User Manual
Table Of Contents
- Contents
- About this Guide
- Introducing the ZD411D
- ZD411D Features
- Controls and Indicators
- Installing Hardware Options
- Field Installable ZD411D Accessories and Options
- Printer Connectivity Modules
- Power Failure Recovery Mode Jumper (OFF by Default)
- Configuring Wired Connectivity Options and Power Failure Recovery Mode
- Installing the Wireless Connectivity Module
- Media Handling Options
- Installing Dispense, Cut, and Tear Media Handling Options
- Media Roll Core Size Adapters
- Installing the Attached Battery Base Options
- Installing the Battery into the Attached Power Base
- ZD411D Printer Setup
- ZD411D Printer Setup Overview
- Select a Location for the Printer
- Pre-Install Printer Options and Connectivity Modules
- Attaching Printer Power
- Getting Ready to Print
- Preparing and Handling Labels and Media
- Media Storage Tips
- Loading Roll Media in the ZD411D Printer
- How to Load Roll Media – ZD411D
- Using the Movable Sensor
- Adjusting the Movable Sensor for Black Marks or Notches
- Adjusting the Movable Sensor for Web/Gap Sensing
- How to Load Roll Media - Continued
- Run a SmartCal Media Calibration
- Print a Configuration Report to Test Printing
- Detecting a Media Out Condition
- Connecting to the Printer
- Pre-install Windows Printer Drivers
- Interface Cable Requirements
- USB Interface (Device)
- Serial Interface
- Ethernet (LAN, RJ-45)
- ZD411D Printer Setup Overview
- Setup for Windows
- Print Operations
- Thermal Printing Basic Setting and Operations
- Printing on Fan-Fold Media
- Using the Label Dispenser Option
- Printing with Externally Mounted Roll Media
- Printing with the Attached Battery Base and Battery Option
- Printer Fonts
- Zebra ZKDU – Printer Accessory
- Zebra Basic Interpreter (ZBI) 2.0
- Setting the Power Failure Recovery Mode Jumper
- Maintaining the Printer
- Troubleshooting
- Onboard Printer Tools
- Printer Diagnostics
- SmartCal Media Calibration
- Printing a Configuration Report (CANCEL Self Test)
- Printer Network (and Bluetooth) Configuration Report
- Resetting Printer Factory Defaults (PAUSE + FEED Self Test)
- Resetting Network Factory Defaults (PAUSE + CANCEL Self Test)
- Generating a Print Quality Report (FEED self-test)
- Activating Advanced Mode
- Factory Test Modes
- Using the Reset Button
- Running a Communication Diagnostics Test
- Sensor Profile Report
- Universal Serial Bus (USB) Interface
- Serial Port Interface
- Types of Thermal Media
- ZD411D Printer Dimensions
- ZPL Configuration
Installing Hardware Options
Installing Hardware Options
This section assists you in installing common printer connectivity modules and media handling options.
IMPORTANT:
To simplify and speed up the setup process, install all connectivity modules and media handling
options before setting up and using the printer for the first time.
It is strongly recommended that you update the printer’s firmware after the printer has completed
the setup process. Many of these options have internal firmware that requires an update to
operate properly with the printer’s Main Logic Board’s installed firmware version.
Field Installable ZD411D Accessories and Options
The printer supports a wide variety of user upgrade kits forconnectivity, media handling, and power
options.
Printer Connectivity Modules
The connectivity module access door must be removed prior to installing the following options – Accessing
the Connectivity Module Slot.
• Wireless Connectivity Module - Installing the Wireless Connectivity Module
• Wi-Fi 802.11ac,Bluetooth 4.2,BTLE 5, and MFi 3.0
Media Handling Options
The printer standard bezel must be removed prior to installing the following options – Removing the
Standard Bezel.
• Label Dispenser (Peel-Off Liner and Present Label for Operator) - Installing the Label Dispenser
• General Purpose Media Cutter – Installing the Standard Media Cutter
• Media Roll Adapters for 38.1 mm (1.5 in.), 50.8 mm (2.0 in.), or 76.2 mm (3.0 in.)inner diametermedia
cores - Media Roll Core Size Adapters
Power Base Options
The printer supports a power base field upgrade kit for the printers.
• Battery Power Base (battery pack sold separately) – Installing the Attached Battery Base Options
• Battery Pack (battery power base sold separately) – Installing the Battery into the Attached Power Base
39