Specifications

ManualsBrandsZebra ManualsComputer equipmentZebraNet RXi Series

Table Of Contents

P1050133-005

ZebraNet

Wireless Quick Start

Guide

for

Xi™ Series, RXi™ Series,

PAX4™ Series, Z Series

, RZ™ Series,

HC100™, S4M™, 105SL™, 105SLPlus™,

ZT200™ Series, ZE500™Series, and

ZT400™ Series Printers

Summary of content (96 pages)

PAGE 1
ZebraNet Wireless Quick Start Guide ® for Xi™ Series, RXi™ Series, PAX4™ Series, Z Series®, RZ™ Series, HC100™, S4M™, 105SL™, 105SLPlus™, ZT200™ Series, ZE500™Series, and ZT400™ Series Printers P1050133-005
PAGE 2
Copyright and Liability Disclaimer © 2013 ZIH Corp. The copyrights in this manual and the software and/or firmware in the printer described therein are owned by ZIH Corp. and Zebra’s licensors. Unauthorized reproduction of this manual or the software and/ or firmware in the printer may result in imprisonment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.
PAGE 3
Contents 1 • About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Who Should Use This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 How This Document Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Document Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Contacts . . . . . . . . .
PAGE 4
Contents 105SL and 105SLPlus Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FCC Radiation Exposure Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Canadian DOC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brasil — Aviso da Anatel . . . . . . . . . . . . . . . . . . . . .
PAGE 5
Contents 110PAX4 and R110PAX4 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170PAX4 General Specifications .
PAGE 6
Contents 8 • Xi Series and RXi Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Select a Site for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Select a Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Provide Proper Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Allow Proper Space . . . .
PAGE 7
Contents 10 • ZE500 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Print Engine Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Select a Site for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
Contents ZT210, ZT220, and ZT230 Compliance Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FCC Radiation Exposure Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Canadian DOC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Industry Canada (IC) Warning . . . . . . . . . . . . . . . . . . . . .
PAGE 9
1 About This Document This section provides you with contact information, document structure and organization, and additional reference documents. Contents Who Should Use This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How This Document Is Organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 10
About This Document Who Should Use This Document Who Should Use This Document This guide is intended for use by someone who needs to configure and use a ZebraNet wireless print server for use with a supported printer. This guide supports the ZebraNet Wireless Print Server, the ZebraNet Wireless Plus Print Server, the ZebraNet Internal Wireless Plus Print Server, and the ZebraNet b/g Print Server. The firmware version required to operate your print server varies based on your printer.
PAGE 11
About This Document Document Conventions Document Conventions The following conventions are used throughout this document to convey certain information. Printer/Print Engine The term “printer” will be used throughout this document to refer to Zebra printers and print engines. Alternate Color (online only) Cross-references contain hot links to other sections in this guide. If you are viewing this guide online in .pdf format, you can click the cross-reference (blue text) to jump directly to its location.
PAGE 12
About This Document Contacts Contacts Technical Support via the Internet is available 24 hours per day, 365 days per year. Web Site: www.zebra.com E-mail Back Technical Library: E-mail address: emb@zebra.com Subject line: Emaillist Self Service Knowledge Base: www.zebra.com/knowledgebase Online Case Registration: www.zebra.
PAGE 13
2 Printer Setup This section provides the tasks that you must complete and the issues that you must consider before you load and configure your printer. Contents Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Cord Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connect the Printer to a Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 14
Printer Setup Before You Begin Before You Begin Review this checklist, and resolve any issues before you set up or use your wireless printer.  Unpack and Inspect the Printer Have you unpacked the printer and inspected it for damage? When you receive the printer, immediately unpack it and inspect for shipping damage. • Save all packing materials. • Check all exterior surfaces for damage. • Raise the media door, and inspect the media compartment for damage to components.
PAGE 15
Printer Setup Power Cord Specifications Power Cord Specifications Caution • For personnel and equipment safety, always use an approved three-conductor power cord specific to the region or country intended for installation. This cord must use an IEC 320 female connector and the appropriate region-specific, three-conductor grounded plug configuration. Depending on how your printer was ordered, a power cord may or may not be included.
PAGE 16
Printer Setup Connect the Printer to a Power Source Connect the Printer to a Power Source The power supply in the printer automatically detects the applied line voltage and works in the 100 to 240 VAC, 47 to 63 Hz range. The AC power cord must have a three-prong female connector on one end that plugs into the mating AC power connector at the rear of the printer. If a power cable was not included with your printer, refer to Power Cord Specifications on page 15.
PAGE 17
Printer Setup Select a Wired Data Communication Interface Select a Wired Data Communication Interface To configure your printer for wireless operation, you must first connect your printer using a wired data communication interface. Table 1 provides basic information about wired data communication interfaces. Not all interfaces may be available on your printer. Select an interface that is supported by both your printer and your computer or your Local Area Network (LAN).
PAGE 18
Printer Setup Select a Wired Data Communication Interface Data Cables and Wireless Cards You must supply all data cables or removeable radio cards for your application. (Some wireless print servers come with an integrated radio card.) Data Cables Ethernet cables do not require shielding, but all other data cables must be fully shielded and fitted with metal or metallized connector shells. Unshielded data cables may increase radiated emissions above the regulated limits.
PAGE 19
3 Wireless Configuration Use this section to configure your ZebraNet wireless print server for operation. For more detailed information, refer to the ZebraNet Wired and Wireless Print Servers User Guide. Important • A wireless option board must be installed on your printer before you can configure the printer to communicate using a wireless radio card. You may configure your printer for wireless operation in the following ways. This Quick Start Guide covers only the first option, the Connectivity Wizard.
PAGE 20
Wireless Configuration Configure Using the Connectivity Wizard Configure Using the Connectivity Wizard The ZebraNet Bridge Enterprise utility resides on the User CD for your printer and is available through http://www.zebra.com/software. ZebraNet Bridge Enterprise version 1.2.5 or later is required to configure the printer correctly for use.
PAGE 21
Wireless Configuration Configure Using the Connectivity Wizard • If you will save the file without sending it to the printer, you may select any available port. • If you select File:, you will be asked to browse to the location of the file you want to save. • If you select a serial port, the serial configuration information appears below the Choose Port list. If necessary, change the serial communication settings to match your printer’s settings.
PAGE 22
Wireless Configuration Configure Using the Connectivity Wizard 7. Select the type of printer you are using and then click Next. The wizard prompts for the wireless IP information.
PAGE 23
Wireless Configuration Configure Using the Connectivity Wizard 8. Enable the DHCP (dynamic) or static IP option. If you will be using... Complete the following steps... DHCP a. Select DHCP and click Next. b. Continue with step 9. Static a. Select Static. The IP settings fields are activated. a. Enter the IP Address, Default Gateway, and Subnet Mask for the wireless print server. b. Continue with step 9. 9. Click Next. The Wireless Settings window opens. 10. Enter the ESSID.
PAGE 24
Wireless Configuration Configure Using the Connectivity Wizard 11. From the drop-down, select your Security Mode. If you select… Then… None Continue with step 12. WEP 40-Bit WEP 128-Bit a. In the WEP Options section of the window, enter the EAP-TLS EAP-TTLS EAP-FAST WPA-EAP-TLS In the EAP section of the window, if necessary: a. Enter the Optional Private Key. b. Click Next and continue with step 12. PEAP LEAP WPA-EAP-TTLS WPA-PEAP WPA-LEAP In the General Security section of the window: a.
PAGE 25
Wireless Configuration Configure Using the Connectivity Wizard 12. Click Advanced Options in the Wireless Settings window. The Advanced Wireless Settings window opens. 13. Review the settings in the Advanced Wireless Settings window. Change the settings as necessary, and then click OK. The Wireless Settings window returns.
PAGE 26
Wireless Configuration Configure Using the Connectivity Wizard 14. Click Next. Based on your selections in the Wireless Setup Wizard, the program writes the appropriate ZPL commands and displays them for your review. If you selected… Then a dialog box similar to this displays.
PAGE 27
Wireless Configuration Configure Using the Connectivity Wizard 15. Determine if you will send the script immediately, or save it for use at a later time. To... Then... Complete setup by sending the ZPL script to the printer through the port selected at the beginning of this procedure a. Verify that the printer is connected to the computer through the port you selected. Note • For serial connections, use a serial null modem cable. b. If you have not already done so, turn on (I) the printer. c.
PAGE 28
Wireless Configuration Configure Using the Connectivity Wizard 16. Observe the wireless status on the printer’s control panel, and confirm that you have set up your printer for wireless connectivity. Printers that have an LCD display text or symbols (see Table 2 and Table 3). The HC100 printer does not have an LCD, so the wireless status is indicated by the control panel lights (see Table 4).
PAGE 29
Wireless Configuration Configure Using the Connectivity Wizard HC100 Wireless Status Indicator Lights Table 4 • HC100 Wireless Status Indicator Lights Wireless Status Indicator 12/10/2013 Meaning Steady Green The printer is associated with a wireless network. The signal strength is strong. Flashing Green The printer is NOT associated with a wireless network. The signal strength is strong. Steady Orange The printer is associated with a wireless network. The signal strength is weak.
PAGE 30
Wireless Configuration Configure Using the Connectivity Wizard Notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ ___________________________________________________________________
PAGE 31
4 105SL and 105SLPlus This section provides the features of and specifications for this printer. Note • Printer specifications are subject to change without notice. Contents Select a Site for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 105SL and 105SLPlus General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 105SL and 105SLPlus Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 32
105SL and 105SLPlus Select a Site for the Printer Select a Site for the Printer Consider the following when selecting an appropriate location for your printer. Select a Surface Select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (such as a computer), if necessary. The choices include a table, countertop, desk, or cart. For the printer’s weight and dimensions, see 105SL and 105SLPlus General Specifications on page 33.
PAGE 33
105SL and 105SLPlus 105SL and 105SLPlus General Specifications 105SL and 105SLPlus General Specifications Physical Specifications 105SL Dimensions U.S. Standard 105SLPlus Metric U.S. Standard Metric Height 15.5 in 394 mm 15.5 in 394 mm Width 10.2 in. 259 mm 10.31 in. 262 mm Depth 18.9 in. 480 mm 20.38 in. 517.5 mm Weight without options 55 lb 25 kg 50 lb 22.
PAGE 34
105SL and 105SLPlus 105SL and 105SLPlus Compliance Information 105SL and 105SLPlus Compliance Information Important • The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
PAGE 35
105SL and 105SLPlus 105SL and 105SLPlus Compliance Information Brasil — Aviso da Anatel Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados.
PAGE 36
105SL and 105SLPlus 105SL and 105SLPlus Compliance Information Mexico — NOM-121-SCT1-2009 Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxima de antena de [x] dB. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que [x] dB quedan prohibidas. La impedancia requerida de la antena es de [y] ohms.
PAGE 37
5 HC100 This section provides the features of and specifications for this printer. Note • Printer specifications are subject to change without notice. Contents Select a Site for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 HC100 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 HC100 Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 38
HC100 Select a Site for the Printer Select a Site for the Printer Consider the following when selecting an appropriate location for your printer. Select a Surface Select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (such as a computer), if necessary. The choices include a table, countertop, desk, or cart. For the printer’s weight and dimensions, see HC100 General Specifications on page 39.
PAGE 39
HC100 HC100 General Specifications HC100 General Specifications Physical Specifications Dimensions U.S. Standard Metric Height 7.0 in 178 mm Width 5.0 in. 127 mm Depth 9.5 in. 242 mm Clearance - amount of space needed above the printer to allow for loading a media cartridge 6 in. 153 mm Weight without options 3.1 lb. 1.4 kg Electrical Specifications Power General 100-240 VAC, 50-60 Hz external power supply Printer idle 5W Environmental Conditions for Operation and Storage U.S.
PAGE 40
HC100 HC100 Compliance Information HC100 Compliance Information Important • The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
PAGE 41
HC100 HC100 Compliance Information Brasil — Aviso da Anatel Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site da ANATEL http://www.anatel.
PAGE 42
HC100 HC100 Compliance Information Mexico — NOM-121-SCT1-2009 Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxima de antena de [x] dB. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que [x] dB quedan prohibidas. La impedancia requerida de la antena es de [y] ohms. This equipment has been designed to operate with the antennas that are listed below and for maximum antenna gain of {X} dB.
PAGE 43
6 PAX4 Series This section provides the features of and specifications for this printer. Note • Printer specifications are subject to change without notice. Contents Print Engine Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110PAX4 and R110PAX4 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170PAX4 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 44
PAX4 Series Print Engine Installation Print Engine Installation This section provides basic information for mounting the print engine into an applicator. The illustrations in this section show the print engine from different angles and include dimensions and clearance needs. Requirements Stability When the print engine is mounted, the complete assembly must be physically stable. When the print engine is loaded with ribbon and media, the equipment must not become physically unstable.
PAGE 45
PAX4 Series Select a Site for the Printer Select a Site for the Printer Consider the following when selecting an appropriate location for your printer. Stability When the print engine is mounted, the complete assembly must be physically stable. When the print engine is loaded with ribbon and media, the equipment must not become physically unstable.
PAGE 46
PAX4 Series Select a Site for the Printer Provide a Power Source Place the printer within a short distance of a power outlet that is easily accessible. Power Requirements Consider the current rating of the print engine during installation. When power is applied to the print engine and the enclosing equipment, an overload condition must not be created. Grounding Requirements Maintain reliable grounding of the print engine.
PAGE 47
PAX4 Series 110PAX4 and R110PAX4 General Specifications 110PAX4 and R110PAX4 General Specifications Physical 110PAX4/R110PAX4 Dimensions U.S. Standard Metric Height 11.8 in 300 mm Width 9.6 in. 245 mm Depth 16.4 in. 417 mm Weight 36 lb 16.
PAGE 48
PAX4 Series 170PAX4 General Specifications 170PAX4 General Specifications Physical 170PAX4 Dimensions U.S. Standard Metric Height 11.8 in 300 mm Width 9.6 in. 245 mm Depth 18.3 in. 465 mm Weight 35.5 lb 16.
PAGE 49
PAX4 Series PAX4 Compliance Information PAX4 Compliance Information Important • The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
PAGE 50
PAX4 Series PAX4 Compliance Information Brasil — Aviso da Anatel Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site da ANATEL http://www.
PAGE 51
PAX4 Series PAX4 Compliance Information Mexico — NOM-121-SCT1-2009 Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxima de antena de [x] dB. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que [x] dB quedan prohibidas. La impedancia requerida de la antena es de [y] ohms. This equipment has been designed to operate with the antennas that are listed below and for maximum antenna gain of {X} dB.
PAGE 52
PAX4 Series PAX4 Compliance Information Notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ _______________
PAGE 53
7 S4M This section provides the features of and specifications for this printer. Note • Printer specifications are subject to change without notice. Contents Select a Site for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 S4M General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 S4M Compliance Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 54
S4M Select a Site for the Printer Select a Site for the Printer Consider the following when selecting an appropriate location for your printer. Select a Surface Select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (such as a computer), if necessary. The choices include a table, countertop, desk, or cart. For the printer’s weight and dimensions, see S4M General Specifications on page 55.
PAGE 55
S4M S4M General Specifications S4M General Specifications Physical Specifications U.S. Standard Metric Height 11.6 in. 295 mm Width 10.7 in. 272 mm Depth 18.8 in. 477 mm Weight without options 27.2 lb 12.4 kg Dimensions Electrical Specifications Power General 100 to 240 VAC; 47 to 63 Hz 5 Amps (fused) Printer idle 8.
PAGE 56
S4M S4M Compliance Information S4M Compliance Information Important • The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
PAGE 57
S4M S4M Compliance Information Brasil — Aviso da Anatel Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site da ANATEL http://www.anatel.gov.
PAGE 58
S4M S4M Compliance Information Mexico — NOM-121-SCT1-2009 Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxima de antena de [x] dB. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que [x] dB quedan prohibidas. La impedancia requerida de la antena es de [y] ohms. This equipment has been designed to operate with the antennas that are listed below and for maximum antenna gain of {X} dB.
PAGE 59
8 Xi Series and RXi Series This section provides the features of and specifications for this printer. Note • Printer specifications are subject to change without notice. Contents Select a Site for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Xi4 and R110Xi4 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Xi Series and RXi Series Compliance Information. . . . . . . . . . . . . . . . . . . . .
PAGE 60
Xi Series and RXi Series Select a Site for the Printer Select a Site for the Printer Consider the following when selecting an appropriate location for your printer. Select a Surface Select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (such as a computer), if necessary. The choices include a table, countertop, desk, or cart. For the printer’s weight and dimensions, see Xi4 and R110Xi4 General Specifications on page 61.
PAGE 61
Xi Series and RXi Series Xi4 and R110Xi4 General Specifications Xi4 and R110Xi4 General Specifications Physical Specifications 110Xi4/R110Xi4 Dimensions 140Xi4 170Xi4 220Xi4 U.S. Standard Metric U.S. Standard Metric U.S. Standard Metric U.S. Standard Metric Height 15.5 in 393.7 mm 15.5 in 393.7 mm 15.5 in 393.7 mm 15.5 in 393.7 mm Width 10.31 in. 261.9 mm 11.31 in. 287.3 mm 13.31 in. 338.1 mm 15.81 in. 401.6 mm Depth 20.38 in. 517.5 mm 20.38 in. 517.5 mm 20.38 in. 517.
PAGE 62
Xi Series and RXi Series Xi Series and RXi Series Compliance Information Xi Series and RXi Series Compliance Information Important • The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables. FCC Compliance Statement This device complies with part 15 of the FCC Rules.
PAGE 63
Xi Series and RXi Series Xi Series and RXi Series Compliance Information Brasil — Aviso da Anatel Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados.
PAGE 64
Xi Series and RXi Series Xi Series and RXi Series Compliance Information Mexico — NOM-121-SCT1-2009 Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxima de antena de [x] dB. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que [x] dB quedan prohibidas. La impedancia requerida de la antena es de [y] ohms.
PAGE 65
9 Z Series and RZ Series This section provides the features of and specifications for this printer. Note • Printer specifications are subject to change without notice. Contents Select a Site for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Z Series and RZ Series General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Z Series and RZ Series Compliance Information. . . . . . . . . . . . . . . . . . . . . . . .
PAGE 66
Z Series and RZ Series Select a Site for the Printer Select a Site for the Printer Consider the following when selecting an appropriate location for your printer. Select a Surface Select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (such as a computer), if necessary. The choices include a table, countertop, desk, or cart. For the printer’s weight and dimensions, see Z Series and RZ Series General Specifications on page 67.
PAGE 67
Z Series and RZ Series Z Series and RZ Series General Specifications Z Series and RZ Series General Specifications Physical Specifications ZM400/RZ400 Dimensions ZM600/RZ600 U.S. Standard Metric U.S. Standard Metric Height 13.3 in. 338 mm 13.3 in. 338 mm Width 10.9 in. 278 mm 13.4 in. 341 mm Depth 18.7 in. 475 mm 18.7 in. 475 mm Weight (without options) 32.4 lbs. 15 kg 34.7 lbs.
PAGE 68
Z Series and RZ Series Z Series and RZ Series Compliance Information Z Series and RZ Series Compliance Information Important • The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables. FCC Compliance Statement This device complies with part 15 of the FCC Rules.
PAGE 69
Z Series and RZ Series Z Series and RZ Series Compliance Information Brasil — Aviso da Anatel Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados.
PAGE 70
Z Series and RZ Series Z Series and RZ Series Compliance Information Mexico — NOM-121-SCT1-2009 Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxima de antena de [x] dB. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que [x] dB quedan prohibidas. La impedancia requerida de la antena es de [y] ohms.
PAGE 71
10 ZE500 Series This section provides the features of and specifications for this printer. Note • Printer specifications are subject to change without notice. Contents Print Engine Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 ZE500 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 ZE500 Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 72
ZE500 Series Print Engine Installation Print Engine Installation This section provides basic information for mounting the print engine into an applicator. The illustrations in this section show the print engine from different angles and include dimensions and clearance needs. Requirements Stability When the print engine is mounted, the complete assembly must be physically stable. When the print engine is loaded with ribbon and media, the equipment must not become physically unstable.
PAGE 73
ZE500 Series Select a Site for the Printer Select a Site for the Printer Consider the following when selecting an appropriate location for your printer. Stability When the print engine is mounted, the complete assembly must be physically stable. When the print engine is loaded with ribbon and media, the equipment must not become physically unstable.
PAGE 74
ZE500 Series Select a Site for the Printer Provide a Power Source Place the printer within a short distance of a power outlet that is easily accessible. Power Requirements Consider the current rating of the print engine during installation. When power is applied to the print engine and the enclosing equipment, an overload condition must not be created. Grounding Requirements Maintain reliable grounding of the print engine.
PAGE 75
ZE500 Series ZE500 General Specifications ZE500 General Specifications Physical Dimensions ZE500-4 ZE500-6 U.S. Standard Metric U.S. Standard Metric Height 11.8 in 300 mm 11.8 in 300 mm Width 9.6 in. 245 mm 9.6 in. 245 mm Depth 14.95 in. 380 mm 17.23 in. 438 mm Weight 34 lb 15.4 kg 38 lb 17.
PAGE 76
ZE500 Series ZE500 Compliance Information ZE500 Compliance Information Important • The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
PAGE 77
ZE500 Series ZE500 Compliance Information Brasil — Aviso da Anatel Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações, consulte o site da ANATEL http://www.
PAGE 78
ZE500 Series ZE500 Compliance Information Mexico — NOM-121-SCT1-2009 Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan y para una ganancia máxima de antena de [x] dB. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que [x] dB quedan prohibidas. La impedancia requerida de la antena es de [y] ohms. This equipment has been designed to operate with the antennas that are listed below and for maximum antenna gain of {X} dB.
PAGE 79
11 ZT200 Series This section provides the features of and specifications for these printers. Note • Printer specifications are subject to change without notice. Contents Select a Site for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 ZT210, ZT220, and ZT230 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 ZT210, ZT220, and ZT230 Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 80
ZT210 / ZT220 / ZT230 Select a Site for the Printer Select a Site for the Printer Consider the following when selecting an appropriate location for your printer. Select a Surface Select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (such as a computer), if necessary. The choices include a table, countertop, desk, or cart. For the printer’s weight and dimensions, see ZT210, ZT220, and ZT230 General Specifications on page 81.
PAGE 81
ZT210 / ZT220 / ZT230 ZT210, ZT220, and ZT230 General Specifications ZT210, ZT220, and ZT230 General Specifications Physical Specifications ZT210 Dimensions ZT220 ZT230 U.S. Standard Metric U.S. Standard Metric U.S. Standard Metric Height 11 in. 28 cm 11 in. 28 cm 11 in 28 cm Width 9.5 in. 24 cm 9.5 in 24 cm 9.5 in 24 cm Depth 17 in. 28 cm 17 in 43 cm 17 in 43 cm Weight 20 lb 9 kg 17 lb 7.
PAGE 82
ZT210 / ZT220 / ZT230 ZT210, ZT220, and ZT230 Compliance Information ZT210, ZT220, and ZT230 Compliance Information Important • The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables. FCC Compliance Statement This device complies with part 15 of the FCC Rules.
PAGE 83
ZT210 / ZT220 / ZT230 ZT210, ZT220, and ZT230 Compliance Information Canadian DOC Compliance Statement Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This Class B digital apparatus complies with Canadian ICES-003. Industry Canada (IC) Warning Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 84
ZT210 / ZT220 / ZT230 ZT210, ZT220, and ZT230 Compliance Information European Regulatory Information Note • Member states in the EU with restrictive use for this device are crossed out. This device is also authorized for use in all EFTA member states (CH, IS, LI, NO). Japan Restricted Frequencies For 5.725 - 5.825 GHz, this frequency band will not be available in Japan. Taiwan Restricted Frequencies For 5.15 - 5.25 GHz, this frequency band will not be available in Taiwan.
PAGE 85
ZT210 / ZT220 / ZT230 ZT210, ZT220, and ZT230 Compliance Information NCC 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 According to "Administrative Regulations on Low Power Radio Waves Radiated Devices" Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well
PAGE 86
ZT210 / ZT220 / ZT230 ZT210, ZT220, and ZT230 Compliance Information WLAN Radio Specification 802.11 b • 2.4GHz • DSSS (DBPSK, DQPSK and CCK) • RF power 63 mW (ZebraNet n Print Server) 802.11 g • 2.4GHz • OFDM (16-QAM and 64-QAM with BPSK and QPSK) • RF power 63 mW (ZebraNet n Print Server) 802.11 n • 2.4GHz • OFDM (16-QAM and 64-QAM with BPSK and QPSK) • RF power 63 mW (ZebraNet n Print Server) 802.11 a/n • 5.15-5.25 GHz, 5.25-5.35 GHz, 5.47-5.725 GHz, 5.725-5.
PAGE 87
12 ZT400 Series This section provides the features of and specifications for this printer. Note • Printer specifications are subject to change without notice. Contents Select a Site for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 ZT400 Series General Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 ZT400 Series Compliance Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 88
ZT400 Series Select a Site for the Printer Select a Site for the Printer Consider the following when selecting an appropriate location for your printer. Select a Surface Select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (such as a computer), if necessary. The choices include a table, countertop, desk, or cart. For the printer’s weight and dimensions, see ZT400 Series General Specifications on page 89.
PAGE 89
ZT400 Series ZT400 Series General Specifications ZT400 Series General Specifications Physical Specifications ZT410 Dimensions ZT420 U.S. Standard Metric U.S. Standard Metric Height 12.8 in 325 mm 12.8 in 325 mm Width 10.7 in. 272 mm 13.2 in. 335 mm Depth 19.7 in. 500 mm 19.7 in. 500 mm Weight (without options) 36 lbs. 16 kg 40 lbs. 18 kg Electrical Specifications Power ZT410 ZT420 General 100 to 240VAC; 47 to 63 Hz 100 to 240VAC; 47 to 63 Hz 118.7 W 220.0 W 6.0 W 6.
PAGE 90
ZT400 Series ZT400 Series Compliance Information ZT400 Series Compliance Information Important • The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with Shielded Communication Cables. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
PAGE 91
ZT400 Series ZT400 Series Compliance Information Industry Canada (IC) Warning Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : • L’appareil ne doit pas produire de brouillage, et • L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
PAGE 92
ZT400 Series ZT400 Series Compliance Information European Regulatory Information Note • Member states in the EU with restrictive use for this device are crossed out. This device is also authorized for use in all EFTA member states (CH, IS, LI, NO). Japan Restricted Frequencies For 5.725 - 5.825 GHz, this frequency band will not be available in Japan. Taiwan Restricted Frequencies For 5.15 - 5.25 GHz, this frequency band will not be available in Taiwan.
PAGE 93
ZT400 Series ZT400 Series Compliance Information NCC 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 According to "Administrative Regulations on Low Power Radio Waves Radiated Devices" Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a
PAGE 94
ZT400 Series ZT400 Series Compliance Information WLAN Radio Specification 802.11 b • 2.4GHz • DSSS (DBPSK, DQPSK and CCK) • RF power 63 mW (ZebraNet n Print Server) 802.11 g • 2.4GHz • OFDM (16-QAM and 64-QAM with BPSK and QPSK) • RF power 63 mW (ZebraNet n Print Server) 802.11 n • 2.4GHz • OFDM (16-QAM and 64-QAM with BPSK and QPSK) • RF power 63 mW (ZebraNet n Print Server) 802.11 a/n • 5.15-5.25 GHz, 5.25-5.35 GHz, 5.47-5.725 GHz, 5.725-5.
PAGE 95
PAGE 96
Zebra Technologies Corporation Zebra Technologies Corporation 475 Half Day Road, Suite 500 Lincolnshire, IL 60069 USA T: +1 847 634 6700 Toll-free +1 866 230 9494 F: +1 847 913 8766 Zebra Technologies Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire, SL8 5XF, UK T: +44 (0)1628 556000 F: +44 (0)1628 556001 Zebra Technologies Asia Pacific, LLC 120 Robinson Road #06-01 Parakou Building Singapore 068913 T: +65 6858 0722 F: +65 6885 0838 http://www.zebra.com © 2013 ZIH Corp.