User Manual
Table Of Contents
- Copyright
- Terms of Use
- About
- Contents
- Introduction
- Printer Features
- Printer Features
- Inside the ZD620 Dual Capacity Ribbon Roll Printer
- Inside the ZD620 and ZD420 Direct Thermal Printers
- Inside the ZD420 Ribbon Cartridge Printer
- Label Dispenser Option (field installable) - All Models
- Cutter Option (field installable) - All Models
- Linerless Media Tear-Off Option (Direct Thermal Models Only)
- Linerless Cutter Option (Direct Thermal Models Only)
- Identifying Platen Drive Rollers Types
- Printer Power Supply Options
- ZD620 and ZD420 Locking Printer Features
- Zebra Print Touch
- Printer Features
- Install Hardware Options
- Field Installable printer Accessories and Options
- Printer Connectivity Modules
- Media Handling Options
- Installing the Attached Power Supply Base Options
- Controls and Indicators
- Printer Configuration Menus
- Setup
- Printer Setup Overview
- Select a Location for the Printer
- Install Printer Options and Connectivity Modules
- Attaching Power
- Getting Ready to Print
- Loading Roll Media
- Loading Thermal Transfer Roll Ribbon
- Loading the ZD420 Ribbon Cartridge
- Run a SmartCal Media Calibration
- Test Printing with the Configuration Report
- Detecting a Media Out Condition
- Detecting a Ribbon Out Condition
- Connecting your Printer to a Computer
- Wi-Fi and Bluetooth Classic Wireless Connectivity Option
- Setup for Windows® OS
- Print Operations
- Thermal Printing
- Determining Your Printer’s Configuration Settings
- Select a Print Mode
- Adjusting the Print Quality
- Darkness Control
- Adjusting the Print Width
- Printing on Fan-Fold Media
- Printing with Externally Mounted Roll Media
- Using the Label Dispenser Option
- Using the Linerless Options
- Sending Files to the Printer
- Printer Fonts
- EPL Line Mode - Direct Thermal Printers only
- Zebra® ZKDU — Printer Accessory
- ZD620 and ZD420 Locking Printer Option
- ZBI 2.0™ — Zebra Basic Interpreter
- Setting the Power Failure Recovery Mode Jumper
- USB Host Port and Link-OS Demonstration Examples
- USB Host
- USB Host and Printer Usage Examples
- Items Required for the USB Host Exercises
- Files for Completing the Exercises
- Exercise 1: Copy Files to a USB Flash Drive and Perform USB Mirror
- Exercise 2: Print a Label Format from a USB Flash Drive
- Exercise 3: Copy Files to/from a USB Flash Drive
- Exercise 4: Enter Data for a Stored File with a USB Keyboard and Print a Label
- Using the USB Hosts Port and the NFC Capabilities
- Maintenance
- Troubleshooting
- Resolving Alerts and Errors
- Resolving Print Issues
- Communication Issues
- Miscellaneous Issues
- Tools
- Printer Diagnostics
- Power-On Self Test
- SmartCal Media Calibration
- Configuration Report (CANCEL Self Test)
- Printer Network (and Bluetooth) Configuration Report
- Print Quality Report (FEED self test)
- Reset Printer Factory Defaults (PAUSE + FEED Self Test)
- Reset Network Factory Defaults (PAUSE + CANCEL Self Test)
- Reset Button
- Communication Diagnostics Test
- Sensor Profile
- Advanced Mode
- Factory Test Modes
- Printer Diagnostics
- Interface Connector Wiring
- Dimensions
- Media
- ZPL Configuration
118
Printer Configuration Menus
IP PORT
Description: This printer setting refers to the internal wired print servers port number that
the TCP print service is listening on. Normal TCP communications from the host should be
directed to this port.
SGD command used: internal_wired.ip.port
Printer Web page: View and Modify Printer Settings > Network Communications Setup >
TCP/IP Settings
NETWORK
—
ACTIVE PRINT SERVER
—
PRIMARY NETWORK
—
WIRED IP ADDRESS
—
WIRED SUBNET MASK
—
WIRED GATEWAY
—
WIRED IP PROTOCOL
—
WIRED MAC ADDRESS
—
WLAN IP ADDRESS
—
WLAN SUBNET MASK
—
WLAN GATEWAY
—
WLAN IP PROTOCOL
—
WLAN MAC ADDRESS
—
ESSID
—
CHANNEL
—
SIGNAL
—
IP PORT
—
IP ALTERNATE PORT
—
PRINT INFORMATION
—
RESET NETWORK
—
VISIBILITY AGENT
—
LOAD DEFAULTS