User Manual
Table Of Contents
- Copyright
- Terms of Use
- About
- Contents
- Introduction
- Printer Features
- Printer Features
- Inside the ZD620 Dual Capacity Ribbon Roll Printer
- Inside the ZD620 and ZD420 Direct Thermal Printers
- Inside the ZD420 Ribbon Cartridge Printer
- Label Dispenser Option (field installable) - All Models
- Cutter Option (field installable) - All Models
- Linerless Media Tear-Off Option (Direct Thermal Models Only)
- Linerless Cutter Option (Direct Thermal Models Only)
- Identifying Platen Drive Rollers Types
- Printer Power Supply Options
- ZD620 and ZD420 Locking Printer Features
- Zebra Print Touch
- Printer Features
- Install Hardware Options
- Field Installable printer Accessories and Options
- Printer Connectivity Modules
- Media Handling Options
- Installing the Attached Power Supply Base Options
- Controls and Indicators
- Printer Configuration Menus
- Setup
- Printer Setup Overview
- Select a Location for the Printer
- Install Printer Options and Connectivity Modules
- Attaching Power
- Getting Ready to Print
- Loading Roll Media
- Loading Thermal Transfer Roll Ribbon
- Loading the ZD420 Ribbon Cartridge
- Run a SmartCal Media Calibration
- Test Printing with the Configuration Report
- Detecting a Media Out Condition
- Detecting a Ribbon Out Condition
- Connecting your Printer to a Computer
- Wi-Fi and Bluetooth Classic Wireless Connectivity Option
- Setup for Windows® OS
- Print Operations
- Thermal Printing
- Determining Your Printer’s Configuration Settings
- Select a Print Mode
- Adjusting the Print Quality
- Darkness Control
- Adjusting the Print Width
- Printing on Fan-Fold Media
- Printing with Externally Mounted Roll Media
- Using the Label Dispenser Option
- Using the Linerless Options
- Sending Files to the Printer
- Printer Fonts
- EPL Line Mode - Direct Thermal Printers only
- Zebra® ZKDU — Printer Accessory
- ZD620 and ZD420 Locking Printer Option
- ZBI 2.0™ — Zebra Basic Interpreter
- Setting the Power Failure Recovery Mode Jumper
- USB Host Port and Link-OS Demonstration Examples
- USB Host
- USB Host and Printer Usage Examples
- Items Required for the USB Host Exercises
- Files for Completing the Exercises
- Exercise 1: Copy Files to a USB Flash Drive and Perform USB Mirror
- Exercise 2: Print a Label Format from a USB Flash Drive
- Exercise 3: Copy Files to/from a USB Flash Drive
- Exercise 4: Enter Data for a Stored File with a USB Keyboard and Print a Label
- Using the USB Hosts Port and the NFC Capabilities
- Maintenance
- Troubleshooting
- Resolving Alerts and Errors
- Resolving Print Issues
- Communication Issues
- Miscellaneous Issues
- Tools
- Printer Diagnostics
- Power-On Self Test
- SmartCal Media Calibration
- Configuration Report (CANCEL Self Test)
- Printer Network (and Bluetooth) Configuration Report
- Print Quality Report (FEED self test)
- Reset Printer Factory Defaults (PAUSE + FEED Self Test)
- Reset Network Factory Defaults (PAUSE + CANCEL Self Test)
- Reset Button
- Communication Diagnostics Test
- Sensor Profile
- Advanced Mode
- Factory Test Modes
- Printer Diagnostics
- Interface Connector Wiring
- Dimensions
- Media
- ZPL Configuration
117
Printer Configuration Menus
SIGNAL
Description: View the wireless signal strength when the wireless network is active and
authenticated.
SGD command used: wlan.signal_strength
Printer Web page: View and Modify Printer Settings
> Network Communications Setup >
Wireless Setup
NETWORK
—
ACTIVE PRINT SERVER
—
PRIMARY NETWORK
—
WIRED IP ADDRESS
—
WIRED SUBNET MASK
—
WIRED GATEWAY
—
WIRED IP PROTOCOL
—
WIRED MAC ADDRESS
—
WLAN IP ADDRESS
—
WLAN SUBNET MASK
—
WLAN GATEWAY
—
WLAN IP PROTOCOL
—
WLAN MAC ADDRESS
—
ESSID
—
CHANNEL
—
SIGNAL
—
IP PORT
—
IP ALTERNATE PORT
—
PRINT INFORMATION
—
RESET NETWORK
—
VISIBILITY AGENT
—
LOAD DEFAULTS