User Manual
Table Of Contents
- Contents
- About this Guide
- Introducing the ZD411D
- ZD411D Features
- Controls and Indicators
- Installing Hardware Options
- Field Installable ZD411D Accessories and Options
- Printer Connectivity Modules
- Power Failure Recovery Mode Jumper (OFF by Default)
- Configuring Wired Connectivity Options and Power Failure Recovery Mode
- Installing the Wireless Connectivity Module
- Media Handling Options
- Installing Dispense, Cut, and Tear Media Handling Options
- Media Roll Core Size Adapters
- Installing the Attached Battery Base Options
- Installing the Battery into the Attached Power Base
- ZD411D Printer Setup
- ZD411D Printer Setup Overview
- Select a Location for the Printer
- Pre-Install Printer Options and Connectivity Modules
- Attaching Printer Power
- Getting Ready to Print
- Preparing and Handling Labels and Media
- Media Storage Tips
- Loading Roll Media in the ZD411D Printer
- How to Load Roll Media – ZD411D
- Using the Movable Sensor
- Adjusting the Movable Sensor for Black Marks or Notches
- Adjusting the Movable Sensor for Web/Gap Sensing
- How to Load Roll Media - Continued
- Run a SmartCal Media Calibration
- Print a Configuration Report to Test Printing
- Detecting a Media Out Condition
- Connecting to the Printer
- Pre-install Windows Printer Drivers
- Interface Cable Requirements
- USB Interface (Device)
- Serial Interface
- Ethernet (LAN, RJ-45)
- ZD411D Printer Setup Overview
- Setup for Windows
- Print Operations
- Thermal Printing Basic Setting and Operations
- Printing on Fan-Fold Media
- Using the Label Dispenser Option
- Printing with Externally Mounted Roll Media
- Printing with the Attached Battery Base and Battery Option
- Printer Fonts
- Zebra ZKDU – Printer Accessory
- Zebra Basic Interpreter (ZBI) 2.0
- Setting the Power Failure Recovery Mode Jumper
- Maintaining the Printer
- Troubleshooting
- Onboard Printer Tools
- Printer Diagnostics
- SmartCal Media Calibration
- Printing a Configuration Report (CANCEL Self Test)
- Printer Network (and Bluetooth) Configuration Report
- Resetting Printer Factory Defaults (PAUSE + FEED Self Test)
- Resetting Network Factory Defaults (PAUSE + CANCEL Self Test)
- Generating a Print Quality Report (FEED self-test)
- Activating Advanced Mode
- Factory Test Modes
- Using the Reset Button
- Running a Communication Diagnostics Test
- Sensor Profile Report
- Universal Serial Bus (USB) Interface
- Serial Port Interface
- Types of Thermal Media
- ZD411D Printer Dimensions
- ZPL Configuration
ZD411D Features
Zebra Print Touch
With theZebra Print Touch feature,you can use a Near Field Communication (NFC)-enabled device such
as a smartphone or tablet to scan the Print Touch logo and pair the device to the printer.
Print Touch is available on models with a factory-installed low-power Bluetooth. This capability enables
you to use your device to provide information for which you are prompted and then print a label using that
information.
NOTE: Some mobile devices may not support NFC communication with the printer until you
configure the required NFC settings in your device. If you encounter difficulties, consult your
service provider or your smart device manufacturer for more information.
Figure 7Zebra Print Touch NFC Reader Activation Location
Data Included in the Encoded NFC Tag
• A URL for a Zebra QuickHelp style support web page
• The printer's Bluetooth Low Energy MAC address
• The printer's Bluetooth Classic MAC address (if present)
• The printer's Wi-Fi (WLAN) MAC address (if present)
• The printer's Ethernet (LAN) MAC address (if present)
• The printer SKU – example ZD42122-D01W01EZ
• The printer's serial number
Uses for the Print Touch feature (NFC tag)
• Facilitate Bluetooth pairing with a compatible mobile device
• Launch an application
• Launch a mobile browser to a web page
29