61 GPM)

Discharge 14 lt/min (3.70 GPM)**

Noise Level 81 db

Maximum

Viscosity of Oil 130 SAE

** Measured at pump outlet when not connected with

any hose & an inlet pressure of 85 PSI (6 BAR ),

with SAE 30 oil at ambient temperature of 29°C &

Piece Count

1.Pump Assembly

2.Bung Nut*

3. Foot valve

4. FRL connecting nipple*

*not included on all models

+ only with stub pumps

varying sizes:

The ump comes in a choice of different lengths to suit drums of

DESCRIPTION

For use on a tank or with a mobile oil system.

Recommended when connecting a specially

made suction tube or hose assembly to the

pump inlet. Pump inlet is threaded 1” (F).

Such pumps may be supplied with or without

a Bung Nut. Suction tube inlet must be fitted

with a foot valve (non return valve)(included)

MODEL

STUB VERSION

1700RPAR

Summary of content (3 pages)

PAGE 1
INSTRUCTIONS FOR USE 3:1 AIR OPERA TED OIL PUMP 1700RPAR Congratulations on your purchase of this worldclass premium construction Air Operated Oil u Pmp. Features: 1.This is a 3:1 pump & will dispense media at a pressure equaling little less than 3 times the Air Inlet Pressure 2.Recommended for applications where the final discharge point is 30 meters or less from the pump 3.Precision engineered steel pump construction with machined Aluminum air motor 4.
PAGE 2
GETTING STARTED Before you start installing the pump, make sure the following are available: Clean Supply of Air : This is one of the most important for life of your pump. Make sure air quality is very good with no contaminants / moisture. This can be achieved by installing a Filter Unit in the air line , before the line is put into the Air inlet port on the Pump Regulator : Since compressed air may be used at many points in your shop, air pressure in the line will keep fluctuating.
PAGE 3
TROUBLESHOOTING Sr. Nr PROBLEM CAUSES REMEDY 1. Pump does not dispense fluid 1.Pump not able to create adequate suction 1. Make sure that media used has a viscosity of SAE 130 or lower .Make sure all threaded connections are air tight 2. Media level inside the drum may be too low. Change drum 3.Remove suction tube & clean strainer at pump inlet 4. Inlet Air Pressure must at least be 30 PSI (2 BAR).Increase inlet pressure 5. Open small drum plug on the drum 2.Drum is Empty 3.Pump inlet is blocked 4.