User Manual
Table Of Contents
- Contents
- About this Guide
- Introducing the ZD411D
- ZD411D Features
- Controls and Indicators
- Installing Hardware Options
- Field Installable ZD411D Accessories and Options
- Printer Connectivity Modules
- Power Failure Recovery Mode Jumper (OFF by Default)
- Configuring Wired Connectivity Options and Power Failure Recovery Mode
- Installing the Wireless Connectivity Module
- Media Handling Options
- Installing Dispense, Cut, and Tear Media Handling Options
- Media Roll Core Size Adapters
- Installing the Attached Battery Base Options
- Installing the Battery into the Attached Power Base
- ZD411D Printer Setup
- ZD411D Printer Setup Overview
- Select a Location for the Printer
- Pre-Install Printer Options and Connectivity Modules
- Attaching Printer Power
- Getting Ready to Print
- Preparing and Handling Labels and Media
- Media Storage Tips
- Loading Roll Media in the ZD411D Printer
- How to Load Roll Media – ZD411D
- Using the Movable Sensor
- Adjusting the Movable Sensor for Black Marks or Notches
- Adjusting the Movable Sensor for Web/Gap Sensing
- How to Load Roll Media - Continued
- Run a SmartCal Media Calibration
- Print a Configuration Report to Test Printing
- Detecting a Media Out Condition
- Connecting to the Printer
- Pre-install Windows Printer Drivers
- Interface Cable Requirements
- USB Interface (Device)
- Serial Interface
- Ethernet (LAN, RJ-45)
- ZD411D Printer Setup Overview
- Setup for Windows
- Print Operations
- Thermal Printing Basic Setting and Operations
- Printing on Fan-Fold Media
- Using the Label Dispenser Option
- Printing with Externally Mounted Roll Media
- Printing with the Attached Battery Base and Battery Option
- Printer Fonts
- Zebra ZKDU – Printer Accessory
- Zebra Basic Interpreter (ZBI) 2.0
- Setting the Power Failure Recovery Mode Jumper
- Maintaining the Printer
- Troubleshooting
- Onboard Printer Tools
- Printer Diagnostics
- SmartCal Media Calibration
- Printing a Configuration Report (CANCEL Self Test)
- Printer Network (and Bluetooth) Configuration Report
- Resetting Printer Factory Defaults (PAUSE + FEED Self Test)
- Resetting Network Factory Defaults (PAUSE + CANCEL Self Test)
- Generating a Print Quality Report (FEED self-test)
- Activating Advanced Mode
- Factory Test Modes
- Using the Reset Button
- Running a Communication Diagnostics Test
- Sensor Profile Report
- Universal Serial Bus (USB) Interface
- Serial Port Interface
- Types of Thermal Media
- ZD411D Printer Dimensions
- ZPL Configuration
Print Operations
Print width may be set by:
• The Windows printer driver or application software such as ZebraDesigner™.
• Controlling printer operations with ZPL programming; refer to the Print Width (^PW) command (consult
your ZPL Programming Guide).
• See Using the Manual Print Width Adjustment on page 155.
Related ZPL command(s):
^PW
SGD command used:
ezpl.print_width
Printer web page:
View and Modify Printer Settings > Media Setup > Print Width
Replacing Supplies while Using the Printer
If media (labels, receipts, tags, tickets, etc.) run out while printing, leave the printer power on while
reloading media. After you load a new roll of media, press the FEED button to resync and restart printing.
NOTE: Do not turn the printer off to replace the printer media. Dataloss results if you turn off
the printer while printing. By maintaining printer power, printjobs in progress can resume and
complete if a single printout or a batchprint job.
Pressthe FEED button once after reloading media initiates a media resync to the beginning of label.
Pressing the PAUSE will resume the print job in most cases.
Press the FEED buttonafter the media has been resynced or calibratedand the printer's default setting is
to reprint the last label image in the printer.
Printing on Fan-Fold Media
The printer can use fan-fold media via a media access slot in the rear of the printer.
1. Remove any roll media from the printer.
105