MP6000 BAR CODE PROGRAMMING GUIDE
MP6000 BAR CODE PROGRAMMING GUIDE 72E-172633-04 Revision A November 2014
ii MP6000 BAR CODE PROGRAMMING GUIDE No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original guide are listed below: Change Date Description -01 Rev. A 6/2013 Initial Release. -02 Rev. A 5/2014 Added: - New software information - Aux scanner parameters - RS-232 NCR and Datalogic information - Dual Cable Scale bar codes - Reset button - Third Party Scale parameters. -03 Rev. A 7/2014 Added: - New parameters...
iv MP6000 BAR CODE PROGRAMMING GUIDE
TABLE OF CONTENTS Warranty ......................................................................................................................................... ii Revision History .............................................................................................................................. iii About This Guide Introduction ..................................................................................................................................... Chapter Descriptions ...........
vi MP6000 BAR CODE PROGRAMMING GUIDE Chapter 2: RS-232 INTERFACE BAR CODES Introduction .................................................................................................................................... RS-232 Parameter Defaults ........................................................................................................... RS-232 Host Parameters ............................................................................................................... RS-232 Host Types ..
TABLE OF CONTENTS Chapter 5: USER PREFERENCES & MISCELLANEOUS OPTIONS Introduction .................................................................................................................................... Scanning Sequence Examples ...................................................................................................... Errors While Scanning ...................................................................................................................
viii MP6000 BAR CODE PROGRAMMING GUIDE Bar Code Auto Interlock Mode ................................................................................................. Bar Code Hold Off Mode .......................................................................................................... Sensormatic Scan Enable Interlock Mode ............................................................................... Checkpoint Bar Code Interlock Mode ............................................................
TABLE OF CONTENTS Decode UPC/EAN/JAN Supplementals ................................................................................... User-Programmable Supplementals ........................................................................................ UPC/EAN Redundancy ............................................................................................................ UPC/EAN/JAN Supplemental Redundancy .............................................................................
x MP6000 BAR CODE PROGRAMMING GUIDE Convert I 2 of 5 to EAN-13 ....................................................................................................... Interleaved 2 of 5 Stitching ...................................................................................................... Interleaved 2 of 5 Stitching Security Level ............................................................................... Interleaved 2 of 5 Marginless Mode ....................................................
TABLE OF CONTENTS xi Redundancy Level 4 ................................................................................................................ Security Level ................................................................................................................................ Intercharacter Gap Size ........................................................................................................... Macro PDF Features ..............................................................
xii MP6000 BAR CODE PROGRAMMING GUIDE Appendix D: NUMERIC BAR CODES Numeric Bar Codes ....................................................................................................................... 0 ............................................................................................................................................... 1 ............................................................................................................................................... 2 ..........
ABOUT THIS GUIDE Introduction The MP6000 Bar Code Programming Guide includes the programming bar codes to configure the MP6000. Chapter Descriptions • Chapter 1, USB INTERFACE BAR CODES provides bar codes to set up the bioptic scanner with a USB host. • Chapter 2, RS-232 INTERFACE BAR CODES provides bar codes to set up the bioptic scanner with an RS-232 host, such as point-of-sale devices, host computers, or other devices with an available RS-232 port.
xiv MP6000 BAR CODE PROGRAMMING GUIDE • Appendix A, STANDARD DEFAULT PARAMETERS provides a table of all host devices and miscellaneous scanner defaults. • Appendix B, PROGRAMMING REFERENCE provides a table of AIM code identifiers, ASCII character conversions, and keyboard maps. • Appendix C, SAMPLE BAR CODES includes sample bar codes of various code types. • Appendix D, NUMERIC BAR CODES includes the numeric bar codes to scan for parameters requiring specific numeric values.
ABOUT THIS GUIDE xv Related Documents • MP6000 Integrator Guide, p/n 72E-172632-xx, provides installation information, interface setups, scale calibration procedure, beeper and LED indicators, warning and error messages, and information about using the MP6000. • Advanced Data Formatting Programmer Guide (ADF), p/n 72E-69680-xx, provides ADF information and the bar codes necessary to customize data before transmission to a host. For the latest version of this guide and all guides, go to: http://www.
xvi MP6000 BAR CODE PROGRAMMING GUIDE
CHAPTER 1 USB INTERFACE BAR CODES Introduction This chapter includes the programming bar codes for the USB host interface. The MP6000 connects directly to a USB host, or a powered USB hub. An additional power supply is required (PWRS-14000-148R). Only a USB Power Plus host (IBM registers) can power the MP6000 using a Power Plus cable, with an external power supply.
1-2 MP6000 BAR CODE PROGRAMMING GUIDE USB Parameter Defaults Table 1-1 lists the defaults for USB host parameters. To change any option, scan the appropriate bar code(s) provided in the Parameter Descriptions section beginning on page 1-3. NOTE See Appendix A, STANDARD DEFAULT PARAMETERS for all user preferences, hosts, symbologies, and miscellaneous default parameters.
USB INTERFACE BAR CODES 1-3 USB Host Parameters USB Device Type Select the desired USB device type from the following options. • * IBM Table-top USB • IBM Hand-held USB • IBM OPOS (IBM Hand-held USB with Full Scan Disable) • HID Keyboard Emulation • CDC COM Port Emulation. • Symbol Native API (SNAPI) NOTE 1. When changing USB device types, the MP6000 automatically resets and issues the standard startup beep sequences. 2.
1-4 MP6000 BAR CODE PROGRAMMING GUIDE USB Device Type (continued) IBM Hand-held USB
USB INTERFACE BAR CODES USB Device Type (continued) IBM OPOS (IBM Hand-held USB with Full Scan Disable) 1-5
1-6 MP6000 BAR CODE PROGRAMMING GUIDE USB Device Type (continued) When the HID Keyboard host is selected, and the MP6000 has auxiliary scanners connected, use ADF rules to program the auxiliary scanners to add a 500 msec pause to the end of the data to prevent the interleaving of bar code data from multiple scanners. This works with standard RS-232, and SSI over RS-232 (with the Send Raw Decode Data setting).
USB INTERFACE BAR CODES USB Device Type (continued) CDC COM Port Emulation 1-7
1-8 MP6000 BAR CODE PROGRAMMING GUIDE USB Device Type (continued) Symbol Native API (SNAPI) Interface
USB INTERFACE BAR CODES 1-9 USB Country Keyboard Types - Country Codes Scan the bar code corresponding to the keyboard type from the following options. This setting applies only to the USB HID Keyboard Emulation device. Options: • *North American Standard USB Keyboard • German Windows • French Windows • French Canadian Windows 95/98 • French Canadian Windows 2000/XP. NOTE When changing USB country keyboard types the digital scanner automatically resets and issues the standard startup beep sequences.
1 - 10 MP6000 BAR CODE PROGRAMMING GUIDE USB Country Keyboard Types - Country Codes (continued) German Windows
USB INTERFACE BAR CODES 1 - 11 USB Country Keyboard Types - Country Codes (continued) French Windows
1 - 12 MP6000 BAR CODE PROGRAMMING GUIDE USB Country Keyboard Types - Country Codes (continued) French Canadian Windows 95/98
USB INTERFACE BAR CODES 1 - 13 USB Country Keyboard Types - Country Codes (continued) French Canadian Windows 2000/XP
1 - 14 MP6000 BAR CODE PROGRAMMING GUIDE USB Keystroke Delay This parameter sets the delay, in milliseconds, between emulated keystrokes. Scan the appropriate bar code from the following options to increase the delay when hosts require a slower transmission of data. Options: • *No Delay • Medium Delay (20 msec) • Long Delay (40 msec).
USB INTERFACE BAR CODES 1 - 15 USB Keystroke Delay (continued) Medium Delay (20 msec)
1 - 16 MP6000 BAR CODE PROGRAMMING GUIDE USB Keystroke Delay (continued) Long Delay (40 msec)
USB INTERFACE BAR CODES 1 - 17 Simulated Caps Lock Enable this to invert upper and lower case characters on the bar code as if the Caps Lock state is enabled on the keyboard. This inversion occurs regardless of the keyboard’s Caps Lock state. Note that this only applies to alpha characters. Options: • *Disable Simulated Caps Lock • Enable Simulated Caps Lock.
1 - 18 MP6000 BAR CODE PROGRAMMING GUIDE Simulated Caps Lock (continued) Enable Simulated Caps Lock
USB INTERFACE BAR CODES 1 - 19 USB CAPS Lock Override This option applies only to the HID Keyboard Emulation device. Enable this to preserve the case of the data regardless of the state of the Caps Lock key. This setting is always enabled for the Japanese, Windows (ASCII) keyboard type and can not be disabled. Options: • *Do Not Override Caps Lock Key (Disable) • Override Caps Lock Key (Enable). NOTE If both Simulated Caps Lock and Caps Lock Override are enabled, Caps Lock Override takes precedence.
1 - 20 MP6000 BAR CODE PROGRAMMING GUIDE USB CAPS Lock Override (continued) *Do Not Override Caps Lock Key (Disable)
USB INTERFACE BAR CODES 1 - 21 Scan Disable Mode Parameter # 1214 This parameter determines the behavior of the MP6000 when it receives a Scan Disable directive from the connected host. Options: • *Full Disable - Scanning bar codes is disabled. • Transmit Disable - The MP6000 may scan bar codes, but transmission of bar code data is disabled. • Auto Disable - MP6000 disables scanning after transmission of a bar code, and remains disabled until the host sends a Scan Enable.
1 - 22 MP6000 BAR CODE PROGRAMMING GUIDE Scan Disable Mode (continued) Transmit Disable (1)
USB INTERFACE BAR CODES 1 - 23 Scan Disable Mode (continued) Auto Disable (2)
1 - 24 MP6000 BAR CODE PROGRAMMING GUIDE USB Ignore Unknown Characters This option applies only to the IBM device. Unknown characters are characters the host does not recognize. Options: • *Send Bar Codes with Unknown Characters - Select Send Bar Codes With Unknown Characters to send all bar code data except for unknown characters. The MP6000 issues no error beeps.
USB INTERFACE BAR CODES 1 - 25 USB Ignore Unknown Characters (continued) Do Not Send Bar Codes with Unknown Characters
1 - 26 MP6000 BAR CODE PROGRAMMING GUIDE USB Convert Unknown to Code 39 This option applies only to the IBM Hand-held, IBM Table Top, and IBM OPOS (IBM Hand-held USB with Full Scan Disable) devices. Scan a bar code below to enable or disable converting unknown bar code type data to Code 39. Options: • *Disable Convert Unknown to Code 39 • Enable Convert Unknown to Code 39.
USB INTERFACE BAR CODES 1 - 27 USB Convert Unknown to Code 39 (continued) Enable Convert Unknown to Code 39
1 - 28 MP6000 BAR CODE PROGRAMMING GUIDE USB Ignore Beep Directive This applies only to IBM Hand-held, IBM Table Top, and IBM OPOS (IBM Hand-held USB with Full Scan Disable) devices. Scan one of the following bar codes to honor or ignore a beep directive. All directives are still acknowledged as if they were processed. Options: • Honor USB Beep Directive • *Ignore USB Beep Directive.
USB INTERFACE BAR CODES 1 - 29 USB Ignore Beep Directive (continued) *Ignore USB Beep Directive
1 - 30 MP6000 BAR CODE PROGRAMMING GUIDE USB Ignore Type Directive This applies only to IBM hand-held, IBM tabletop, and OPOS devices. Scan one of the following bar codes to honor or ignore a code type enable/disable directive. All directives are still acknowledged as if they were processed. Options: • Honor USB Ignore Type Directive • *Ignore USB Type Directive.
USB INTERFACE BAR CODES 1 - 31 USB Ignore Type Directive (continued) *Ignore USB Type Directive
1 - 32 MP6000 BAR CODE PROGRAMMING GUIDE Emulate Keypad Enable this to send all characters as ASCII sequences over the numeric keypad. For example ASCII A transmits as “ALT make” 0 6 5 “ALT Break”. Options: • *Disable Keypad Emulation • Enable Keypad Emulation.
USB INTERFACE BAR CODES 1 - 33 Emulate Keypad (continued) Enable Keypad Emulation
1 - 34 MP6000 BAR CODE PROGRAMMING GUIDE Emulate Keypad with Leading Zero Enable this to send character sequences sent over the numeric keypad as ISO characters which have a leading zero. For example ASCII A transmits as “ALT MAKE” 0 0 6 5 “ALT BREAK”. Options: • *Disable Keypad Emulation with Leading Zero • Enable Keypad Emulation with Leading Zero.
USB INTERFACE BAR CODES 1 - 35 Emulate Keypad with Leading Zero (continued) Enable Keypad Emulation with Leading Zero
1 - 36 MP6000 BAR CODE PROGRAMMING GUIDE USB Keyboard FN1 Substitution This option applies only to the USB HID Keyboard Emulation device. Enable this to replace any FN1 characters in an EAN 128 bar code with a user-selected Key Category and value (see FN1 Substitution Values on page 5-94 to set the Key Category and Key Value). Options: • Enable USB Keyboard FN1 Substitution • *Disable USB Keyboard FN1 Substitution.
USB INTERFACE BAR CODES 1 - 37 USB Keyboard FN 1 Substitution (continued) *Disable USB Keyboard FN1 Substitution
1 - 38 MP6000 BAR CODE PROGRAMMING GUIDE Function Key Mapping ASCII values under 32 are normally sent as a control-key sequences (see Table 1-5 on page 1-63). Enable this parameter to send the keys in bold in place of the standard key mapping. Table entries that do not have a bold entry remain the same whether or not you enable this parameter. Options: • *Disable Function Key Mapping • Enable Function Key Mapping.
USB INTERFACE BAR CODES 1 - 39 Function Key Mapping (continued) Enable Function Key Mapping
1 - 40 MP6000 BAR CODE PROGRAMMING GUIDE Convert Case Enable this to convert all bar code data to the selected case. Options: • *No Case Conversion • Convert All to Upper Case • Convert All to Lower Case.
USB INTERFACE BAR CODES 1 - 41 Convert Case (continued) Convert All to Upper Case
1 - 42 MP6000 BAR CODE PROGRAMMING GUIDE Convert Case (continued) Convert All to Lower Case
USB INTERFACE BAR CODES 1 - 43 USB Static CDC When disabled, each device connected consumes another COM port (first device = COM1, second device = COM2, third device = COM3, etc.) When enabled, each device connects to the same COM port Options: • *Enable USB Static CDC • Disable USB Static CDC.
1 - 44 MP6000 BAR CODE PROGRAMMING GUIDE USB Static CDC (continued) Disable USB Static CDC
USB INTERFACE BAR CODES 1 - 45 USB Transmission Speed Parameters Use the following parameters to speed USB data transmission: • USB HID Polling Interval - When using more current USB systems, use this parameter to set a lower interval in order to increase data transmission speed. • Fast HID Keyboard - When configured as a USB HID keyboard device, use this parameter to increase the data transmission speed of printable (7-bit) ASCII characters.
1 - 46 MP6000 BAR CODE PROGRAMMING GUIDE USB HID Polling Interval (continued) 2 msec
USB INTERFACE BAR CODES 1 - 47 USB HID Polling Interval (continued) 3 msec
1 - 48 MP6000 BAR CODE PROGRAMMING GUIDE USB HID Polling Interval (continued) 4 msec
USB INTERFACE BAR CODES 1 - 49 USB HID Polling Interval (continued) 5 msec
1 - 50 MP6000 BAR CODE PROGRAMMING GUIDE USB HID Polling Interval (continued) 6 msec
USB INTERFACE BAR CODES 1 - 51 USB HID Polling Interval (continued) 7 msec
1 - 52 MP6000 BAR CODE PROGRAMMING GUIDE USB HID Polling Interval (continued) *8 msec
USB INTERFACE BAR CODES 1 - 53 USB HID Polling Interval (continued) 9 msec
1 - 54 MP6000 BAR CODE PROGRAMMING GUIDE Fast HID Keyboard This option transmits USB HID keyboard data at a faster rate. Options: • Enable Fast HID Keyboard • * Disable Fast HID Keyboard. NOTE Enabling Emulate Keypad on page 1-32 or Quick Keypad Emulation overrides Fast HID Keyboard.
USB INTERFACE BAR CODES 1 - 55 Fast HID Keyboard (continued) *Disable
1 - 56 MP6000 BAR CODE PROGRAMMING GUIDE Quick Keypad Emulation This option applies only to the HID keyboard emulation device when Emulate Keypad on page 1-32 is enabled. This parameter enables a quicker method of emulation utilizing the numeric keypad. The default value is Disable. Options: • Enable Quick Keypad Emulation • *Disable Quick Keypad Emulation. NOTE Enabling Emulate Keypad on page 1-32 or Quick Keypad Emulation overrides Fast HID Keyboard.
USB INTERFACE BAR CODES 1 - 57 Quick Keypad Emulation (continued) *Disable
1 - 58 MP6000 BAR CODE PROGRAMMING GUIDE IBM USB Scale Default Response Status Parameter #1286 An MP6200 (MP6000 configured with a scale) sends a 2-byte scale status to the IBM USB Point of Sale (POS) system as the default setting. This parameter allows a user to program the MP6200 scanner/scale to send either 2-byte scale status, or a 3-byte scale extended status.
USB INTERFACE BAR CODES 1 - 59 • 3-byte Scale Status - Extended Scale Status Enabled: When enabled, the MP6200 scanner/scale sends an additional scale status byte to the IBM POS with the information shown in Table 1-4. Table 1-4 Scale Status Byte 2 Bit Position Description 0 Configuration successful. 1 Scale under zero. 2 Scale over capacity. 3 Scale center-of-zero. 4 Scale requires zeroing. 5 Scale warm up in progress. 6 Duplicate weight (United Kingdom mode only).
1 - 60 MP6000 BAR CODE PROGRAMMING GUIDE IBM USB Scale Default Response Status (continued) 3-byte IBM USB Scale Status - Extended Scale Status Enabled (1)
USB INTERFACE BAR CODES 1 - 61 IBM Specification Version The IBM USB interface specification version selected defines how code types are reported over the IBM USB interface. Options: • Original Specification • *Version 2.2.
1 - 62 MP6000 BAR CODE PROGRAMMING GUIDE IBM Specification Version (continued) *Version 2.
USB INTERFACE BAR CODES 1 - 63 ASCII Character Set for USB Table 1-5 USB Prefix/Suffix Values Full ASCII Code 39 Encode Char.
1 - 64 MP6000 BAR CODE PROGRAMMING GUIDE Table 1-5 USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.acter Prefix/ Suffix Value Keystroke 1026 $Z CTRL Z 1027 %A CTRL [/ESC1 1028 %B CTRL \ 1029 %C CTRL ] 1030 %D CTRL 6 1031 %E CTRL - 1032 Space Space 1033 /A ! 1034 /B “ 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G ‘ 1040 /H ( 1041 /I ) 1042 /J * 1043 /K + 1044 /L , 1045 - - 1046 . .
USB INTERFACE BAR CODES 1 - 65 Table 1-5 USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.
1 - 66 MP6000 BAR CODE PROGRAMMING GUIDE Table 1-5 USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.
USB INTERFACE BAR CODES 1 - 67 Table 1-5 USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.acter Prefix/ Suffix Value Keystroke 1113 +Q q 1114 +R r 1115 +S s 1116 +T t 1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1The keystroke in bold transmits only if you enable Function Key Mapping on page 1-38. Otherwise, the unbolded keystroke transmits.
1 - 68 MP6000 BAR CODE PROGRAMMING GUIDE Table 1-6 USB ALT Key Character Set ALT Keys Keystroke 2064 ALT 2 2065 ALT A 2066 ALT B 2067 ALT C 2068 ALT D 2069 ALT E 2070 ALT F 2071 ALT G 2072 ALT H 2073 ALT I 2074 ALT J 2075 ALT K 2076 ALT L 2077 ALT M 2078 ALT N 2079 ALT O 2080 ALT P 2081 ALT Q 2082 ALT R 2083 ALT S 2084 ALT T 2085 ALT U 2086 ALT V 2087 ALT W 2088 ALT X 2089 ALT Y 2090 ALT Z
USB INTERFACE BAR CODES 1 - 69 Table 1-7 USB GUI Key Character Set GUI Key Keystroke 3000 Right Control Key 3048 GUI 0 3049 GUI 1 3050 GUI 2 3051 GUI 3 3052 GUI 4 3053 GUI 5 3054 GUI 6 3055 GUI 7 3056 GUI 8 3057 GUI 9 3065 GUI A 3066 GUI B 3067 GUI C 3068 GUI D 3069 GUI E 3070 GUI F 3071 GUI G 3072 GUI H 3073 GUI I 3074 GUI J 3075 GUI K 3076 GUI L 3077 GUI M 3078 GUI N 3079 GUI O 3080 GUI P 3081 GUI Q Note: GUI Shift Keys - The Apple™ iMac keyboard
1 - 70 MP6000 BAR CODE PROGRAMMING GUIDE Table 1-7 USB GUI Key Character Set (Continued) GUI Key Keystroke 3082 GUI R 3083 GUI S 3084 GUI T 3085 GUI U 3086 GUI V 3087 GUI W 3088 GUI X 3089 GUI Y 3090 GUI Z Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on either side of the space bar. Windows-based systems have a GUI key to the left of the left ALT key, and to the right of the right ALT key.
USB INTERFACE BAR CODES 1 - 71 Table 1-8 USB F Key Character Set F Keys Keystroke 5001 F1 5002 F2 5003 F3 5004 F4 5005 F5 5006 F6 5007 F7 5008 F8 5009 F9 5010 F10 5011 F11 5012 F12 5013 F13 5014 F14 5015 F15 5016 F16 5017 F17 5018 F18 5019 F19 5020 F20 5021 F21 5022 F22 5023 F23 5024 F24
1 - 72 MP6000 BAR CODE PROGRAMMING GUIDE Table 1-9 USB Numeric Keypad Character Set Numeric Keypad Keystroke 6042 * 6043 + 6044 undefined 6045 - 6046 .
USB INTERFACE BAR CODES 1 - 73 Table 1-10 USB Extended Keypad Character Set Extended Keypad Keystroke 7001 Break 7002 Delete 7003 PgUp 7004 End 7005 Pg Dn 7006 Pause 7007 Scroll Lock 7008 Backspace 7009 Tab 7010 Print Screen 7011 Insert 7012 Home 7013 Enter 7014 Escape 7015 Up Arrow 7016 Down Arrow 7017 Left Arrow 7018 Right Arrow
1 - 74 MP6000 BAR CODE PROGRAMMING GUIDE
CHAPTER 2 RS-232 INTERFACE BAR CODES Introduction This chapter includes the programming bar codes for the RS-232 host interface. Use the RS-232 interface to connect the MP6000 to POS devices, host computers, or other devices with an available RS-232 port (e.g., com port). For detailed technical information about the MP6000 including installation, setting up interfaces, calibrating the scale, and operation refer to the MP6000 Integrator Guide (p/n 72E-172632-xx).
2-2 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Parameter Defaults Table 2-1 lists the defaults for RS-232 host parameters. To change any option, scan the appropriate bar code(s) provided. NOTE See Appendix A, STANDARD DEFAULT PARAMETERS for all user preferences, hosts, symbologies, and miscellaneous default parameters.
RS-232 INTERFACE BAR CODES 2-3 RS-232 Host Parameters Various RS-232 hosts use their own parameter default settings. Selecting standard, ICL, Fujitsu, Wincor-Nixdorf Mode A, Wincor-Nixdorf Mode B, OPOS/JPOS, Olivetti, Omron, Common Use Terminal Equipment (CUTE-LP/LG bar code readers), NCR, or Datalogic sets the defaults listed in Table 2-2 and Table 2-3.
2-4 MP6000 BAR CODE PROGRAMMING GUIDE Table 2-3 Terminal Specific RS-232 (Continued) Parameter Olivetti Omron CUTE NCR Datalogic Serial Response Timeout 9.9 Sec. 9.9 Sec. 9.9 Sec. 9.9 Sec. 9.9 Sec.
RS-232 INTERFACE BAR CODES RS-232 Host Parameters (continued) Selecting ICL, Fujitsu, Wincor-Nixdorf Mode A, Wincor-Nixdorf Mode B, OPOS/JPOS, Olivetti, Omron, Common Use Terminal Equipment (CUTE-LP/LG bar code readers), NCR, or Datalogic enables the transmission of code ID characters listed in Table 2-4 and Table 2-5. These code ID characters are not programmable and are separate from the Transmit Code ID feature. Do not enable the Transmit Code ID feature for these terminals.
2-6 MP6000 BAR CODE PROGRAMMING GUIDE Table 2-5 Terminal Specific Code ID Characters Code Type Olivetti Omron CUTE NCR Datalogic UPC-A A A A A A UPC-E C E None E E EAN-8/JAN-8 B FF None FF FF EAN-13/JAN-13 A F A F F Bookland EAN A F None None None Code 39 M C 3 B1 * Code 39 Full ASCII None None 3 None None Trioptic None None None None $T Code 32 None None None None AE Codabar N N None None % Code 128 K L
RS-232 INTERFACE BAR CODES 2-7 RS-232 Host Types Scan one of the bar codes that follow to select RS-232 as the host interface. Options: • *Standard RS-232 • ICL RS-232 • Wincor-Nixdorf RS-232 Mode A • Wincor-Nixdorf RS-232 Mode B • Olivetti ORS4500 • Omron • OPOS/JPOS • Fujitsu RS-232 • CUTE 2 • NCR Variant (both Scanner-Only and Scanner/Scale variants) • RS-232 Host -Datalogic Variant • Datalogic Variant. NOTES 1 Scanning Standard RS-232 activates the RS-232 driver, but does not change port settings (e.
2-8 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Host Types (continued) ICL RS-232
RS-232 INTERFACE BAR CODES RS-232 Host Types (continued) Wincor-Nixdorf RS-232 Mode A 2-9
2 - 10 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Host Types (continued) Wincor-Nixdorf RS-232 Mode B
RS-232 INTERFACE BAR CODES 2 - 11 RS-232 Host Types (continued) Olivetti ORS4500
2 - 12 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Host Types (continued) Omron
RS-232 INTERFACE BAR CODES 2 - 13 RS-232 Host Types (continued) OPOS/JPOS
2 - 14 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Host Types (continued) Fujitsu RS-232
RS-232 INTERFACE BAR CODES 2 - 15 RS-232 Host Types (continued) CUTE 2
2 - 16 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Host Types (continued) Scan the bar code below to enable the NCR variant of the RS-232 host.
RS-232 INTERFACE BAR CODES 2 - 17 RS-232 Host Types (continued) RS-232 Host -Datalogic Variant Scan the bar code below to enable the Datalogic variant of the RS-232 host.
2 - 18 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Host Preferences Baud Rate Baud rate is the number of bits of data transmitted per second. Set the MP6000 's baud rate to match the baud rate setting of the host device. Otherwise, data may not reach the host device or may reach it in distorted form. NOTE The MP6000 does not support baud rates below 9600. Options: • *Baud Rate 9600 • Baud Rate 19,200 • Baud Rate 38,400 • Baud Rate 57,600 • Baud Rate 115,200.
RS-232 INTERFACE BAR CODES 2 - 19 Baud Rate (continued) Baud Rate 19,200
2 - 20 MP6000 BAR CODE PROGRAMMING GUIDE Baud Rate (continued) Baud Rate 38,400
RS-232 INTERFACE BAR CODES 2 - 21 Baud Rate (continued) Baud Rate 57,600
2 - 22 MP6000 BAR CODE PROGRAMMING GUIDE Baud Rate (continued) Baud Rate 115,200
RS-232 INTERFACE BAR CODES 2 - 23 Parity A parity check bit is the most significant bit of each ASCII coded character. Select the parity type according to host device requirements. Options: • Odd: Select parity to set the parity bit value to 0 or 1, based on data, to ensure that the coded character contains an odd number of 1 bits. • Even: Select parity to set the parity bit value is set to 0 or 1, based on data, to ensure that the coded character contains an even number of 1 bits.
2 - 24 MP6000 BAR CODE PROGRAMMING GUIDE Parity (continued) Even
RS-232 INTERFACE BAR CODES 2 - 25 Parity (continued) *None
2 - 26 MP6000 BAR CODE PROGRAMMING GUIDE Stop Bits The stop bit(s) at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream. Select the number of stop bits (one or two) based on the number the receiving terminal is programmed to accommodate. Set the number of stop bits to match host device requirements. Options: • *1 Stop Bit • 2 Stop Bits.
RS-232 INTERFACE BAR CODES 2 - 27 Stop Bits (continued) 2 Stop Bits
2 - 28 MP6000 BAR CODE PROGRAMMING GUIDE Data Bits This parameter allows the MP6000 to interface with devices requiring a 7-bit or 8-bit ASCII protocol. Options: • 7-bit • *8-bit.
RS-232 INTERFACE BAR CODES 2 - 29 Data Bits (continued) *8-Bit
2 - 30 MP6000 BAR CODE PROGRAMMING GUIDE Check Receive Errors Select whether or not to check the parity, framing, and overrun of received characters. The parity value of received characters is verified against the parity parameter selected in the section Parity on page 2-23. Options: • *Check For Received Errors (Enable) • Do Not Check For Received Errors (Disable).
RS-232 INTERFACE BAR CODES 2 - 31 Check Receive Errors (continued) Do Not Check For Received Errors (Disable)
2 - 32 MP6000 BAR CODE PROGRAMMING GUIDE Hardware Handshaking The data interface consists of an RS-232 port designed to operate either with or without the hardware handshaking lines, Request to Send (RTS), and Clear to Send (CTS). Disable Standard RTS/CTS handshaking to transmit scan data as it becomes available. Select Standard RTS/CTS handshaking to transmit scan data according to the following sequence: • The MP6000 reads the CTS line for activity.
RS-232 INTERFACE BAR CODES 2 - 33 Hardware Handshaking (continued) Options: • None: Scan this bar code to disable hardware handshaking. • Standard RTS/CTS: Scan this bar code to select Standard RTS/CTS Hardware Handshaking. • RTS/CTS Option 1: If you select RTS/CTS Option 1, the MP6000 asserts RTS before transmitting and ignores the state of CTS. The scanner de-asserts RTS when the transmission completes. • RTS/CTS Option 2: If you select Option 2, RTS is always high or low (user-programmed logic level).
2 - 34 MP6000 BAR CODE PROGRAMMING GUIDE Hardware Handshaking (continued) Standard RTS/CTS
RS-232 INTERFACE BAR CODES 2 - 35 Hardware Handshaking (continued) RTS/CTS Option 1
2 - 36 MP6000 BAR CODE PROGRAMMING GUIDE Hardware Handshaking (continued) RTS/CTS Option 2
RS-232 INTERFACE BAR CODES 2 - 37 Hardware Handshaking (continued) RTS/CTS Option 3
2 - 38 MP6000 BAR CODE PROGRAMMING GUIDE Software Handshaking This parameter offers control of the data transmission process in addition to, or instead of, that offered by hardware handshaking. There are five options. If software handshaking and hardware handshaking are both enabled, hardware handshaking takes precedence. Options: • None: Select this to transmit data immediately. The MP6000 expects no response from the host.
RS-232 INTERFACE BAR CODES 2 - 39 Software Handshaking (continued) *None
2 - 40 MP6000 BAR CODE PROGRAMMING GUIDE Software Handshaking (continued) ACK/NAK
RS-232 INTERFACE BAR CODES 2 - 41 Software Handshaking (continued) ENQ
2 - 42 MP6000 BAR CODE PROGRAMMING GUIDE Software Handshaking (continued) ACK/NAK with ENQ
RS-232 INTERFACE BAR CODES 2 - 43 Software Handshaking (continued) XON/XOFF
2 - 44 MP6000 BAR CODE PROGRAMMING GUIDE Host Serial Response Timeout This parameter specifies how long the MP6000 waits for an ACK, NAK, or CTS before determining that a transmission error occurred. This only applies when in one of the ACK/NAK software handshaking modes, or RTS/CTS hardware handshaking mode. Options: • *Minimum: 2 Sec • Low: 2.5 Sec • Medium: 5 Sec • High: 7.5 Sec • Maximum: 9.9 Sec.
RS-232 INTERFACE BAR CODES 2 - 45 Host Serial Response Timeout (continued) Low: 2.
2 - 46 MP6000 BAR CODE PROGRAMMING GUIDE Host Serial Response Timeout (continued) Medium: 5 Sec
RS-232 INTERFACE BAR CODES 2 - 47 Host Serial Response Timeout (continued) High: 7.
2 - 48 MP6000 BAR CODE PROGRAMMING GUIDE Host Serial Response Timeout (continued) Maximum: 9.
RS-232 INTERFACE BAR CODES 2 - 49 RTS Line State This parameter sets the idle state of the Serial Host RTS line. Scan a bar code below to select Low RTS or High RTS line state. Options: • *Host: Low RTS • Host: High RTS.
2 - 50 MP6000 BAR CODE PROGRAMMING GUIDE RTS Line State (continued) Host: High RTS
RS-232 INTERFACE BAR CODES 2 - 51 Beep on If you enable this parameter, the MP6000 issues a beep when it detects a character on the RS-232 serial line. indicates an illegal entry or other important event. Options: • *Do Not Beep On Character (Disable) • Beep On Character (Disable).
2 - 52 MP6000 BAR CODE PROGRAMMING GUIDE Beep on (continued) *Do Not Beep On Character (Disable)
RS-232 INTERFACE BAR CODES 2 - 53 Intercharacter Delay This parameter specifies the intercharacter delay inserted between character transmissions. Options: • *Minimum: 0 msec • Low: 25 msec • Medium: 50 msec • High: 75 msec • Maximum: 99 msec.
2 - 54 MP6000 BAR CODE PROGRAMMING GUIDE Intercharacter Delay (continued) Low: 25 msec
RS-232 INTERFACE BAR CODES 2 - 55 Intercharacter Delay (continued) Medium: 50 msec
2 - 56 MP6000 BAR CODE PROGRAMMING GUIDE Intercharacter Delay (continued) High: 75 msec
RS-232 INTERFACE BAR CODES 2 - 57 Intercharacter Delay (continued) Maximum: 99 msec
2 - 58 MP6000 BAR CODE PROGRAMMING GUIDE Wincor-Nixdorf Beep/LED Options If you selected Wincor-Nixdorf Mode B, this indicates when the digital scanner beeps and turns on its LED after a decode. Options: • *Normal Operation (Beep/LED immediately after decode) • Beep/LED After Transmission • Beep/LED After CTS Pulse.
RS-232 INTERFACE BAR CODES 2 - 59 Wincor-Nixdorf Beep/LED Options (continued) Beep/LED After Transmission
2 - 60 MP6000 BAR CODE PROGRAMMING GUIDE Wincor-Nixdorf Beep/LED Options (continued) Beep/LED After CTS Pulse
RS-232 INTERFACE BAR CODES 2 - 61 Ignore Unknown Characters Unknown characters are characters the host does not recognize. Options: • *Send Bar Codes with Unknown Characters: Select to send all bar code data except for unknown characters. The MP6000 issues no error beeps. • Do Not Send Bar Codes With Unknown Characters: Select to send bar code data up to the first unknown character. The MP6000 issues an error beep.
2 - 62 MP6000 BAR CODE PROGRAMMING GUIDE Ignore Unknown Characters (continued) Do Not Send Bar Codes (with unknown characters)
RS-232 INTERFACE BAR CODES 2 - 63 NCR Variant Preferences NCR Use Prefix Parameter #1238 When NCR Variant is selected, this parameter determines whether or not the prefix is used for all communications. Options: • Disabled • *Enabled.
2 - 64 MP6000 BAR CODE PROGRAMMING GUIDE NCR Use Prefix (continued) *Enabled (01h)
RS-232 INTERFACE BAR CODES 2 - 65 NCR Prefix Parameter # 1282 When NCR variant is selected, and NCR Use Prefix is enabled, this parameter determines the Prefix Character used for all communications. The default is 1002 (STX). To select the poll interval, scan the bar code below, then scan four numeric bar codes from Appendix D, NUMERIC BAR CODES that correspond to the desired character in Table 2-6 (ASCII Character Set for RS-232 on page 2-72).
2 - 66 MP6000 BAR CODE PROGRAMMING GUIDE NCR Suffix Parameter # 1283 When NCR variant is selected, this parameter determines the suffix (terminator) character used for all communications. The default is 1003 (ETX). To select the poll interval, scan the bar code below, then scan four numeric bar codes from Appendix D, NUMERIC BAR CODES that correspond to the desired character in Table 2-6 (ASCII Character Set for RS-232 on page 2-72). Options: • Disabled • *Enabled.
RS-232 INTERFACE BAR CODES 2 - 67 NCR Use Block Check Character (BCC) Parameter #1239 When NCR variant is selected, this parameter determines whether or not to enable the use of the Block Check Character (after the Terminator byte) for all communications. Options: • Disabled • *Enabled.
2 - 68 MP6000 BAR CODE PROGRAMMING GUIDE NCR Use Block Check Character (BCC) *Enabled (01h)
RS-232 INTERFACE BAR CODES 2 - 69 NCR Interface Parameter #1240 When NCR variant is selected, this parameter determines the NCR specific interface to be used for all communications. NCR supports two interfaces: scanner only, and scanner/scale. Options: • *Follow System: Scan this bar code for auto system detection. If the system has a scale installed, the scanner/scale interface is used; if the system has no scale installed, scanner only is used.
2 - 70 MP6000 BAR CODE PROGRAMMING GUIDE NCR Interface (continued) Scanner Only (01h)
RS-232 INTERFACE BAR CODES 2 - 71 NCR Interface (continued) Scanner/Scale (01h)
2 - 72 MP6000 BAR CODE PROGRAMMING GUIDE ASCII Character Set for RS-232 You can assign the values in Table 2-6 as prefixes or suffixes for ASCII character data transmission.
RS-232 INTERFACE BAR CODES 2 - 73 Table 2-6 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1028 %B FS 1029 %C GS 1030 %D RS 1031 %E US 1032 Space Space 1033 /A ! 1034 /B " 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G ‘ 1040 /H ( 1041 /I ) 1042 /J * 1043 /K + 1044 /L , 1045 - - 1046 . .
2 - 74 MP6000 BAR CODE PROGRAMMING GUIDE Table 2-6 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1059 %F ; 1060 %G < 1061 %H = 1062 %I > 1063 %J ? 1064 %V @ 1065 A A 1066 B B 1067 C C 1068 D D 1069 E E 1070 F F 1071 G G 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M 1078 N N 1079 O O 1080 P P 1081 Q Q 1082 R R 1083 S S 1084 T T 1085 U U 1086 V V 1087 W
RS-232 INTERFACE BAR CODES 2 - 75 Table 2-6 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1090 Z Z 1091 %K [ 1092 %L \ 1093 %M ] 1094 %N ^ 1095 %O _ 1096 %W ` 1097 +A a 1098 +B b 1099 +C c 1100 +D d 1101 +E e 1102 +F f 1103 +G g 1104 +H h 1105 +I i 1106 +J j 1107 +K k 1108 +L l 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S s 1116 +T t 1117 +U
2 - 76 MP6000 BAR CODE PROGRAMMING GUIDE Table 2-6 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1127 Undefined 7013 ENTER
CHAPTER 3 IBM RS-485 INTERFACE BAR CODES Introduction This chapter includes the programming bar codes for the IBM RS-485 host interface. For detailed technical information about the MP6000 including installation, setting up interfaces, calibrating the scale, and operation refer to the MP6000 Integrator Guide (p/n 72E-172632-xx). Throughout the programming bar code menus, asterisks (*) indicate default values.
3-2 MP6000 BAR CODE PROGRAMMING GUIDE IBM Parameter Defaults Table 3-1 lists the defaults for IBM host parameters. To change any option, scan the appropriate bar code(s) provided in the Parameter Descriptions section beginning on page 3-3. NOTE See Appendix A, STANDARD DEFAULT PARAMETERS for all user preferences, hosts, symbologies, and miscellaneous default parameters.
IBM RS-485 INTERFACE BAR CODES IBM RS-485 Host Parameters Port Address This parameter sets the IBM RS-485 port used. NOTE Scanning one of these bar codes enables the RS-485 interface on the MP6000. Options: • *None Selected • Hand-held Scanner Emulation (Port 9B) • Non-IBM Scanner Emulation (Port 5B) • Table-top Scanner Emulation (Port 17).
3-4 MP6000 BAR CODE PROGRAMMING GUIDE Port Address (continued) Hand-held Scanner Emulation (Port 9B)
IBM RS-485 INTERFACE BAR CODES Port Address (continued) Non-IBM Scanner Emulation (Port 5B) 3-5
3-6 MP6000 BAR CODE PROGRAMMING GUIDE Port Address (continued) Table-top Scanner Emulation (Port 17)
IBM RS-485 INTERFACE BAR CODES Scale Port Address The scale port address must be configured for the scale to operate on the IBM RS-485 bus. Options: • *None Selected • Port 6A • Port 6B • Port 6E.
3-8 MP6000 BAR CODE PROGRAMMING GUIDE Scale Port Address (continued) Port 6A
IBM RS-485 INTERFACE BAR CODES Scale Port Address (continued) Port 6B 3-9
3 - 10 MP6000 BAR CODE PROGRAMMING GUIDE Scale Port Address (continued) Port 6E
IBM RS-485 INTERFACE BAR CODES 3 - 11 IBM RS-485 Miscellaneous Parameters Convert Unknown to Code 39 Scan a bar code below to enable or disable the conversion of unknown bar code type data to Code 39. Options: • Enable Convert Unknown to Code 39 • *Disable Convert Unknown to Code 39.
3 - 12 MP6000 BAR CODE PROGRAMMING GUIDE Convert Unknown to Code 39 (continued) *Disable Convert Unknown to Code 39
IBM RS-485 INTERFACE BAR CODES 3 - 13 Ignore Beep Directive Scan one of the following bar codes to honor or ignore a beep directive made over the IBM RS-485 bus. All directives are still acknowledged to the IBM RS-485 host as if they were processed. Options: • Honor Beep Directive • *Ignore Beep Directive.
3 - 14 MP6000 BAR CODE PROGRAMMING GUIDE Ignore Beep Directive (continued) *Ignore Beep Directive
IBM RS-485 INTERFACE BAR CODES 3 - 15 Ignore Configuration Directive Scan one of the following bar codes to honor or ignore a code type enable/disable directive made over the IBM RS-485 bus. All directives are still acknowledged to the IBM RS-485 host as if they were processed. Options: • Honor Configuration Directive • *Ignore Configuration Directive.
3 - 16 MP6000 BAR CODE PROGRAMMING GUIDE Ignore Configuration Directive (continued) *Ignore Configuration Directive
IBM RS-485 INTERFACE BAR CODES 3 - 17 Scan Disable Mode Parameter # 1214 This parameter determines the behavior of the MP6000 when it receives a Scan Disable directive from the connected host. Options: • *Full Disable: Scanning bar codes is disabled. • Transmit Disable: The MP6000 may scan bar codes, but transmission of bar code data is disabled. • Auto Disable: MP6000 disables scanning after transmission of a bar code, and remains disabled until the host sends a Scan Enable.
3 - 18 MP6000 BAR CODE PROGRAMMING GUIDE Scan Disable Mode Transmit Disable (1)
IBM RS-485 INTERFACE BAR CODES 3 - 19 Scan Disable Mode Auto Disable (2)
3 - 20 MP6000 BAR CODE PROGRAMMING GUIDE
CHAPTER 4 SCALE CONFIGURATION Introduction You can program the MP6000 to perform various functions, or activate different features. This chapter describes each scale calibration feature, and provides programming bar codes for selecting these features. The MP6000 ships with the settings shown in Table 4-1 on page 4-2 (also see Appendix A, STANDARD DEFAULT PARAMETERS for all host device and miscellaneous defaults). If the default values suit requirements, programming is not necessary.
4-2 MP6000 BAR CODE PROGRAMMING GUIDE Scanning Sequence Examples In most cases, scanning one bar code sets the parameter value. For example, to enable the Scale Display, scan the Enable Scale Display Configuration bar code listed under Scale Display Configuration on page 4-12. Errors While Scanning Unless otherwise specified, to correct an error during a scanning sequence, just re-scan the correct parameter. Scale Parameter Defaults Table 4-1 lists defaults for user preferences parameters.
SCALE CONFIGURATION 4-3 Legal Scale Units Parameter # 995 Scan a weight unit below to set the legal weight units for the MP6000. Scan Kilograms for international units; scan Pounds for the United States. NOTE This legal scale unit can only be programmed when the scale is placed into a legal scale calibration mode. Refer to the MP6000 Integrator Guide (p/n 72E-172632-xx) for detailed information about scale calibration. Options: • Kilograms • Pounds.
4-4 MP6000 BAR CODE PROGRAMMING GUIDE Legal Scale Units (continued) Pounds (1)
SCALE CONFIGURATION 4-5 Legal Scale Dampening Filter Setting Parameter # 996 Scan a bar code below to set the vibration sensitivity of the scale. The higher the number value, the less sensitive the scale is to vibration. The scale must be in a calibration mode to program this parameter. Refer to the MP6000 Integrator Guide (p/n 72E-172632-xx) for detailed information about calibrating the scale.
4-6 MP6000 BAR CODE PROGRAMMING GUIDE Legal Scale Dampening Filter Setting (continued) * Low Vibration Sensitivity (1)
SCALE CONFIGURATION Legal Scale Dampening Filter Setting (continued) Very Low Vibration Sensitivity (2) 4-7
4-8 MP6000 BAR CODE PROGRAMMING GUIDE Legal Scale Dampening Filter Setting (continued) Ultra Low Vibration Sensitivity (3)
SCALE CONFIGURATION 4-9 Scale Enable Parameter # 1197 This parameter enables and disables the functionality of an already existing scale. If the scale was not properly installed, this parameter does nothing. Options: • *Scale Enable • Scale Disable.
4 - 10 MP6000 BAR CODE PROGRAMMING GUIDE Scale Enable (continued) Scale Disable
SCALE CONFIGURATION 4 - 11 Scale Reset Parameter # 6009 Scan STISCLRST to reset the scale. This parameter can be scanned in any mode of operation. If a pole display is enabled, and installed, it repeats the 7-segment test. Refer to the MP6000 Integrator Guide (p/n 72E-172632-xx) for details.
4 - 12 MP6000 BAR CODE PROGRAMMING GUIDE Scale Display Configuration Parameter # 986 Scan Enable Scale Display Configuration below to enable the pole display port. Scale Display Configuration is disabled by default. Options: • Enable Scale Display Configuration: When a pole display is installed and connected to the MP6000/scale, the pole display shows weight, and/or additional alphanumeric information associated with the state of the scale.
SCALE CONFIGURATION 4 - 13 Scale Display Configuration (continued) * Disable Scale Display Configuration (0)
4 - 14 MP6000 BAR CODE PROGRAMMING GUIDE Scale Enforce Zero Return Parameter # 987 Scan a bar code to below to enable or disable enforce zero return. Options: • *Disable Scale Enforce Zero Return: Provides live gross weight in real time upon request from a Point-of-sale (POS) system. This is the factory default. • Enable Scale Enforce Zero Return: The scale must return to zero weight between POS weight requests.
SCALE CONFIGURATION 4 - 15 Scale Enforce Zero Return (continued) * Disable Scale Enforce Zero Return (0)
4 - 16 MP6000 BAR CODE PROGRAMMING GUIDE Scale Beep After Weight Request Parameter # 988 Scan Enable Scale Beep After Weight below to sound a beep tone after a successful weight request. Options: • Enable Scale Beep After Weight: The scale beeps a single beep tone after each successful weight request by the POS system. The beep tone sounds when the weight is above zero, stable, and the previous weight does not equal the present weight.
SCALE CONFIGURATION 4 - 17 Scale Beep After Weight Request (continued) * Disable Scale Beep After Weight (0)
4 - 18 MP6000 BAR CODE PROGRAMMING GUIDE Ignore Scale Pole Directives Parameter #1242 The pole display is required to be consumer facing if the POS system is not certified for displaying live gross weight.
SCALE CONFIGURATION 4 - 19 Ignore Scale Pole Directives (continued) Honor Scale Pole Directives (0)
4 - 20 MP6000 BAR CODE PROGRAMMING GUIDE Maximum Initial Zero Setting Range Parameter #1285 Initial Zero Setting - The scale indication is set to zero automatically when the device is powered on, and before it is ready for use. The default Initial Zero Setting range is set to -5% to +15% of the maximum capacity of the scale (i.e.: -1.5 lb to 4.5 lb, -0.75 kg to 2.25 kg). When an object is left on the scale, and within this weight range at scale power up, it automatically zeroes the weight.
SCALE CONFIGURATION 4 - 21 Maximum Initial Zero Setting Range (continued) Table 4-2 Parameter Value Settings. Param Value Lbs Kgs 2 (minimum) 0.6 0.30 3 0.9 0.45 4 1.2 0.60 5 1.5 0.75 6 1.8 0.90 7 2.1 1.05 8 2.4 1.20 9 2.7 1.35 10 3.0 1.50 11 3.3 1.65 12 3.6 1.80 13 3.9 1.95 14 4.2 2.10 15 (maximum/default) 4.5 2.
4 - 22 MP6000 BAR CODE PROGRAMMING GUIDE
CHAPTER 5 USER PREFERENCES & MISCELLANEOUS OPTIONS Introduction You can program the MP6000 to perform various functions, or activate different features. This chapter describes each user preference feature and provides programming bar codes for selecting these features. The MP6000 ships with the settings shown in Table 5-1 on page 5-2 (also see Appendix A, STANDARD DEFAULT PARAMETERS for all host device and miscellaneous defaults). If the default values suit requirements, programming is not necessary.
5-2 MP6000 BAR CODE PROGRAMMING GUIDE Scanning Sequence Examples In most cases, scanning one bar code sets the parameter value. For example, to set the beeper tone to high, scan the High Tone (beeper tone) bar code in the Beeper Tone section on page 5-11. Other parameters, such as Serial Response Timeout or Data Transmission Formats, require scanning several bar codes. See these parameter descriptions for this procedure.
USER PREFERENCES & MISCELLANEOUS OPTIONS Table 5-1 User Preferences Parameter Defaults (Continued) Parameter Parameter Number Default Page Number Mobile Phone Display Mode 716 Disable 5-38 PDF Prioritization 719 Disable 5-40 PDF Prioritization Timeout 720 300 ms 5-42 Center Object Detect 1128 Enable 5-43 Center IR Sensitivity 1219 Medium 5-45 Stitching Type 1229 Swipe Stitching 5-48 Scanning Usage Mode 1230 Cashier/Trained User 5-50 RS-232 Device Port Configuration 1246 A
5-4 MP6000 BAR CODE PROGRAMMING GUIDE User Preferences Set Default Parameter You can reset the MP6000 to two types of defaults: factory defaults or custom defaults. Scan the appropriate bar code below to reset the MP6000 to its default settings and/or set its current settings as custom defaults. Options: • *Set Defaults: Scan this bar code to reset all default parameters as follows.
USER PREFERENCES & MISCELLANEOUS OPTIONS Set Default Parameter (continued) Set Factory Defaults 5-5
5-6 MP6000 BAR CODE PROGRAMMING GUIDE Set Default Parameter (continued) Write to Custom Defaults
USER PREFERENCES & MISCELLANEOUS OPTIONS 5-7 Parameter Bar Code Scanning Parameter # 236 To disable the decoding of parameter bar codes, including the Set Defaults parameter bar codes, scan the Disable Parameter Scanning bar code below. To enable decoding of parameter bar codes, scan Enable Parameter Scanning. Options: • *Enable Parameter Bar Code Scanning • Disable Parameter Bar Code Scanning.
5-8 MP6000 BAR CODE PROGRAMMING GUIDE Parameter Bar Code Scanning (continued) Disable Parameter Bar Code Scanning (00h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5-9 Beep After Good Decode Parameter # 56 Scan a bar code below to select whether or not the MP6000 beeps after a good decode. If selecting Do Not Beep After Good Decode, the beeper still operates during parameter menu scanning and to indicate error conditions. Options: • *Beep After Good Decode (Enable) • Do Not Beep After Good Decode (Disable).
5 - 10 MP6000 BAR CODE PROGRAMMING GUIDE Beep After Good Decode (continued) Do Not Beep After Good Decode (Disable) (00h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 11 Beeper Tone Parameter # 145 To select a decode beep frequency (tone), scan one of the bar codes that follow. If the decode tone is set to Off, the Volume/Tone button on the MP6000 cannot be used to control the volume of decode tones. To enable the Volume/Tone button, scan a tone other than Off. Options: • Off • Low Tone • *Medium Tone • High Tone • Medium to High Tone (2-tone) • Chirp.
5 - 12 MP6000 BAR CODE PROGRAMMING GUIDE Beeper Tone (continued) Low Tone (02
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 13 Beeper Tone (continued) *Medium Tone (01h)
5 - 14 MP6000 BAR CODE PROGRAMMING GUIDE Beeper Tone (continued) High Tone (00h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 15 Beeper Tone (continued) Medium to High Tone (2-tone) (04h)
5 - 16 MP6000 BAR CODE PROGRAMMING GUIDE Beeper Tone (continued) Chirp (05h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 17 Beeper Volume Parameter # 140 To select a beeper volume, scan the one of the bar codes that follows. Options: • Low Volume • Medium Volume • High Volume • Higher Volume • *Highest Volume.
5 - 18 MP6000 BAR CODE PROGRAMMING GUIDE Beeper Volume (continued) Medium Volume (01h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 19 Beeper Volume (continued) High Volume (00h)
5 - 20 MP6000 BAR CODE PROGRAMMING GUIDE Beeper Volume (continued) Higher Volume (03h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 21 Beeper Volume (continued) *Highest Volume (04h)
5 - 22 MP6000 BAR CODE PROGRAMMING GUIDE Beeper Duration Parameter # 628 To select the duration for the beeper, scan one of the following bar codes. Options: • Short • * Medium • Long.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 23 Beeper Duration (continued) * Medium (01h)
5 - 24 MP6000 BAR CODE PROGRAMMING GUIDE Beeper Duration (continued) Long (02h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 25 Volume Button Enable Parameter # 1287 When this parameter is enabled the physical Volume button on the front panel of the MP6000 can be used to change the speaker volume and tone. When this parameter is disabled the speaker volume and tone cannot be changed using the physical Volume button on the front panel of the MP6000. Options: • *Enable • Disable.
5 - 26 MP6000 BAR CODE PROGRAMMING GUIDE Volume Button Enable (continued) Disable (0)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 27 Suppress Power-up Beeps Parameter # 721 Select whether or not to suppress the MP6000 power-up beeps. Options: • * Do Not Suppress Power-up Beeps • Suppress Power-up Beeps.
5 - 28 MP6000 BAR CODE PROGRAMMING GUIDE Suppress Power-up Beeps (continued) Suppress Power-up Beeps (01h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 29 Decode Session Timeout Parameter # 136 This parameter sets the maximum time decode processing continues during a scan attempt. It is programmable in 0.1 second increments from 0.5 to 9.9 seconds. The default timeout is 9.9 seconds. Options: To set a Decode Session Timeout, scan the bar code below. Next, scan two numeric bar codes from Appendix D, NUMERIC BAR CODES that correspond to the desired on time. Enter a leading zero for single digit numbers.
5 - 30 MP6000 BAR CODE PROGRAMMING GUIDE Timeout Between Decodes, Same Symbol Parameter # 137 Use this option to prevent the beeper from continuously beeping when a symbol is left in the MP6000’s field of view. It is programmable in 0.1 second increments from 0.0 to 9.9 seconds. The default interval is 0.5 seconds.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 31 Same Symbol Report Timeout Parameter # 1284 Affects how the Timeout Between Decodes, Same Symbol parameter is applied (see page 5-30). When this parameter is disabled a bar code in the decode region decodes only once, even if the bar code remains indefinitely in the region. The user must remove the bar code, and reintroduce the bar code into the region before it decodes a second time.
5 - 32 MP6000 BAR CODE PROGRAMMING GUIDE Same Symbol Report Timeout (continued) Enable (1)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 33 Swipe Frame Timeout Parameter # 1226 Specifies how much time to spend on processing the frame that is optimized to decode images where the bar code is swiped in front of the scanner. The range is 11 - 500 milliseconds. The default is 15 milliseconds. Scan the bar code below, then scan three digits from Appendix D, NUMERIC BAR CODES. If a two digit timeout is desired, scan the zero bar code before scanning the two digits.
5 - 34 MP6000 BAR CODE PROGRAMMING GUIDE Presentation Frame Timeout Parameter # 1227 Specifies how much time to spend on processing the frame that is optimized to decode images where the bar code is presented to the scanner. The range is 11 - 500 milliseconds. The default is 35 milliseconds. Scan the bar code below, then scan three digits from Appendix D, NUMERIC BAR CODES. If a two digit timeout is desired, scan the zero bar code before scanning the two digits.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 35 Cell Phone Frame Timeout Parameter # 1228 Specifies how much time to spend on processing the frame that is optimized to decode bar codes from cell phone displays. The range is 11 - 500 milliseconds. The default is 35 milliseconds. Scan the bar code below, then scan three digits from Appendix D, NUMERIC BAR CODES. If a two digit timeout is desired, scan the zero bar code before scanning the two digits.
5 - 36 MP6000 BAR CODE PROGRAMMING GUIDE Fuzzy 1D Processing Parameter # 514 This option is enabled by default to optimize decode performance on 1D bar codes, including damaged and poor quality symbols. Disable this only if you experience time delays when decoding 2D bar codes, or in detecting a no decode. Options: • *Enable Fuzzy 1D Processing • Disable Fuzzy 1D Processing.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 37 Fuzzy 1D Processing (continued) Disable Fuzzy 1D Processing (00h)
5 - 38 MP6000 BAR CODE PROGRAMMING GUIDE Mobile Phone Display Mode Parameter # 716 This mode improves bar code reading performance on mobile phones and electronic displays. Options: • *Disable Mobile Phone Display Mode • Enable Mobile Phone Display Mode.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 39 Mobile Phone Display Mode (continued) Enable Mobile Phone Display Mode (03h)
5 - 40 MP6000 BAR CODE PROGRAMMING GUIDE PDF Prioritization Parameter # 719 Enable this feature to delay decoding a 1D bar code (Code 128 of 8 to 25 characters length) by the value specified in PDF Prioritization Timeout. During that time the MP6000 attempts to decode a PDF417 symbol (e.g., on a US driver's license), and if successful reports this only. If it does not decode (can not find) a PDF417 symbol, it reports the 1D symbol after the timeout.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 41 PDF Prioritization (continued) Enable PDF Prioritization (01h)
5 - 42 MP6000 BAR CODE PROGRAMMING GUIDE PDF Prioritization Timeout Parameter # 720 When PDF Prioritization is enabled, this timeout specifies how long the MP6000 attempts to decode a PDF417 symbol before reporting the 1D bar code in the field of view. Scan the following bar code, then scan four digits from Appendix D, NUMERIC BAR CODES that specify the timeout in milliseconds. For example, to enter 400 ms, scan the following bar code, then scan 0400. The range is 0 to 5000 ms, and the default is 300 ms.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 43 Center Object Detect Parameter # 1128 This parameter controls the scanner’s ability to detect object motion in front of the scanning volume. Options: • Disable Center Object Detect • *Enable Center Object Detect.
5 - 44 MP6000 BAR CODE PROGRAMMING GUIDE Center Object Detect (continued) *Enable Center Object Detect (01h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 45 Center IR Sensitivity Parameter # 1219 This parameter controls the distance, or range, at which the scanner detects object motion in front of the scanning volume. Options: • Short • *Medium • Long.
5 - 46 MP6000 BAR CODE PROGRAMMING GUIDE Center IR Sensitivity (continued) *Medium (81)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 47 Center IR Sensitivity (continued) Long (17)
5 - 48 MP6000 BAR CODE PROGRAMMING GUIDE Stitching Type Parameter # 1229 This parameter configures the stitching algorithm to perform either where the bar code was swiped in front of the scanner, or only presented to the scanner. When the stitching algorithm is configured to run when a bar code is swiped in front of a scanner, a swipe performance of UPC family and PDF bar codes might be slightly lower.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 49 Stitching Type (continued) Presentation Stitching (01h)
5 - 50 MP6000 BAR CODE PROGRAMMING GUIDE Scanning Usage Mode Parameter # 1230 This parameter configures the scanner for either a trained user/cashier, or for self-checkout operation. Options: • *Cashier/Trained User • Self-Checkout.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 51 Scanning Usage Mode (continued) Self-Checkout (01h)
5 - 52 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Device Port Configuration Parameter # 1246 This option allows the user to select which devices to attach to the MP6000, and to which port they are attached. Scan the appropriate bar codes that follow to select the proper configuration. The available configurations/options are: • *0= Aux 1 Sensormatic, and Aux 2 RS-232 Scanner • 1 = Aux 1 Dual Cable Scale, and Aux 2 RS-232 Scanner • 2 = Aux 1 Sensormatic, and Aux 2 Dual Cable Scale.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 53 RS-232 Device Port Configuration (continued) *Aux 1 Sensormatic and Aux 2 RS-232 Scanner (00h)
5 - 54 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Device Port Configuration (continued) Aux 1 Dual Cable Scale and Aux 2 RS-232 Scanner (01h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 55 RS-232 Device Port Configuration (continued) Aux 1 Sensormatic and Aux 2 Dual Cable Scale (02h)
5 - 56 MP6000 BAR CODE PROGRAMMING GUIDE RS-232 Device Port Configuration (continued) Aux 1 Third Party Scale, Aux 2 Sensormatic (04h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 57 Third Party Scale Parameters Third Party Scale Parameter # 1294 Enable or disable Third Party Scale functionality. When disabled Third Party Scale LED Pin (parameter # 1295) and Third Party Scale Zero Pin (parameter # 1296) are ignored/overridden. Options: • Enable Third Party Scale • *Disable Third Party Scale.
5 - 58 MP6000 BAR CODE PROGRAMMING GUIDE Third Party Scale (continued) * Disable Third Party Scale (0)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 59 Third Party Scale LED Pin Parameter # 1295 This parameter defines the polarity of the LED/Tare input pin that illuminates the scale LED. This parameter has no effect if Third Party Scale (parameter # 1294) is disabled. Options: • Active Low • *Active High.
5 - 60 MP6000 BAR CODE PROGRAMMING GUIDE Third Party Scale LED Pin (continued) *Active High (1)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 61 Third Party Scale Zero Pin Parameter # 1296 This parameter defines the polarity of the zero output pin when the Scale Zero button is pressed. This parameter has no effect if Third Party Scale (parameter # 1294) is disabled. Options: • Active Low • *Active High.
5 - 62 MP6000 BAR CODE PROGRAMMING GUIDE Third Party Scale Zero Pin (continued) *Active High (1)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 63 Exclude Decode Field Of Views Parameter # 1249 Used to prevent decoding from specific fields of view. Options: • * Include All Fields Of View • Exclude Left Horizontal • Exclude Right Horizontal • Exclude Left Horizontal & Horizontal Right.
5 - 64 MP6000 BAR CODE PROGRAMMING GUIDE Exclude Decode Field Of Views (continued) Exclude Left Horizontal (1)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 65 Exclude Decode Field Of Views (continued) Exclude Right Horizontal (2)
5 - 66 MP6000 BAR CODE PROGRAMMING GUIDE Exclude Decode Field Of Views (continued) Exclude Left Horizontal & Horizontal Right (3)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 67 Illumination Configurations Parameter # 1250 Allows the illumination brightness of each field of view to be controlled. Options: • * Full Brightness on both Vertical and Horizontal • Dim Vertical Brightness Only • Extra Dim Vertical Brightness Only • Dim Horizontal Brightness Only • Extra Dim Horizontal Brightness Only • Dim Both Horizontal and Vertical • Extra Dime Both Horizontal and Vertical.
5 - 68 MP6000 BAR CODE PROGRAMMING GUIDE Illumination Configurations (continued) Dim Vertical Brightness Only (1)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 69 Illumination Configurations (continued) Extra Dim Vertical Brightness Only (2)
5 - 70 MP6000 BAR CODE PROGRAMMING GUIDE Illumination Configurations (continued) Dim Horizontal Brightness Only (3)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 71 Illumination Configurations (continued) Extra Dim Horizontal Brightness Only (4)
5 - 72 MP6000 BAR CODE PROGRAMMING GUIDE Illumination Configurations (continued) Dim Both Horizontal and Vertical (5)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 73 Illumination Configurations (continued) Extra Dime Both Horizontal and Vertical (6)
5 - 74 MP6000 BAR CODE PROGRAMMING GUIDE Product ID (PID) Type Parameter # 1281 Defines the PID value reported in USB enumeration. Options: • *Host Type Unique • Product Unique • IBM Unique.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 75 PID Type (continued) Product Unique (1)
5 - 76 MP6000 BAR CODE PROGRAMMING GUIDE PID Type (continued) IBM Unique (2)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 77 Continuous Bar Code Read Parameter # 649 Enable this to report every bar code when scanning. Options: • *Disable Continuous Bar Code Read • Enable Continuous Bar Code Read.
5 - 78 MP6000 BAR CODE PROGRAMMING GUIDE Continuous Bar Code Read (continued) Enable Continuous Bar Code Read (1h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 79 Miscellaneous Scanner Parameters Transmit Code ID Character Parameter # 45 A Code ID character identifies the code type of a scanned bar code. This is useful when decoding more than one code type. In addition to any single character prefix already selected, the Code ID character is inserted between the prefix and the decoded symbol. Select no Code ID character, a Symbol Code ID character, or an AIM Code ID character.
5 - 80 MP6000 BAR CODE PROGRAMMING GUIDE Transmit Code ID Character (continued) AIM Code ID Character (01h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 81 Transmit Code ID Character (continued) *None (00h)
5 - 82 MP6000 BAR CODE PROGRAMMING GUIDE Prefix/Suffix Values Key Category Parameter # P = 99, S1 = 98, S2 = 100 Decimal Value Parameter # P = 105, S1 = 104, S2 = 106 You can append a prefix and/or one or two suffixes to scan data for use in data editing. To set a value for a prefix or suffix, scan a four-digit number (i.e., four bar codes from Appendix D, NUMERIC BAR CODES) that corresponds to that value. See Table E-1 on page E-1 for the four-digit codes.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 83 Prefix/Suffix Values (continued) Scan Suffix 1 (06h)
5 - 84 MP6000 BAR CODE PROGRAMMING GUIDE Prefix/Suffix Values (continued) Scan Suffix 2 (08h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 85 Prefix/Suffix Values (continued) Data Format Cancel
5 - 86 MP6000 BAR CODE PROGRAMMING GUIDE Scan Data Transmission Format Parameter # 235 To set the scan data format, scan one of the following bar codes. NOTE If using this parameter do not use ADF rules to set the prefix/suffix. To set values for the prefix and/or suffix, see Prefix/Suffix Values on page 5-82.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 87 Scan Data Transmission Format (continued) (01h)
5 - 88 MP6000 BAR CODE PROGRAMMING GUIDE Scan Data Transmission Format (continued) (02h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 89 Scan Data Transmission Format (continued) (03h)
5 - 90 MP6000 BAR CODE PROGRAMMING GUIDE Scan Data Transmission Format (continued) (04h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 91 Scan Data Transmission Format (continued) (05h)
5 - 92 MP6000 BAR CODE PROGRAMMING GUIDE Scan Data Transmission Format (continued) (06h)
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 93 Scan Data Transmission Format (continued) (07h)
5 - 94 MP6000 BAR CODE PROGRAMMING GUIDE FN1 Substitution Values Key Category Parameter # 103 Decimal Value Parameter # 109 The wedge and USB HID keyboard hosts support a FN1 Substitution feature. Enabling this substitutes any FN1 character (0x1b) in an EAN128 bar code with a value. This value defaults to 7013 (Enter key). When using host commands to set the FN1 substitution value, set the key category parameter to 1, then set the 3-digit keystroke value.
USER PREFERENCES & MISCELLANEOUS OPTIONS 5 - 95 Copy Statistics to a Staging Flash Drive Parameter # 1137 If disabled, scan Enable Copy Statistics to a Staging Flash Drive to copy all data/configurations from the MP6000 to a staging USB flash drive. Refer to the MP6000 Integrator Guide (p/n 72E-172632-xx) for detailed information about the staging flash drive cloning. Options: • Disable Copy Statistics to a Staging Flash Drive • *Enable Copy Statistics to a Staging Flash Drive.
5 - 96 MP6000 BAR CODE PROGRAMMING GUIDE Copy Statistics to a Staging Flash Drive (continued) * Enable Copy Statistics to a Staging Flash Drive (01h)
CHAPTER 6 EAS PARAMETERS Introduction You can program the MP6000 to perform various functions, or activate different features. This chapter describes the EAS features, and provides programming bar codes for selecting these features. The MP6000 ships with the settings shown in Table 6-1 on page 6-2 (also see Appendix A, STANDARD DEFAULT PARAMETERS for all host device and miscellaneous defaults). If the default values suit requirements, programming is not necessary.
6-2 MP6000 BAR CODE PROGRAMMING GUIDE Scanning Sequence Examples In most cases, scanning one bar code sets the parameter value. For example, to set the Sensormatic Interlock Bar Code Mode to enable tag deactivation only after a bar code is decoded, scan Sensormatic Always Enable Deactivation Mode in the section, Sensormatic Always Enable Deactivation Mode on page 6-6. Other parameters, such as Sensormatic Deactivation Timeout, require scanning more than one bar code.
EAS PARAMETERS Table 6-1 EAS Parameter Defaults (Continued) Parameter Parameter Number Default Page Number Sensormatic Request Scan Time Message 1136 Enable 6-34 Checkpoint Interlock Polarity 983 Active Low 6-36 EAS Deactivation Override Button 981 Enable 6-38 6-3
6-4 MP6000 BAR CODE PROGRAMMING GUIDE EAS Operating Modes In addition to EAS preferences (also in this chapter) there are 10 EAS operating modes for the MP6000, listed below. EAS operating modes control whether or not EAS functionality is enabled, and is independent of whether or not EAS equipment is connected. It is the installer's responsibility to match these modes with the installed equipment.
EAS PARAMETERS 6-5 Operating Modes Parameter # 977 Sensormatic Auto Mode Sensormatic Auto Mode is dependent on the Scan Enable Time that the MP6000 reads from the Sensormatic ScanMax Pro control box (this value is set by Sensormatic in the control box during installation). If the Scan Enable Time equals 0 seconds, or 30 seconds, the MP6000 works in Sensormatic Scan Enable Interlock Mode (see page 6-10). Otherwise Scan Enable Time is from 1 second to 29 seconds.
6-6 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic Always Enable Deactivation Mode When Sensormatic Always Enable Deactivation Mode is scanned, tag deactivation is always enabled when the MP6000 is powered on. NOTE When the MP6000 is in Sensormatic Always Enable Deactivation mode, the tags are always deactivated by the MP6000 if the tags are in the deactivation field.
EAS PARAMETERS 6-7 Sensormatic Bar Code Interlock Mode Scan Sensormatic Bar Code Interlock Mode to enable tag deactivation only after a bar code is decoded. The tag deactivation time uses the time value set with Sensormatic Deactivation Timeout on page 6-15. NOTE Additional tags can be deactivated during the deactivation time if the tags are in the deactivation field.
6-8 MP6000 BAR CODE PROGRAMMING GUIDE Bar Code Auto Interlock Mode The MP6000 enables deactivation only when a bar code decodes. The deactivation state only lasts 1.2 seconds to avoid subsequent tag deactivation.
EAS PARAMETERS Bar Code Hold Off Mode Scan the bar code below to enable Hold Off mode. In this mode, if a tag is detected, bar codes are not decoded (no beep, no transmission to host) until the tag is deactivated. NOTE A bar code decode does not occur if a hard tag is detected, until the hard tag is removed from the detection field.
6 - 10 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic Scan Enable Interlock Mode When Sensormatic Scan Enable Interlock Mode is scanned, if the POS application sends a Scan Enable message to the MP6000, then the tag deactivated is enabled. If the POS application sends a Scan Disable message to the MP6000, then the tag deactivated is disabled.
EAS PARAMETERS 6 - 11 Checkpoint Bar Code Interlock Mode Scan Checkpoint Bar Code Interlock Mode to enable Checkpoint tag deactivation for 3 seconds after a bar code is decoded. The Checkpoint device controls all audible and visual feedback (the MP600 does not produce any audio and visual feedback for tag detection nor tag deactivation). This is also programmable inside the Checkpoint device by the Checkpoint installer.
6 - 12 MP6000 BAR CODE PROGRAMMING GUIDE Checkpoint Scan Enable Interlock Mode When Checkpoint Scan Enable Interlock Mode is scanned the following occurs: • Tag deactivation is active after the MP6000 receives a Scan Enable command from a host (POS application). • Tag deactivation is inactive after the MP6000 receives a Scan Disable command from a host (POS application). • Tag deactivation is enabled on power on.
EAS PARAMETERS 6 - 13 EAS LED On Mode Scan EAS LED On Mode to turn on the EAS LED. If there is EAS equipment, it controls the EAS tag detection and deactivation by itself.
6 - 14 MP6000 BAR CODE PROGRAMMING GUIDE EAS Disable Mode Parameter # 977 In this mode EAS tags are not detected, or deactivated.
EAS PARAMETERS 6 - 15 Sensormatic Deactivation Timeout Parameter # 982 This option determines the period of time in which EAS tag deactivation is allowed following a good bar code decode. This option only applies to Sensormatic Bar Code Interlock Mode on page 6-7. Scan Sensormatic Deactivation Timeout followed by two numeric bar codes from Appendix D, NUMERIC BAR CODES to set the EAS deactivation window to a time from 1 to 29 seconds. Single numerals must be preceded by a zero.
6 - 16 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic EAS Deactivation Parameter # 979 Options: • Sensormatic Disable EAS Deactivation - scan to prevent any soft tags from being deactivated. • *Sensormatic Enable EAS Deactivation - scan to allow soft tags to be deactivated.
EAS PARAMETERS 6 - 17 Sensormatic EAS Deactivation (continued) *Sensormatic Enable EAS Deactivation (01h)
6 - 18 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic EAS Beeps Scan a bar code in this section to set the audible alerts upon Sensormatic EAS tag detection, and/or deactivation. These modes have no affect if using Checkpoint equipment. In all cases (except when disabled) there are several types of beeps per bar code with a tag.
EAS PARAMETERS 6 - 19 Sensormatic EAS Beeps (continued) Sensormatic EAS Soft Tag Beeps Parameter # 984 Disable Soft Tag Beep (00h) NOTE When Disable Soft Tag Beep is scanned, no audible beep sounds when an EAS soft tag is deactivated.
6 - 20 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic EAS Beeps (continued) Sensormatic EAS Soft Tag Beep 1 When Senormatic EAS Soft Tag Beep 1 is scanned, a low tone short beep sounds when an EAS soft tag is deactivated.
EAS PARAMETERS 6 - 21 Sensormatic EAS Beeps (continued) Sensormatic EAS Soft Tag Beep 2 When Senormatic EAS Soft Tag Beep 2 is scanned, a low tone medium duration beep sounds when an EAS soft tag is deactivated.
6 - 22 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic EAS Beeps (continued) Sensormatic EAS Hard Tag Beeps Parameter # 985 Disable Hard Tag Beep (00h)
EAS PARAMETERS 6 - 23 Sensormatic EAS Beeps (continued) Scan Beep Indication Type 1 for a high tone short beep.
6 - 24 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic EAS Beeps (continued) Scan Beep Indication Type 2 for a high tone medium duration beep.
EAS PARAMETERS 6 - 25 Sensormatic EAS Beeps (continued) Sensormatic EAS Tag Detected Any Time Beep Parameter # 980 *Enable Detected Any Time Beep (01h)
6 - 26 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic EAS Beeps (continued) Disable Detected Any Time Beep (00h)
EAS PARAMETERS 6 - 27 Sensormatic EAS Beeps (continued) Sensormatic EAS Deactivation Fail Beep Parameter # 1213 *Disable Deactivation Fail Beep (00h)
6 - 28 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic EAS Beeps (continued) Enable Deactivation Fail Beep (01h)
EAS PARAMETERS 6 - 29 Sensormatic Request Messages There are three EAS message types (communication, high voltage, and enable scan time) that can be selected by scanning the EAS message parameters that follow. • Request Communication/Connection Message: Enabling this feature allows communication with the control box. • Request Voltage Message: Enabling this feature sends messages about dangerous voltage levels. • Request Scan Time Message: This message is only available in Auto Interlock Mode.
6 - 30 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic Request Communication/Connection Message Parameter # 978 *Enable Communication/Connection Message (01h)
EAS PARAMETERS 6 - 31 Sensormatic Request Communication/Connection Message (continued) Disable Communication/Connection Message (00h)
6 - 32 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic Request Voltage Message Parameter # 1130 *Enable Voltage Message (01h)
EAS PARAMETERS 6 - 33 Sensormatic Request Voltage Message (continued) Disable Voltage Message (00h)
6 - 34 MP6000 BAR CODE PROGRAMMING GUIDE Sensormatic Request Scan Time Message Parameter # 1136 *Enable Scan Time Message (01h)
EAS PARAMETERS 6 - 35 Sensormatic Request Scan Time Message (continued) Disable Scan Time Message (00h)
6 - 36 MP6000 BAR CODE PROGRAMMING GUIDE Checkpoint Interlock Polarity Parameter # 983 EAS Checkpoint Interlock Polarity determines the interlock pulse polarity required to deactivate a tag (the polarity must match the setting in the EAS control box). Options: • *Active Low - Tag deactivation is initiated by an active low pulse. • Active High - Tag deactivation is initiated by an active high pulse.
EAS PARAMETERS 6 - 37 Checkpoint Interlock Polarity (continued) Active High (01h)
6 - 38 MP6000 BAR CODE PROGRAMMING GUIDE Deactivation Override Button Parameter # 981 The EAS button on the MP6000 can be pressed to deactivate soft tags on items without decoding the bar code on the item. Options: • Disable EAS Deactivation Override Button - scan to disable the feature; pressing the EAS button has no effect. • *Enable EAS Deactivation Override Button - scan to activate the EAS button.
EAS PARAMETERS 6 - 39 Deactivation Override Button (continued) Disable Deactivation Override Button (00h)
6 - 40 MP6000 BAR CODE PROGRAMMING GUIDE
CHAPTER 7 AUXILIARY SCANNER BAR CODES Introduction The parameter bar codes in this chapter, and the bar code defaults in Table 7-1, are solely for the MP6000. These bar codes configure the MP6000 for connection to an auxiliary scanner. The auxiliary scanner requires its own configuration, and should be programmed with matching settings found in the auxiliary scanner’s Product Reference Guide.
7-2 MP6000 BAR CODE PROGRAMMING GUIDE Auxiliary Scanner Parameters Auxiliary Scanner Decode with Unknown Type If an auxiliary scanner is connected via SSI over RS-232 for Zebra scanners, HID Keyboard for non-Zebra scanners, or standard RS-232, and the Send Raw Decode Data option is enabled, the MP6000 transmits decode data with the code type set by this parameter. The default is value 1 (Send Unknown as Code 39).
AUXILIARY SCANNER BAR CODES Auxiliary Scanner Decode with Unknown Type (continued) Send Unknown as Code 128 (03h) 7-3
7-4 MP6000 BAR CODE PROGRAMMING GUIDE Auxiliary Scanner Decode with Unknown Type (continued) Send Unknown as PDF-417 (11h)
AUXILIARY SCANNER BAR CODES Auxiliary Scanner Decode with Unknown Type (continued) Send Unknown as Data Matrix (1Bh) 7-5
7-6 MP6000 BAR CODE PROGRAMMING GUIDE Host Type The MP6000 only supports standard RS-232, Wincor-Nixdorf B for non-Zebra scanners, and additionally SSI over RS-232 for Zebra scanners. Scan one of the bar codes that follow to select RS-232 as the host interface for the Zebra auxiliary scanner. Options: • Standard RS-232 • Wincor-Nixdorf RS-232 Mode B • * Zebra Scanner Auto Switch.
AUXILIARY SCANNER BAR CODES Host Type (continued) Wincor-Nixdorf RS-232 Mode B 7-7
7-8 MP6000 BAR CODE PROGRAMMING GUIDE Host Type (continued) Zebra Scanner Auto Switch Mode This mode only applies to Zebra RS-232 scanners. In this mode the MP6000 decides which protocol a scanner uses based on the primary host. For example, if the MP6000 is using SSI over CDC it automatically switches the auxiliary serial scanner to SSI over RS-232.
AUXILIARY SCANNER BAR CODES 7-9 Baud Rate Baud rate is the number of bits of data transmitted per second. Set the MP6000 baud rate to match the baud rate setting of the auxiliary scanner. Otherwise, data may not reach the host device or may reach it in distorted form. NOTE The MP6000 does not support baud rates below 9600. Options: • *Baud Rate 9600 • Baud Rate 19200 • Baud Rate 38400 • Baud Rate 115200 • Baud Rate 230400 • Baud Rate 460800 • Baud Rate 921600.
7 - 10 MP6000 BAR CODE PROGRAMMING GUIDE Baud Rate (continued) Baud Rate 19200
AUXILIARY SCANNER BAR CODES 7 - 11 Baud Rate (continued) Baud Rate 38400
7 - 12 MP6000 BAR CODE PROGRAMMING GUIDE Baud Rate (continued) Baud Rate 115200
AUXILIARY SCANNER BAR CODES 7 - 13 Baud Rate (continued) Baud Rate 230400
7 - 14 MP6000 BAR CODE PROGRAMMING GUIDE Baud Rate (continued) Baud Rate 460800
AUXILIARY SCANNER BAR CODES 7 - 15 Baud Rate (continued) Baud Rate 921600
7 - 16 MP6000 BAR CODE PROGRAMMING GUIDE Data Bits This parameter allows the MP6000 to interface with auxiliary scanners requiring a 7-bit or 8-bit ASCII protocol. Options: • 7 Data Bits • *8 Data Bits.
AUXILIARY SCANNER BAR CODES 7 - 17 Data Bits (continued) *8 Data Bits
7 - 18 MP6000 BAR CODE PROGRAMMING GUIDE Stop Bits The stop bit(s) at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream. Select the number of stop bits (one or two) based on the number the receiving terminal is programmed to accommodate. Set the number of stop bits to match auxiliary scanner requirements. Options: • Two Stops • *One Stop.
AUXILIARY SCANNER BAR CODES 7 - 19 Stop Bits (continued) *One Stop
7 - 20 MP6000 BAR CODE PROGRAMMING GUIDE Parity The stop bit(s) at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream. Select the number of stop bits (one or two) based on the number the receiving terminal is programmed to accommodate. Set the number of stop bits to match auxiliary scanner requirements. Options: • Even Parity • Odd Parity • *No Parity.
AUXILIARY SCANNER BAR CODES 7 - 21 Parity (continued) Odd Parity
7 - 22 MP6000 BAR CODE PROGRAMMING GUIDE Parity (continued) *No Parity
AUXILIARY SCANNER BAR CODES 7 - 23 Host RTS State This parameter sets the idle state of the auxiliary serial host RTS line. Scan a bar code below to select a Low RTS, or High RTS line state. Options: • High RTS • *Low RTS.
7 - 24 MP6000 BAR CODE PROGRAMMING GUIDE Host RTS State (continued) *Low RTS
CHAPTER 8 123SCAN2 Introduction 123Scan² is an easy to use, PC-based software tool that enables rapid customized setup of Zebra decoders. For detailed information about 123Scan², and how to use this utility to configure the MP6000, refer to the MP6000 Integrator Guide (p/n 72E-172632-xx). IMPORTANT When configuring the MP6000 by scanning a 2D programming bar code generated by 123Scan2, the only device programmed is the MP6000. If an MX101 (CSS) device, and/or an auxiliary scanner (e.g.
8-2 MP6000 BAR CODE PROGRAMMING GUIDE
CHAPTER 9 SSI INTERFACE Introduction Customers using RS-232 OPOS require the Simple Serial Interface (SSI), which provides a communications link between Zebra scanners, and a serial host. MP6000 includes a limited SSI implementation for special purposes. Contact the Zebra Customer Support Center online at: http://www.motorolasolutions.com/support, or call 1.800.653.5350 for more information. All communication between the decoder and host occurs over the hardware interface lines using the SSI protocol.
9-2 MP6000 BAR CODE PROGRAMMING GUIDE
CHAPTER 10SNAPI INTERFACE Introduction Customers using USB OPOS often require the USB-SNAPI Interface, which provides a communications link between Zebra scanners and a USB host. MP6000 includes a limited SNAPI implementation for special purposes. Contact the Zebra Customer Support Center online at: http://www.motorolasolutions.com/support, or call 1.800.653.5350 for more information. All communication between the decoder and host occurs over the hardware interface lines using the SNAPI protocol.
10 - 2 MP6000 BAR CODE PROGRAMMING GUIDE
CHAPTER 11SYMBOLOGIES Introduction This chapter describes symbology features and provides programming bar codes for selecting these features. To set feature values, scan a single bar code or a short bar code sequence. The settings are stored in non-volatile memory and are preserved even when the MP6000 powers down. Select a host type (see each host chapter for specific host information) after the power-up beeps sound. This is only necessary upon the first power-up when connected to a new host.
11 - 2 MP6000 BAR CODE PROGRAMMING GUIDE Symbology Parameter Defaults Table 11-1 lists the defaults for all symbologies parameters. To change the default values, scan the appropriate bar codes in this guide. These new values replace the standard default values in memory. To recall the default parameter values, scan the Set Default Parameter on page 5-4. NOTE See Appendix A, STANDARD DEFAULT PARAMETERS for all user preferences, hosts, and miscellaneous default parameters.
SYMBOLOGIES 11 - 3 Table 11-1 Parameter Defaults (Continued) Parameter Parameter Number Default Page Number Coerce UPC/EAN 915 Disable 11-62 UPC/EAN/JAN Supplemental Aim ID Format 672 Combined AIM ID, 1 Transmission 11-64 UCC Coupon Extended Code 85 Disable 11-67 Coupon Report 730 New Coupon Symbols 11-69 ISSN EAN 617 Disable 11-72 Code 128 8 Disable 11-73 Set Length(s) for Code 128 209, 210 Any Length 11-75 GS1-128 (formerly UCC/EAN-128) 14 Disable 11-80 ISBT 128 84
11 - 4 MP6000 BAR CODE PROGRAMMING GUIDE Table 11-1 Parameter Defaults (Continued) Parameter Parameter Number Default Page Number Code 93 9 Disable 11-126 Set Length(s) for Code 93 26, 27 Length Within Range: 4 to 55 11-128 Code 93 Stitching 1224 Disable 11-133 Code 93 Stitching Security Level 1216 Level 1 11-135 Code 93 Marginless Mode 1223 Disable 11-140 Interleaved 2 of 5 (ITF) 6 Disable 11-142 Set Lengths for I 2 of 5 22, 23 1 Length; Length = 14 11-144 I 2 of 5 Check
SYMBOLOGIES 11 - 5 Table 11-1 Parameter Defaults (Continued) Parameter Parameter Number Default Page Number Transmit MSI Check Digit 46 Disable 11-194 MSI Check Digit Algorithm 51 Mod 10/Mod 10 11-196 Chinese 2 of 5 408 Disable 11-198 Inverse 1D 586 Regular 11-200 GS1 DataBar (GS1 DataBar Omnidirectional, GS1 DataBar Truncated, GS1 DataBar Stacked, GS1 DataBar Stacked Omnidirectional) 338 Disable 11-203 GS1 DataBar Limited 339 Disable 11-205 GS1 DataBar Limited Security Level
11 - 6 MP6000 BAR CODE PROGRAMMING GUIDE Table 11-1 Parameter Defaults (Continued) Parameter Parameter Number Default Page Number MicroQR 573 Disable 11-249 Aztec 574 Disable 11-251 Aztec Inverse 589 Regular 11-253 Redundancy Level 78 1 11-256 Security Level (UPC/EAN and Code 93) 77 1 11-261 Intercharacter Gap Size 381 Normal 11-265 Symbology-Specific Security Levels Macro PDF Flush Macro PDF Buffer 11-267 Abort Macro PDF Entry 11-268
SYMBOLOGIES 11 - 7 Disable All Code Types To disable all symbologies, scan the bar code below. This is useful when enabling only a few code types.
11 - 8 MP6000 BAR CODE PROGRAMMING GUIDE UPC/EAN Enable/Disable UPC-A Parameter # 1 To enable or disable UPC-A, scan the appropriate bar code below. Options: • *Enable UPC-A • Disable UPC-A.
SYMBOLOGIES Enable/Disable UPC-A (continued) Disable UPC-A (00h) 11 - 9
11 - 10 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable UPC-E Parameter # 2 To enable or disable UPC-E, scan the appropriate bar code below. Options: • *Enable UPC-E • Disable UPC-E.
SYMBOLOGIES Enable/Disable UPC-E (continued) Disable UPC-E (00h) 11 - 11
11 - 12 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable UPC-E1 Parameter # 12 UPC-E1 is disabled by default. To enable or disable UPC-E1, scan the appropriate bar code below. NOTE UPC-E1 is not a UCC (Uniform Code Council) approved symbology. Options: • Enable UPC-E1 • *Disable UPC-E1.
SYMBOLOGIES Enable/Disable UPC-E1 (continued) *Disable UPC-E1 (00h) 11 - 13
11 - 14 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable EAN-8/JAN-8 Parameter # 4 To enable or disable EAN-8/JAN-8, scan the appropriate bar code below. Options: • *Enable EAN-8/JAN-8 • Disable EAN-8/JAN-8.
SYMBOLOGIES Enable/Disable EAN-8/JAN-8 (continued) Disable EAN-8/JAN-8 (00h) 11 - 15
11 - 16 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable EAN-13/JAN-13 Parameter # 3 To enable or disable EAN-13/JAN-13, scan the appropriate bar code below. Options: • *Enable EAN-13/JAN-13 • Disable EAN-13/JAN-13.
SYMBOLOGIES Enable/Disable EAN-13/JAN-13 (continued) Disable EAN-13/JAN-13 (00h) 11 - 17
11 - 18 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable Bookland EAN Parameter # 83 To enable or disable Bookland EAN, scan the appropriate bar code below. Options: • Enable Bookland EAN • *Disable Bookland EAN.
SYMBOLOGIES 11 - 19 Enable/Disable Bookland EAN (continued) *Disable Bookland EAN (00h) NOTE If Bookland EAN is enabled, select a Bookland ISBN Format on page 11-20. Also select either Decode UPC/EAN Supplementals, Autodiscriminate UPC/EAN Supplementals, or Enable 978/979 Supplemental Mode in Decode UPC/EAN/JAN Supplementals on page 11-22.
11 - 20 MP6000 BAR CODE PROGRAMMING GUIDE Bookland ISBN Format Parameter # 576 If Bookland EAN is enabled, select one of the following formats for Bookland data. Options: • *Bookland ISBN-10 - The MP6000 reports Bookland data starting with 978 in traditional 10-digit format with the special Bookland check digit for backward-compatibility. Data starting with 979 is not considered Bookland in this mode.
SYMBOLOGIES 11 - 21 Bookland ISBN Format (continued) Bookland ISBN-13 (01h) NOTE For Bookland EAN to function properly, ensure Bookland EAN is enabled (see Enable/Disable Bookland EAN on page 11-18), then select either Decode UPC/EAN Supplementals, Autodiscriminate UPC/EAN Supplementals, or Enable 978/979 Supplemental Mode in Decode UPC/EAN/JAN Supplementals on page 11-22.
11 - 22 MP6000 BAR CODE PROGRAMMING GUIDE Decode UPC/EAN/JAN Supplementals Parameter # 16 Supplementals are bar codes appended according to specific format conventions (e.g., UPC A+2, UPC E+2, EAN 13+2). Options: • Decode UPC/EAN/JAN with Supplementals - the MP6000 only decodes UPC/EAN symbols with supplemental characters, and ignores symbols without supplementals.
SYMBOLOGIES Decode UPC/EAN/JAN Supplementals (continued) Decode UPC/EAN/JAN Only With Supplementals (01h) 11 - 23
11 - 24 MP6000 BAR CODE PROGRAMMING GUIDE Decode UPC/EAN/JAN Supplementals (continued) *Ignore Supplementals (00h)
SYMBOLOGIES Decode UPC/EAN/JAN Supplementals (continued) Autodiscriminate UPC/EAN/JAN Supplementals (02h) 11 - 25
11 - 26 MP6000 BAR CODE PROGRAMMING GUIDE Decode UPC/EAN/JAN Supplementals (continued) Enable 378/379 Supplemental Mode (04h)
SYMBOLOGIES Decode UPC/EAN/JAN Supplementals (continued) Enable 978/979 Supplemental Mode (05h) 11 - 27
11 - 28 MP6000 BAR CODE PROGRAMMING GUIDE Decode UPC/EAN/JAN Supplementals (continued) Enable 977 Supplemental Mode (07h)
SYMBOLOGIES Decode UPC/EAN/JAN Supplementals (continued) Enable 414/419/434/439 Supplemental Mode (06h) 11 - 29
11 - 30 MP6000 BAR CODE PROGRAMMING GUIDE Decode UPC/EAN/JAN Supplementals (continued) Enable 491 Supplemental Mode (08h)
SYMBOLOGIES Decode UPC/EAN/JAN Supplementals (continued) Enable Smart Supplemental Mode (03h) 11 - 31
11 - 32 MP6000 BAR CODE PROGRAMMING GUIDE Decode UPC/EAN/JAN Supplementals (continued) Supplemental User-Programmable Type 1 (09h)
SYMBOLOGIES Decode UPC/EAN/JAN Supplementals (continued) Supplemental User-Programmable Type 1 and 2 (0Ah) 11 - 33
11 - 34 MP6000 BAR CODE PROGRAMMING GUIDE Decode UPC/EAN/JAN Supplementals (continued) Smart Supplemental Plus User-Programmable 1 (0Bh)
SYMBOLOGIES Decode UPC/EAN/JAN Supplementals (continued) Smart Supplemental Plus User-Programmable 1 and 2 (0Ch) 11 - 35
11 - 36 MP6000 BAR CODE PROGRAMMING GUIDE User-Programmable Supplementals Supplemental 1: Parameter # 579 Supplemental 2: Parameter # 580 Options: • If you selected a Supplemental User-Programmable option from Decode UPC/EAN/JAN Supplementals on page 11-22, select User-Programmable Supplemental 1 to set the 3-digit prefix. Then select the 3 digits using the numeric bar codes beginning on page D-1. • Select User-Programmable Supplemental 2 to set a second 3-digit prefix.
SYMBOLOGIES User-Programmable Supplementals (continued) User-Programmable Supplemental 2 11 - 37
11 - 38 MP6000 BAR CODE PROGRAMMING GUIDE UPC/EAN Redundancy Parameter # 1225 This option adjusts the number of additional times to decode a UPC/EAN symbol before decode data is transmitted. The range is from zero to five times. The default is 1. Scan UPC/EAN Redundancy below to set a decode redundancy value. Next, scan one numeric bar code in Appendix D, NUMERIC BAR CODES. Enter a leading zero for single digit numbers. To correct an error, or change a selection, scan Cancel on page D-11.
SYMBOLOGIES 11 - 39 UPC/EAN/JAN Supplemental Redundancy Parameter # 80 If you selected Autodiscriminate UPC/EAN/JAN Supplementals, this option adjusts the number of times to decode a symbol without supplementals before transmission. The range is from 2 to 25 times. Five or above is recommended when decoding a mix of UPC/EAN/JAN symbols with and without supplementals. The default is 10. Scan UPC/EAN/JAN Supplemental Redundancy below to set a decode redundancy value.
11 - 40 MP6000 BAR CODE PROGRAMMING GUIDE Transmit UPC-A Check Digit Parameter # 40 The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the UPC-A check digit. It is always verified to guarantee the integrity of the data. Options: • *Transmit UPC-A Check Digit • Do Not Transmit UPC-A Check Digit.
SYMBOLOGIES Transmit UPC-A Check Digit (continued) Do Not Transmit UPC-A Check Digit (00h) 11 - 41
11 - 42 MP6000 BAR CODE PROGRAMMING GUIDE Transmit UPC-E Check Digit Parameter # 41 The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the UPC-E check digit. It is always verified to guarantee the integrity of the data. Options: • *Transmit UPC-E Check Digit • Do Not Transmit UPC-E Check Digit.
SYMBOLOGIES Transmit UPC-E Check Digit (continued) Do Not Transmit UPC-E Check Digit (00h) 11 - 43
11 - 44 MP6000 BAR CODE PROGRAMMING GUIDE Transmit UPC-E1 Check Digit Parameter # 42 The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the UPC-E1 check digit. It is always verified to guarantee the integrity of the data. Options: • *Transmit UPC-E1 Check Digit • Do Not Transmit UPC-E1 Check Digit.
SYMBOLOGIES Transmit UPC-E1 Check Digit (continued) Do Not Transmit UPC-E1 Check Digit (00h) 11 - 45
11 - 46 MP6000 BAR CODE PROGRAMMING GUIDE UPC-A Preamble Parameter # 34 Preamble characters are part of the UPC symbol, and include Country Code and System Character. There are three options for transmitting a UPC-A preamble to the host device: transmit System Character only, transmit System Character and Country Code (“0” for USA), and transmit no preamble. Select the appropriate option to match the host system.
SYMBOLOGIES UPC-A Preamble (continued) *System Character ( ) (01h) 11 - 47
11 - 48 MP6000 BAR CODE PROGRAMMING GUIDE UPC-A Preamble (continued) System Character & Country Code (< COUNTRY CODE> ) (02h)
SYMBOLOGIES 11 - 49 UPC-E Preamble Parameter # 35 Preamble characters are part of the UPC symbol, and include Country Code and System Character. There are three options for transmitting a UPC-E preamble to the host device: transmit System Character only, transmit System Character and Country Code (“0” for USA), and transmit no preamble. Select the appropriate option to match the host system.
11 - 50 MP6000 BAR CODE PROGRAMMING GUIDE UPC-E Preamble (continued) *System Character ( ) (01h)
SYMBOLOGIES UPC-E Preamble (continued) System Character & Country Code (< COUNTRY CODE> ) (02h) 11 - 51
11 - 52 MP6000 BAR CODE PROGRAMMING GUIDE UPC-E1 Preamble Parameter # 36 Preamble characters are part of the UPC symbol, and include Country Code and System Character. There are three options for transmitting a UPC-E1 preamble to the host device: transmit System Character only, transmit System Character and Country Code (“0” for USA), and transmit no preamble. Select the appropriate option to match the host system.
SYMBOLOGIES UPC-E1 Preamble (continued) *System Character ( ) (01h) 11 - 53
11 - 54 MP6000 BAR CODE PROGRAMMING GUIDE UPC-E1 Preamble (continued) System Character & Country Code (< COUNTRY CODE> ) (02h)
SYMBOLOGIES 11 - 55 Convert UPC-E to UPC-A Parameter # 37 Enable this to convert UPC-E (zero suppressed) decoded data to UPC-A format before transmission. After conversion, the data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit). Disable this to transmit UPC-E decoded data as UPC-E data, without conversion. Options: • Convert UPC-E to UPC-A (Enable) • *Do Not Convert UPC-E to UPC-A (Disable).
11 - 56 MP6000 BAR CODE PROGRAMMING GUIDE Convert UPC-E to UPC-A (continued) *Do Not Convert UPC-E to UPC-A (Disable) (00h)
SYMBOLOGIES 11 - 57 Convert UPC-E1 to UPC-A Parameter # 38 Enable this to convert UPC-E1 decoded data to UPC-A format before transmission. After conversion, the data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit). Disable this to transmit UPC-E1 decoded data as UPC-E1 data, without conversion. Options: • Convert UPC-E1 to UPC-A (Enable) • *Do Not Convert UPC-E1 to UPC-A (Disable).
11 - 58 MP6000 BAR CODE PROGRAMMING GUIDE Convert UPC-E1 to UPC-A (continued) *Do Not Convert UPC-E1 to UPC-A (Disable) (00h)
SYMBOLOGIES 11 - 59 EAN-8/JAN-8 Extend Parameter # 39 Enable this parameter to add five leading zeros to decoded EAN-8 symbols to make them compatible in format to EAN-13 symbols. Disable this to transmit EAN-8 symbols as is. Options: • Enable EAN/JAN Zero Extend • *Disable EAN/JAN Zero Extend.
11 - 60 MP6000 BAR CODE PROGRAMMING GUIDE EAN-8/JAN-8 Extend (continued) *Disable EAN/JAN Zero Extend (00h)
SYMBOLOGIES Coerce UPC/EAN Parameter # 915 When disabled this parameter reports Coupon bar codes with a Coupon Symbol-ID. When enabled this parameter reports Coupon bar codes with a UPC Symbol-ID. Options: • Enable Coerce UPC/EAN • *Disable Coerce UPC/EAN.
11 - 62 MP6000 BAR CODE PROGRAMMING GUIDE Coerce UPC/EAN (continued) *Disable Coerce UPC/EAN (00h)
SYMBOLOGIES 11 - 63 UPC/EAN/JAN Supplemental AIM ID Format Parameter # 672 Scan a bar code to select one of the following options.
11 - 64 MP6000 BAR CODE PROGRAMMING GUIDE UPC/EAN/JAN Supplemental AIM ID Format (continued) *Combined AIM ID, 1 Transmission (01h)
SYMBOLOGIES UPC/EAN/JAN Supplemental AIM ID Format (continued) Separate AIM IDs, Separate Transmissions (02h) 11 - 65
11 - 66 MP6000 BAR CODE PROGRAMMING GUIDE UCC Coupon Extended Code Parameter # 85 Enable this parameter to decode UPC-A bar codes starting with digit ‘5’, EAN-13 bar codes starting with digit ‘99’, and UPC-A/GS1-128 Coupon Codes. UPCA, EAN-13, and GS1-128 must be enabled to scan all types of Coupon Codes. Options: • Enable UCC Coupon Extended Code • *Disable UCC Coupon Extended Code.
SYMBOLOGIES 11 - 67 UCC Coupon Extended Cod (continued) *Disable UCC Coupon Extended Code (00h) NOTE See UPC/EAN/JAN Supplemental Redundancy on page 11-39 to control autodiscrimination of the GS1-128 (right half) of a coupon code.
11 - 68 MP6000 BAR CODE PROGRAMMING GUIDE Coupon Report Parameter # 730 Traditional coupon symbols (old coupon symbols) are composed of two bar codes: UPC/EAN and Code128. A new coupon symbol is composed of a single Databar Expanded bar code. The new coupon format offers more options for purchase values (up to $999.99) and supports complex discount offers such as a second purchase requirement. An interim coupon symbol also exists that contains both types of bar codes: UPC/EAN and Databar Expanded.
SYMBOLOGIES Coupon Report (continued) *New Coupon Symbols (01h) 11 - 69
11 - 70 MP6000 BAR CODE PROGRAMMING GUIDE Coupon Report (continued) Both Coupon Formats (02h)
SYMBOLOGIES ISSN EAN Parameter # 617 Options: • Enable ISSN EAN • *Disable ISSN EAN.
11 - 72 MP6000 BAR CODE PROGRAMMING GUIDE ISSN EAN (continued) *Disable ISSN EAN (00h)
SYMBOLOGIES Code 128 Enable/Disable Code 128 Parameter # 8 Options: • Enable Code 128 • *Disable Code 128.
11 - 74 MP6000 BAR CODE PROGRAMMING GUIDE Code 128 (continued) *Disable Code 128 (00h)
SYMBOLOGIES 11 - 75 Set Lengths for Code 128 Parameter # L1 = 209, L2 = 210 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Code 128 to any length, one or two discrete lengths, or lengths within a specific range. NOTE When setting lengths for different bar code types, enter a leading zero for single digit numbers.
11 - 76 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Code 128 (continued) Code 128 - One Discrete Length
SYMBOLOGIES Set Lengths for Code 128 (continued) Code 128 - Two Discrete Lengths 11 - 77
11 - 78 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Code 128 (continued) Code 128 - Length Within Range
SYMBOLOGIES Set Lengths for Code 128 (continued) *Code 128 - Any Length 11 - 79
11 - 80 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable GS1-128 (formerly UCC/EAN-128) Parameter # 14 Options: • Enable GS1-128 • *Disable GS1-128.
SYMBOLOGIES Enable/Disable GS1-128 (formerly UCC/EAN-128) *Disable GS1-128 (00h) 11 - 81
11 - 82 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable ISBT 128 Parameter # 84 ISBT 128 is a variant of Code 128 used in the blood bank industry. Scan a bar code below to enable or disable ISBT 128. If necessary, the host must perform concatenation of the ISBT data. Options: • Enable ISBT 128 • *Disable ISBT 128.
SYMBOLOGIES Enable/Disable ISBT 128 (continued) *Disable ISBT 128 (00h) 11 - 83
11 - 84 MP6000 BAR CODE PROGRAMMING GUIDE ISBT Concatenation Parameter # 577 Select an option for concatenating pairs of ISBT code types: • *Disable ISBT Concatenation - The MP6000 does not concatenate pairs of ISBT codes it encounters. • Enable ISBT Concatenation - There must be two ISBT codes in order for the MP6000 to decode and perform concatenation. The MP6000 does not decode single ISBT symbols.
SYMBOLOGIES ISBT Concatenation (continued) Enable ISBT Concatenation (01h) 11 - 85
11 - 86 MP6000 BAR CODE PROGRAMMING GUIDE ISBT Concatenation (continued) Autodiscriminate ISBT Concatenation (02h)
SYMBOLOGIES 11 - 87 Check ISBT Table Parameter # 578 The ISBT specification includes a table that lists several types of ISBT bar codes that are commonly used in pairs. If you set ISBT Concatenation to Enable, enable Check ISBT Table to concatenate only those pairs found in this table. Other types of ISBT codes are not concatenated. Options: • *Enable Check ISBT Table • Disable Check ISBT Table.
11 - 88 MP6000 BAR CODE PROGRAMMING GUIDE Check ISBT Table (continued) Disable Check ISBT Table (00h)
SYMBOLOGIES 11 - 89 ISBT Concatenation Redundancy Parameter # 223 If you set ISBT Concatenation to Autodiscriminate, use this parameter to set the number of times the MP6000 must decode an ISBT symbol before determining that there is no additional symbol. Scan the bar code below, then scan two numeric bar codes in Appendix D, NUMERIC BAR CODES to set a value between 2 and 20. Enter a leading zero for single digit numbers. To correct an error or change a selection, scan Cancel on page D-11.
11 - 90 MP6000 BAR CODE PROGRAMMING GUIDE Code 128 Stitching Parameter # 72 This parameter enables/disables Code 128 stitching. Enabling this parameter is helpful for decoding longer bar codes. Options: • *Disable Code 128 Stitching • Enable Code 128 Stitching.
SYMBOLOGIES Code 128 Stitching (continued) Enable 11 - 91
11 - 92 MP6000 BAR CODE PROGRAMMING GUIDE Code 128 Stitching Security Level Parameter # 1205 This parameter sets the security level for Code 128 bar codes. Select increasing levels of security for decreasing levels of bar code quality. There is an inverse relationship between security, and digital scanner aggressiveness, so choose only that level of security necessary for any given application.
SYMBOLOGIES Code 128 Stitching Security Level (continued) Level 1 11 - 93
11 - 94 MP6000 BAR CODE PROGRAMMING GUIDE Code 128 Stitching Security Level (continued) Level 2
SYMBOLOGIES Code 128 Stitching Security Level (continued) Level 3 11 - 95
11 - 96 MP6000 BAR CODE PROGRAMMING GUIDE Code 128 Stitching Security Level (continued) Level 4
SYMBOLOGIES 11 - 97 Code 128 Marginless Mode Parameter # 1208 This parameter allows decoding a bar code with relaxed requirement regarding the size of clear margin around the bar code. Options: • *Disable Marginless Mode • Enable Marginless Mode.
11 - 98 MP6000 BAR CODE PROGRAMMING GUIDE Code 128 Marginless Mode (continued) Enable Marginless Mode
SYMBOLOGIES Enable/Disable Code 39 Parameter # 0 To enable or disable Code 39, scan the appropriate bar code below. Options: • Enable Code 39 • *Disable Code 39.
11 - 100 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable Code 39 (continued) *Disable Code 39 (00h) NOTE You cannot enable Trioptic Code 39 and Code 39 Full ASCII simultaneously.
SYMBOLOGIES 11 - 101 Enable/Disable Trioptic Code 39 Parameter # 13 Trioptic Code 39 is a variant of Code 39 used in the marking of computer tape cartridges. Trioptic Code 39 symbols always contain six characters. Options: • Enable Trioptic Code 39 • *Disable Trioptic Code 39.
11 - 102 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable Trioptic Code 39 (continued) *Disable Trioptic Code 39 (00h)
SYMBOLOGIES 11 - 103 Convert Code 39 to Code 32 Parameter # 86 Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. NOTE Code 39 must be enabled for this parameter to function. Options: • Enable Convert Code 39 to Code 32 • *Disable Convert Code 39 to Code 32.
11 - 104 MP6000 BAR CODE PROGRAMMING GUIDE Convert Code 39 to Code 32 (continued) *Disable Convert Code 39 to Code 32 (00h)
SYMBOLOGIES 11 - 105 Code 32 Prefix Parameter # 231 Scan the appropriate bar code below to enable or disable adding the prefix character “A” to all Code 32 bar codes. NOTE Convert Code 39 to Code 32 must be enabled for this parameter to function. Options: • Enable Code 32 Prefix • *Disable Code 32 Prefix.
11 - 106 MP6000 BAR CODE PROGRAMMING GUIDE Code 32 Prefix (continued) *Disable Code 32 Prefix (00h)
SYMBOLOGIES 11 - 107 Set Lengths for Code 39 Parameter # L1 = 18, L2 = 19 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Code 39 to any length, one or two discrete lengths, or lengths within a specific range. If Code 39 Full ASCII is enabled, Length Within a Range or Any Length are the preferred options. The range for Code 39 lengths is 0 - 55.
11 - 108 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Code 39 (continued) Code 39 - Two Discrete Lengths
SYMBOLOGIES 11 - 109 Set Lengths for Code 39 (continued) *Code 39 - Length Within Range
11 - 110 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Code 39 (continued) Code 39 - Any Length
SYMBOLOGIES 11 - 111 Code 39 Check Digit Verification Parameter # 48 Enable this feature to check the integrity of all Code 39 symbols to verify that the data complies with specified check digit algorithm. Only Code 39 symbols which include a modulo 43 check digit are decoded. Enable this feature if the Code 39 symbols contain a Modulo 43 check digit. Options: • Enable Code 39 Check Digit • *Disable Code 39 Check Digit.
11 - 112 MP6000 BAR CODE PROGRAMMING GUIDE Code 39 Check Digit Verification (continued) *Disable Code 39 Check Digit (00h)
SYMBOLOGIES 11 - 113 Transmit Code 39 Check Digit Parameter # 43 Scan a bar code below to transmit Code 39 data with or without the check digit. Options: • Transmit Code 39 Check Digit (Enable) • *Do Not Transmit Code 39 Check Digit (Disable).
11 - 114 MP6000 BAR CODE PROGRAMMING GUIDE Transmit Code 39 Check Digit (continued) *Do Not Transmit Code 39 Check Digit (Disable) (00h) NOTE Code 39 Check Digit Verification must be enabled for this parameter to function.
SYMBOLOGIES 11 - 115 Code 39 Full ASCII Conversion Parameter # 17 Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set. To enable or disable Code 39 Full ASCII, scan the appropriate bar code below. Options: • Enable Code 39 Full ASCII • *Disable Code 39 Full ASCII.
11 - 116 MP6000 BAR CODE PROGRAMMING GUIDE Code 39 Full ASCII Conversion (continued) *Disable Code 39 Full ASCII (00h) NOTE You cannot enable Trioptic Code 39 and Code 39 Full ASCII simultaneously. Code 39 Full ASCII to Full ASCII Correlation is host-dependent, and is therefore described in the ASCII Character Set Table for the appropriate interface. See the Character Sets on page E-1.
SYMBOLOGIES 11 - 117 Code 39 Stitching Parameter # 70 This parameter enables/disables Code 39 stitching. Enabling this parameter is helpful for decoding longer bar codes. Options: • Enable Code 39 Stitching • *Disable Code 39 Stitching.
11 - 118 MP6000 BAR CODE PROGRAMMING GUIDE Code 39 Stitching (continued) Enable
SYMBOLOGIES 11 - 119 Code 39 Stitching Security Level Parameter # 1206 This parameter sets the security level for Code 39 bar codes. Select increasing levels of security for decreasing levels of bar code quality. There is an inverse relationship between security, and digital scanner aggressiveness, so choose only that level of security necessary for any given application.
11 - 120 MP6000 BAR CODE PROGRAMMING GUIDE Code 39 Stitching Security Level (continued) Level 1
SYMBOLOGIES 11 - 121 Code 39 Stitching Security Level (continued) Level 2
11 - 122 MP6000 BAR CODE PROGRAMMING GUIDE Code 39 Stitching Security Level (continued) Level 3
SYMBOLOGIES 11 - 123 Code 39 Stitching Security Level (continued) Level 4
11 - 124 MP6000 BAR CODE PROGRAMMING GUIDE Code 39 Marginless Mode Parameter # 1209 This parameter allows decoding a bar code with relaxed requirement regarding the size of clear margin around the bar code. Options: • Enable Marginless Mode • *Disable Marginless Mode.
SYMBOLOGIES 11 - 125 Code 39 Marginless Mode (continued) Enable Marginless Mode
11 - 126 MP6000 BAR CODE PROGRAMMING GUIDE Code 93 Enable/Disable Code 93 Parameter # 9 To enable or disable Code 93, scan the appropriate bar code below.
SYMBOLOGIES 11 - 127 Code 93 (continued) *Disable Code 93 (00h)
11 - 128 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Code 93 Parameter # L1 = 26, L2 = 27 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Code 93 to any length, one or two discrete lengths, or lengths within a specific range. The range for Code 93 lengths is 0 - 55. Options: • Code 93 One Discrete Length - Select this option to decode only Code 93 symbols containing a selected length.
SYMBOLOGIES 11 - 129 Set Lengths for Code 93 (continued) Code 93 - One Discrete Length
11 - 130 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Code 93 (continued) Code 93 - Two Discrete Lengths
SYMBOLOGIES 11 - 131 Set Lengths for Code 93 (continued) *Code 93 - Length Within Range
11 - 132 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Code 93 (continued) Code 93 - Any Length
SYMBOLOGIES 11 - 133 Code 93 Stitching Parameter # 1224 This parameter enables Code 93 stitching. This is helpful for decoding longer bar codes. Options: • Enable Code 93 Stitching • *Disable Code 93 Stitching.
11 - 134 MP6000 BAR CODE PROGRAMMING GUIDE Code 93 Stitching (continued) Enable
SYMBOLOGIES 11 - 135 Code 93 Stitching Security Level Parameter # 1216 This parameter sets the security level for Code 93 bar codes. Select increasing levels of security for decreasing levels of bar code quality. There is an inverse relationship between security, and digital scanner aggressiveness, so choose only that level of security necessary for any given application.
11 - 136 MP6000 BAR CODE PROGRAMMING GUIDE Code 93 Stitching Security Level (continued) *Level 1
SYMBOLOGIES 11 - 137 Code 93 Stitching Security Level (continued) Level 2
11 - 138 MP6000 BAR CODE PROGRAMMING GUIDE Code 93 Stitching Security Level (continued) Level 3
SYMBOLOGIES 11 - 139 Code 93 Stitching Security Level (continued) Level 4
11 - 140 MP6000 BAR CODE PROGRAMMING GUIDE Code 93 Marginless Mode Parameter # 1223 This parameter allows decoding a bar code with relaxed requirement regarding the size of clear margin around the bar code. Options: • Enable Marginless Mode • *Disable Marginless Mode.
SYMBOLOGIES 11 - 141 Code 93 Marginless Mode (continued) Enable Marginless Mode
11 - 142 MP6000 BAR CODE PROGRAMMING GUIDE Interleaved 2 of 5 (ITF) Enable/Disable Interleaved 2 of 5 Parameter # 6 To enable or disable Interleaved 2 of 5, scan the appropriate bar code below, and select an Interleaved 2 of 5 length from the following pages. Options: • Enable Interleaved 2 of 5 • *Disable Interleaved 2 of 5.
SYMBOLOGIES 11 - 143 Interleaved 2 of 5 (ITF) (continued) *Disable Interleaved 2 of 5 (00h)
11 - 144 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Interleaved 2 of 5 (I 2 of 5) Parameter # L1 = 22, L2 = 23 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for I 2 of 5 to any length, one or two discrete lengths, or lengths within a specific range. The range for Interleaved 2 of 5 lengths is 0 - 55.
SYMBOLOGIES 11 - 145 Set Lengths for Interleaved 2 of 5 (continued) *I 2 of 5 - One Discrete Length
11 - 146 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Interleaved 2 of 5 (continued) I 2 of 5 - Two Discrete Lengths
SYMBOLOGIES 11 - 147 Set Lengths for Interleaved 2 of 5 (continued) I 2 of 5 - Length Within Range
11 - 148 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Interleaved 2 of 5 (continued) I 2 of 5 - Any Length
SYMBOLOGIES 11 - 149 I 2 of 5 Check Digit Verification Parameter # 49 Enable this feature to check the integrity of all I 2 of 5 symbols to verify the data complies with either the specified Uniform Symbology Specification (USS), or the Optical Product Code Council (OPCC) check digit algorithm. Options: • *Disable I 2 of 5 Check Digit Verification • USS Check Digit • OPCC Check Digit.
11 - 150 MP6000 BAR CODE PROGRAMMING GUIDE I 2 of 5 Check Digit Verification (continued) USS Check Digit (01h)
SYMBOLOGIES 11 - 151 I 2 of 5 Check Digit Verification (continued) OPCC Check Digit (02h)
11 - 152 MP6000 BAR CODE PROGRAMMING GUIDE Transmit I 2 of 5 Check Digit Parameter # 44 Scan the appropriate bar code below to transmit I 2 of 5 data with or without the check digit. Options: • Transmit I 2 of 5 Check Digit (Enable) • *Do Not Transmit I 2 of 5 Check Digit (Disable).
SYMBOLOGIES 11 - 153 Transmit I 2 of 5 Check Digit (continued) *Do Not Transmit I 2 of 5 Check Digit (Disable) (00h)
11 - 154 MP6000 BAR CODE PROGRAMMING GUIDE Convert I 2 of 5 to EAN-13 Parameter # 82 Enable this parameter to convert 14-character I 2 of 5 codes to EAN-13, and transmit to the host as EAN-13. To accomplish this, the I 2 of 5 code must be enabled, and the code must have a leading zero and a valid EAN-13 check digit. Options: • Convert I 2 of 5 to EAN-13 (Enable) • *Do Not Convert I 2 of 5 to EAN-13 (Disable).
SYMBOLOGIES 11 - 155 Convert I 2 of 5 to EAN-13 (continued) *Do Not Convert I 2 of 5 to EAN-13 (Disable) (00h)
11 - 156 MP6000 BAR CODE PROGRAMMING GUIDE Interleaved 2 of 5 Stitching Parameter # 1204 This parameter enables Interleaved 2 of 5 stitching. This helpful for decoding longer bar codes. Options: • Enable Interleaved 2 of 5 Stitching • *Disable Interleaved 2 of 5 Stitching.
SYMBOLOGIES 11 - 157 Interleaved 2 of 5 Stitching (continued) Enable
11 - 158 MP6000 BAR CODE PROGRAMMING GUIDE Interleaved 2 of 5 Stitching Security Level Parameter # 1207 This parameter sets the security level for Interleaved 2 of 5 bar codes. Select increasing levels of security for decreasing levels of bar code quality. There is an inverse relationship between security and digital scanner aggressiveness, so choose only that level of security necessary for any given application.
SYMBOLOGIES 11 - 159 Interleaved 2 of 5 Stitching Security Level (continued) *Level 1
11 - 160 MP6000 BAR CODE PROGRAMMING GUIDE Interleaved 2 of 5 Stitching Security Level (continued) Level 2
SYMBOLOGIES 11 - 161 Interleaved 2 of 5 Stitching Security Level (continued) Level 3
11 - 162 MP6000 BAR CODE PROGRAMMING GUIDE Interleaved 2 of 5 Stitching Security Level (continued) Level 4
SYMBOLOGIES 11 - 163 Interleaved 2 of 5 Marginless Mode Parameter # 1210 This parameter allows decoding a bar code with relaxed requirement regarding the size of clear margin around the bar code Options: • Enable Marginless Mode • *Disable Marginless Mode.
11 - 164 MP6000 BAR CODE PROGRAMMING GUIDE Interleaved 2 of 5 Marginless Mode (continued) Enable Marginless Mode
SYMBOLOGIES 11 - 165 Discrete 2 of 5 (DTF/D 2 of 5) Enable/Disable Discrete 2 of 5 Parameter # 5 Options: • Enable Discrete 2 of 5 • *Disable Discrete 2 of 5.
11 - 166 MP6000 BAR CODE PROGRAMMING GUIDE Discrete 2 of 5 (DTF) (continued) *Disable Discrete 2 of 5 (00h)
SYMBOLOGIES 11 - 167 Set Lengths for Discrete 2 of 5 Parameter # L1 = 20, L2 = 21 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for D 2 of 5 to any length, one or two discrete lengths, or lengths within a specific range. The range for Discrete 2 of 5 lengths is 0 - 55. Options: • *D 2 of 5 One Discrete Length - Select this option to decode only D 2 of 5 symbols containing a selected length.
11 - 168 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Discrete 2 of 5 (continued) *D 2 of 5 - One Discrete Length
SYMBOLOGIES 11 - 169 Set Lengths for Discrete 2 of 5 (continued) D 2 of 5 - Two Discrete Lengths
11 - 170 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Discrete 2 of 5 (continued) D 2 of 5 - Length Within Range
SYMBOLOGIES 11 - 171 Set Lengths for Discrete 2 of 5 (continued) D 2 of 5 - Any Length
11 - 172 MP6000 BAR CODE PROGRAMMING GUIDE Codabar (NW - 7) Enable/Disable Codabar Parameter # 7 Options: • Enable Codabar • *Disable Codabar.
SYMBOLOGIES 11 - 173 Codabar (NW - 7) (continued) *Disable Codabar (00h)
11 - 174 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Codabar Parameter # L1 = 24, L2 = 25 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Codabar to any length, one or two discrete lengths, or lengths within a specific range. The range for Codabar lengths is 5 - 55. Options: • Codabar One Discrete Length - Select this option to decode only Codabar symbols containing a selected length.
SYMBOLOGIES 11 - 175 Set Lengths for Codabar (continued) Codabar - One Discrete Length
11 - 176 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Codabar (continued) Codabar - Two Discrete Lengths
SYMBOLOGIES 11 - 177 Set Lengths for Codabar (continued) *Codabar - Length Within Range
11 - 178 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for Codabar (continued) Codabar - Any Length
SYMBOLOGIES 11 - 179 CLSI Editing Parameter # 54 Enable this parameter to strip the start and stop characters and insert a space after the first, fifth, and tenth characters of a 14-character Codabar symbol. Enable this feature if the host system requires this data format. NOTE Symbol length does not include start and stop characters. Options: • Enable CLSI Editing • *Disable CLSI Editing.
11 - 180 MP6000 BAR CODE PROGRAMMING GUIDE CLSI Editing (continued) *Disable CLSI Editing (00h)
SYMBOLOGIES 11 - 181 NOTIS Editing Parameter # 55 Enable this parameter to strip the start and stop characters from a decoded Codabar symbol. Enable this feature if the host system requires this data format. Options: • Enable NOTIS Editing • *Disable NOTIS Editing.
11 - 182 MP6000 BAR CODE PROGRAMMING GUIDE NOTIS Editing (continued) *Disable NOTIS Editing (00h)
SYMBOLOGIES 11 - 183 Codabar Upper or Lower Case Start/Stop Characters Detection Parameter # 855 Select whether to detect upper case or lower case Codabar start/stop characters. Options: • Upper Case • *Lower Case.
11 - 184 MP6000 BAR CODE PROGRAMMING GUIDE Codabar Upper or Lower Case Start/Stop Characters Detection (continued) *Lower Case (01h)
SYMBOLOGIES 11 - 185 MSI Enable/Disable MSI Parameter # 11 Options: • Enable MSI • *Disable MSI.
11 - 186 MP6000 BAR CODE PROGRAMMING GUIDE MSI (continued) *Disable MSI (00h)
SYMBOLOGIES 11 - 187 Set Lengths for MSI Parameter # L1 = 30, L2 = 31 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for MSI to any length, one or two discrete lengths, or lengths within a specific range. Options: • MSI One Discrete Length - Select this option to decode only MSI symbols containing a selected length. Select the length using the numeric bar codes in Appendix D, NUMERIC BAR CODES.
11 - 188 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for MSI (continued) NOTE Due to the construction of the MSI symbology, it is possible for a scan line covering only a portion of the code to transmit as a complete scan, yielding less data than is encoded in the bar code. To prevent this, select specific lengths (MSI - One Discrete Length, Two Discrete Lengths) for MSI applications.
SYMBOLOGIES 11 - 189 Set Lengths for MSI (continued) MSI - Two Discrete Lengths
11 - 190 MP6000 BAR CODE PROGRAMMING GUIDE Set Lengths for MSI (continued) *MSI - Length Within Range
SYMBOLOGIES 11 - 191 Set Lengths for MSI (continued) MSI - Any Length
11 - 192 MP6000 BAR CODE PROGRAMMING GUIDE MSI Check Digits Parameter # 50 With MSI symbols, one check digit is mandatory and always verified by the reader. The second check digit is optional. If the MSI codes include two check digits, scan the Two MSI Check Digits bar code to enable verification of the second check digit. See MSI Check Digit Algorithm on page 11-196 for the selection of second digit algorithms. Options: • *One MSI Check Digit • Two MSI Check Digits.
SYMBOLOGIES 11 - 193 MSI Check Digits (continued) Two MSI Check Digits (01h)
11 - 194 MP6000 BAR CODE PROGRAMMING GUIDE Transmit MSI Check Digit(s) Parameter # 46 Scan a bar code below to transmit MSI data with or without the check digit. Options: • Transmit MSI Check Digit(s) (Disable) • *Do Not Transmit MSI Check Digit(s) (Disable).
SYMBOLOGIES 11 - 195 Transmit MSI Check Digit(s) (continued) *Do Not Transmit MSI Check Digit(s) (Disable) (00h)
11 - 196 MP6000 BAR CODE PROGRAMMING GUIDE MSI Check Digit Algorithm Parameter # 51 Two algorithms are possible for the verification of the second MSI check digit. Select the bar code below corresponding to the algorithm used to encode the check digit. Options: • MOD 10/MOD 11 • *MOD 10/MOD 10.
SYMBOLOGIES 11 - 197 MSI Check Digit Algorithm (continued) *MOD 10/MOD 10 (01h)
11 - 198 MP6000 BAR CODE PROGRAMMING GUIDE Chinese 2 of 5 Enable/Disable Chinese 2 of 5 Parameter # 408 Options: • Enable Chinese 2 of 5 • *Disable Chinese 2 of 5.
SYMBOLOGIES 11 - 199 Chinese 2 of 5 (continued) *Disable Chinese 2 of 5 (00h)
11 - 200 MP6000 BAR CODE PROGRAMMING GUIDE Inverse 1D Parameter # 586 This parameter sets the 1D inverse decoder setting. Options: • *Regular Only - the MP6000 decodes regular 1D bar codes only. • Inverse Only - the MP6000 decodes inverse 1D bar codes only. • Inverse Autodetect - the MP6000 decodes both regular and inverse 1D bar codes.
SYMBOLOGIES 11 - 201 Inverse 1D (continued) Inverse Only (01h)
11 - 202 MP6000 BAR CODE PROGRAMMING GUIDE Inverse 1D (continued) Inverse Autodetect (02h)
SYMBOLOGIES 11 - 203 GS1 DataBar Parameter # 338 When Enable GS1 DataBar is scanned, the following GS1 DataBar types are supported: • GS1 DataBar Omnidirectional • GS1 DataBar Truncated • GS1 DataBar Stacked • GS1 DataBar Stacked Omnidirectional.
11 - 204 MP6000 BAR CODE PROGRAMMING GUIDE GS1 DataBar (continued) *Disable GS1 DataBar (00h)
SYMBOLOGIES 11 - 205 GS1 DataBar Limited Parameter # 339 Options: • Enable GS1 DataBar Limited • *Disable GS1 DataBar Limited.
11 - 206 MP6000 BAR CODE PROGRAMMING GUIDE GS1DataBar Limited (continued) *Disable GS1 DataBar Limited (00h)
SYMBOLOGIES 11 - 207 GS1 DataBar Expanded Parameter # 340 When Enable GS1 DataBar Expanded is scanned, the following GS1 DataBar Expanded types are supported: • GS1 DataBar Expanded • GS1 DataBar Expanded Stacked. Options: • Enable GS1 DataBar Expanded • *Disable GS1 DataBar Expanded.
11 - 208 MP6000 BAR CODE PROGRAMMING GUIDE GS1 DataBar Expanded (continued) *Disable GS1 DataBar Expanded (00h)
SYMBOLOGIES 11 - 209 GS1 DataBar Limited Security Level Parameter # 728 The MP6000 offers four levels of decode security for GS1 DataBar Limited bar codes. There is an inverse relationship between security and digital scanner aggressiveness. Increasing the level of security may result in reduced aggressiveness in scanning, so only choose the level of security necessary. • Level 1 - No clear margin required.
11 - 210 MP6000 BAR CODE PROGRAMMING GUIDE GS1 DataBar Limited Security Level (continued) Security Level 2 (02h)
SYMBOLOGIES 11 - 211 GS1 DataBar Limited Security Level (continued) *Security Level 3 (03h)
11 - 212 MP6000 BAR CODE PROGRAMMING GUIDE GS1 DataBar Limited Security Level (continued) Security Level 4 (04h)
SYMBOLOGIES 11 - 213 Convert GS1 DataBar to UPC/EAN Parameter # 397 This parameter only applies to GS1 DataBar and GS1 DataBar Limited symbols not decoded as part of a Composite symbol. Enable this to strip the leading '010' from DataBar and DataBar Limited symbols encoding a single zero as the first digit, and report the bar code as EAN-13. For bar codes beginning with two or more zeros but not six zeros, this parameter strips the leading '0100' and reports the bar code as UPC-A.
11 - 214 MP6000 BAR CODE PROGRAMMING GUIDE Convert GS1 DataBar to UPC/EAN (continued) *Disable Convert GS1 DataBar to UPC/EAN (00h)
SYMBOLOGIES 11 - 215 Composite Composite CC-C Parameter # 341 Options: • Enable CC-C • *Disable CC-C.
11 - 216 MP6000 BAR CODE PROGRAMMING GUIDE Composite (continued) *Disable CC-C (00h)
SYMBOLOGIES 11 - 217 Composite CC-A/B Parameter # 342 Scan a bar code below to enable or disable Composite bar codes of type CC-A/B. NOTE If you enable this code type, also see UPC Composite Mode on page 11-221. Options: • Enable CC-A/B • *Disable CC-A/B.
11 - 218 MP6000 BAR CODE PROGRAMMING GUIDE Composite CC-A/B (continued) *Disable CC-A/B (00h)
SYMBOLOGIES 11 - 219 Composite TLC-39 Parameter # 371 Scan a bar code below to enable or disable Composite bar codes of type TLC-39. Options: • Enable TLC39 • *Disable TLC39.
11 - 220 MP6000 BAR CODE PROGRAMMING GUIDE Composite TLC-39 (continued) *Disable TLC39 (00h)
SYMBOLOGIES 11 - 221 UPC Composite Mode Parameter # 344 If you enable Composite CC-A/B on page 11-217, select an option for linking UPC symbols with a 2D symbol during transmission as if they were one symbol. Options: • *UPC Never Linked - Transmit UPC bar codes regardless of whether a 2D symbol is detected. • UPC Always Linked - Transmit UPC bar codes and the 2D portion. If 2D is not present, the UPC bar code does not transmit.
11 - 222 MP6000 BAR CODE PROGRAMMING GUIDE UPC Composite Mode (continued) UPC Always Linked (01h)
SYMBOLOGIES 11 - 223 UPC Composite Mode (continued) Autodiscriminate UPC Composites (02h)
11 - 224 MP6000 BAR CODE PROGRAMMING GUIDE Composite Beep Mode Parameter # 398 To select the number of decode beeps when a composite bar code is decoded, scan the appropriate bar code. Options: • Single Beep After Both are Decoded • *Beep as Each Code Type is Decoded • Double Beep After Both are Decoded.
SYMBOLOGIES 11 - 225 Composite Beep Mode (continued) *Beep as Each Code Type is Decoded (01h)
11 - 226 MP6000 BAR CODE PROGRAMMING GUIDE Composite Beep Mode (continued) Double Beep After Both are Decoded (02h)
SYMBOLOGIES 11 - 227 GS1-128 Emulation Mode for UCC/EAN Composite Codes Parameter # 427 Options: • Enable GS1-128 Emulation Mode for UCC/EAN Composite Codes • *Disable GS1-128 Emulation Mode for UCC/EAN Composite Codes.
11 - 228 MP6000 BAR CODE PROGRAMMING GUIDE GS1-128 Emulation Mode for UCC/EAN Composite Codes (continued) *Disable GS1-128 Emulation Mode for UCC/EAN Composite Codes (00h)
SYMBOLOGIES 11 - 229 2D Symbologies Enable/Disable PDF417 Parameter # 15 Enable or disable PDF417. Options: • Enable PDF417 • *Disable PDF417.
11 - 230 MP6000 BAR CODE PROGRAMMING GUIDE 2D Symbologies (continued) *Disable PDF417 (00h)
SYMBOLOGIES 11 - 231 Enable/Disable MicroPDF417 Parameter # 227 Enable or disable MicroPDF417. Options: • Enable MicroPDF417 • *Disable MicroPDF417.
11 - 232 MP6000 BAR CODE PROGRAMMING GUIDE Enable/Disable MicroPDF417 (continued) *Disable MicroPDF417 (00h)
SYMBOLOGIES 11 - 233 Code 128 Emulation Parameter # 123 Enable this parameter to transmit data from certain MicroPDF417 symbols as Code 128. AIM Code ID Character (01h) on page 5-80 must be enabled for this parameter to work.
11 - 234 MP6000 BAR CODE PROGRAMMING GUIDE Code 128 Emulation (continued) *Disable Code 128 Emulation (00h)
SYMBOLOGIES 11 - 235 Data Matrix Parameter # 292 Options: • Enable Data Matrix • *Disable Data Matrix.
11 - 236 MP6000 BAR CODE PROGRAMMING GUIDE Data Matrix (continued) *Disable Data Matrix (00h)
SYMBOLOGIES 11 - 237 Data Matrix Inverse Parameter # 588 This parameter sets the Data Matrix inverse decoder setting. Options: • *Regular Only - The MP6000 decodes regular Data Matrix bar codes only. • Inverse Only - The MP6000 decodes inverse Data Matrix bar codes only. • Inverse Autodetect - The MP6000 decodes both regular and inverse Data Matrix bar codes.
11 - 238 MP6000 BAR CODE PROGRAMMING GUIDE Data Matrix Inverse (continued) Inverse Only (01h)
SYMBOLOGIES 11 - 239 Data Matrix Inverse (continued) Inverse Autodetect (02h)
11 - 240 MP6000 BAR CODE PROGRAMMING GUIDE GS1 Data Matrix Parameter # 1336 Enable or disable GS1 Data Matrix. Options: • Enable • *Disable.
SYMBOLOGIES 11 - 241 GS1 Data Matrix *Disable GS1 Data Matrix (00h)
11 - 242 MP6000 BAR CODE PROGRAMMING GUIDE QR Code Parameter # 293 Enable or disable QR Code. Options: • Enable QR Code • *Disable QR Code.
SYMBOLOGIES 11 - 243 QR Code (continued) *Disable QR Code (00h)
11 - 244 MP6000 BAR CODE PROGRAMMING GUIDE QR Inverse Parameter # 587 This parameter sets the QR inverse decoder setting. Options: • *Regular Only - the MP6000 decodes regular QR bar codes only. • Inverse Only - the MP6000 decodes inverse QR bar codes only. • Inverse Autodetect - the MP6000 decodes both regular and inverse QR bar codes.
SYMBOLOGIES 11 - 245 QR Inverse (continued) Inverse Only (01h)
11 - 246 MP6000 BAR CODE PROGRAMMING GUIDE QR Inverse (continued) Inverse Autodetect (02h)
SYMBOLOGIES 11 - 247 GS1 QR Parameter # 1343 Enable or disable GS1 QR. Options: • Enable GS1 QR • *Disable GS1 QR.
11 - 248 MP6000 BAR CODE PROGRAMMING GUIDE GS1 QR (continued) *Disable GS1 QR (00h)
SYMBOLOGIES 11 - 249 MicroQR Parameter # 573 Enable or disable MicroQR. Options: • Enable MicroQR • *Disable MicroQR.
11 - 250 MP6000 BAR CODE PROGRAMMING GUIDE MicroQR (continued) *Disable MicroQR (00h)
SYMBOLOGIES 11 - 251 Aztec Parameter # 574 Enable or disable Aztec. Options: • Enable Aztec • *Disable Aztec.
11 - 252 MP6000 BAR CODE PROGRAMMING GUIDE Aztec (continued) *Disable Aztec (00h)
SYMBOLOGIES 11 - 253 Aztec Inverse Parameter # 589 This parameter sets the Aztec inverse decoder setting. Options: • *Regular Only - the MP6000 decodes regular Aztec bar codes only. • Inverse Only - the MP6000 decodes inverse Aztec bar codes only. • Inverse Autodetect - the MP6000 decodes both regular and inverse Aztec bar codes.
11 - 254 MP6000 BAR CODE PROGRAMMING GUIDE Aztec Inverse (continued) Inverse Only (01h)
SYMBOLOGIES 11 - 255 Aztec Inverse (continued) Inverse Autodetect (02h)
11 - 256 MP6000 BAR CODE PROGRAMMING GUIDE Redundancy Level Parameter # 78 The MP6000 offers four levels of decode redundancy. Select higher redundancy levels for decreasing levels of bar code quality. As redundancy levels increase, the MP6000’s aggressiveness decreases. Select the redundancy level appropriate for the bar code quality. Options: • *Redundancy Level 1 • Redundancy Level 2 • Redundancy Level 3 • Redundancy Level 4.
SYMBOLOGIES 11 - 257 Redundancy Level (continued) *Redundancy Level 1 (01h)
11 - 258 MP6000 BAR CODE PROGRAMMING GUIDE Redundancy Level (continued) Redundancy Level 2 (02h)
SYMBOLOGIES 11 - 259 Redundancy Level (continued) Redundancy Level 3 (03h)
11 - 260 MP6000 BAR CODE PROGRAMMING GUIDE Redundancy Level (continued) Redundancy Level 4 (04h)
SYMBOLOGIES 11 - 261 Security Level Parameter # 77 The MP6000 offers four levels of decode security for delta bar codes, which include UPC/EAN and Code 93. Select increasing levels of security for decreasing levels of bar code quality. There is an inverse relationship between security and digital scanner aggressiveness, so choose only that level of security necessary for any given application.
11 - 262 MP6000 BAR CODE PROGRAMMING GUIDE Security Level (continued) *Security Level 1 (01h)
SYMBOLOGIES 11 - 263 Security Level (continued) Security Level 2 (02h)
11 - 264 MP6000 BAR CODE PROGRAMMING GUIDE Security Level (continued) Security Level 3 (03h)
SYMBOLOGIES 11 - 265 Intercharacter Gap Size Parameter # 381 The Code 39 and Codabar symbologies have an intercharacter gap that is typically quite small. Due to various bar code-printing technologies, this gap can grow larger than the maximum size allowed, preventing the MP6000 from decoding the symbol. If this problem occurs, scan the Large Intercharacter Gaps parameter to tolerate these out-of-specification bar codes. Options: • *Normal Intercharacter Gaps • Large Intercharacter Gaps.
11 - 266 MP6000 BAR CODE PROGRAMMING GUIDE Intercharacter Gap Size (continued) Large Intercharacter Gaps (0Ah)
SYMBOLOGIES 11 - 267 Macro PDF Features Macro PDF is a special feature for concatenating multiple PDF symbols into one file. The scanner can decode symbols that are encoded with this feature, and can store more than 64 Kb of decoded data stored in up to 50 MacroPDF symbols. CAUTION When printing, keep each Macro PDF sequence separate, as each sequence has unique identifiers. Do not mix bar codes from several Macro PDF sequences, even if they encode the same data.
11 - 268 MP6000 BAR CODE PROGRAMMING GUIDE Abort Macro PDF Entry This clears all currently-stored Macro PDF data in the buffer without transmission and aborts from Macro PDF mode.
CHAPTER 12 DRIVER’S LICENSE SET UP Introduction The MP6000 is capable of parsing out information from standard US driver's licenses and certain other American Association of Motor Vehicle Administrators (AAMVA) compliant ID cards. This is achieved using internally embedded algorithms, where scanning bar codes activates algorithms internally embedded in the digital scanner to produce formatted data. Use the formatted data for age verification, credit card application information, and more.
12 - 2 MP6000 BAR CODE PROGRAMMING GUIDE Table 12-1 DL Parsing Parameter Table (Continued) Parameter Default AAMVA Parse Field Bar Codes Page Number N/A 12-21 Set Default Parameter N/A 12-91 Output Gender as M or F N/A 12-92 Date Format CCYYMMDD 12-93 N/A 12-106 AAMVA Issuer ID Full Name Last Name First Name Middle Name / Initial Name Suffix Name Prefix Mailing Address Line 1 Mailing Address Line 2 Mailing Address City Mailing Address State Mailing Address Postal Code Home Address Line 1
DRIVER’S LICENSE SET UP 12 - 3 Table 12-1 DL Parsing Parameter Table (Continued) Parameter Default Keyboard Characters Send Space Send ! Send " Send # Send $ Send % Send & Send ' Send ( Send ) Send * Send + Send , Send Send .
12 - 4 MP6000 BAR CODE PROGRAMMING GUIDE Table 12-1 DL Parsing Parameter Table (Continued) Parameter Embedded Driver’s License Parsing ADF Example When the sample bar codes are scanned in the numbered sequence this example creates a parsing rule for parsed data configured to result in the format: Last Name, First Name.
DRIVER’S LICENSE SET UP 12 - 5 Driver’s License Parsing To enable driver's license parsing on the digital scanner, scan the Embedded Driver's License Parsing bar code. This does not require Zebra software (.DLL). Scan the bar codes on the following pages in the order indicating the sequence of data fields that the digital scanner outputs. See Parsing Driver’s License Data Fields (Embedded Driver's License Parsing) on page 12-7 for more information.
12 - 6 MP6000 BAR CODE PROGRAMMING GUIDE Embedded Driver’s License Parsing Embedded Driver’s License Parsing
DRIVER’S LICENSE SET UP 12 - 7 Parsing Driver’s License Data Fields (Embedded Driver's License Parsing) To begin programming a parsing rule: 1. Scan Begin New Driver’s License Parse Rule on page 12-8. 2. Scan any of the field bar codes on the following pages, or Send Keystroke (Control Characters and Keyboard Characters) on page 12-106 to complete the parsing rule. 3. After entering the entire rule, scan Save Driver’s License Parse Rule on page 12-9 to save the rule.
12 - 8 MP6000 BAR CODE PROGRAMMING GUIDE Driver’s License Parse Field Bar Codes Begin New Driver’s License Parse Rule
DRIVER’S LICENSE SET UP Driver’s License Parse Field Bar Codes (continued) Save Driver’s License Parse Rule 12 - 9
12 - 10 MP6000 BAR CODE PROGRAMMING GUIDE Driver’s License Parse Field Bar Codes (continued) Quit Entering Driver’s License Rule
DRIVER’S LICENSE SET UP Driver’s License Parse Field Bar Codes (continued) Erase Driver’s License Parse Rules 12 - 11
12 - 12 MP6000 BAR CODE PROGRAMMING GUIDE Driver’s License Parse Field Bar Codes (continued) The parse fields currently supported begin below. Not all IDs present data in the same format. For example, some IDs may have separate fields for first name, last name, and middle initial, and others may have a single field with the entire name. In addition, some IDs may expire on the subject's birth date and the actual expiration date field may only indicate the year.
DRIVER’S LICENSE SET UP Driver’s License Parse Field Bar Codes (continued) Middle Name/Initial 12 - 13
12 - 14 MP6000 BAR CODE PROGRAMMING GUIDE Driver’s License Parse Field Bar Codes (continued) Last Name
DRIVER’S LICENSE SET UP Driver’s License Parse Field Bar Codes (continued) Name Suffix 12 - 15
12 - 16 MP6000 BAR CODE PROGRAMMING GUIDE Driver’s License Parse Field Bar Codes (continued) Name Prefix
DRIVER’S LICENSE SET UP Driver’s License Parse Field Bar Codes (continued) Expiration Date 12 - 17
12 - 18 MP6000 BAR CODE PROGRAMMING GUIDE Driver’s License Parse Field Bar Codes (continued) Birth Date
DRIVER’S LICENSE SET UP Driver’s License Parse Field Bar Codes (continued) Issue Date 12 - 19
12 - 20 MP6000 BAR CODE PROGRAMMING GUIDE Driver’s License Parse Field Bar Codes (continued) ID Number (Formatted)
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes AAMVA Issuer ID 12 - 21
12 - 22 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Full Name
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Last Name 12 - 23
12 - 24 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) First Name
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Middle Name / Initial 12 - 25
12 - 26 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Name Suffix
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Name Prefix 12 - 27
12 - 28 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Mailing Address Line 1
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Mailing Address Line 2 12 - 29
12 - 30 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Mailing Address City
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Mailing Address State 12 - 31
12 - 32 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Mailing Address Postal Code
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Home Address Line 1 12 - 33
12 - 34 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Home Address Line 2
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Home Address City 12 - 35
12 - 36 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Home Address State
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Home Address Postal Code 12 - 37
12 - 38 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) License ID Number
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) License Class 12 - 39
12 - 40 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) License Restrictions
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) License Endorsements 12 - 41
12 - 42 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Height (Feet and/or Inches)
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Height (Centimeters) 12 - 43
12 - 44 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Weight (Pounds)
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Weight (Kilograms) 12 - 45
12 - 46 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Eye Color
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Hair Color 12 - 47
12 - 48 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) License Expiration Date
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Birth Date 12 - 49
12 - 50 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Gender
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) License Issue Date 12 - 51
12 - 52 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) License Issue State
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Social Security Number 12 - 53
12 - 54 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Permit Class
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Permit Expiration Date 12 - 55
12 - 56 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Permit ID Number
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Permit Issue Date 12 - 57
12 - 58 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Permit Restrictions
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Permit Endorsements 12 - 59
12 - 60 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) AKA Social Security Name
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) AKA Full Name 12 - 61
12 - 62 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) AKA Last Name
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) AKA First Name 12 - 63
12 - 64 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) AKA Middle Name / Initial
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) AKA Name Suffix 12 - 65
12 - 66 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) AKA Name Prefix
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) AKA Birth Date 12 - 67
12 - 68 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Issue Timestamp
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Number of Duplicates 12 - 69
12 - 70 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Medical Codes
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Organ Donor 12 - 71
12 - 72 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Nonresident
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Customer ID 12 - 73
12 - 74 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Weight Range
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Document Discriminator 12 - 75
12 - 76 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Country
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Federal Commission Codes 12 - 77
12 - 78 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Place of Birth
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Audit Information 12 - 79
12 - 80 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Inventory Control
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Race / Ethnicity 12 - 81
12 - 82 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Std Vehicle Class
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Std Endorsements 12 - 83
12 - 84 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Std Restrictions
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Class Description 12 - 85
12 - 86 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Endorsement Description
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Restrictions Description 12 - 87
12 - 88 MP6000 BAR CODE PROGRAMMING GUIDE AAMVA Parse Field Bar Codes (continued) Height in Inches
DRIVER’S LICENSE SET UP AAMVA Parse Field Bar Codes (continued) Height in Centimeters 12 - 89
12 - 90 MP6000 BAR CODE PROGRAMMING GUIDE Parser Version ID Bar Codes Include this field to emit embedded parser software version identification.
DRIVER’S LICENSE SET UP User Preferences Set Default Parameter Scan this bar code to return all parameters to the default values listed in Table A-1 on page A-1.
12 - 92 MP6000 BAR CODE PROGRAMMING GUIDE Output Gender as M or F Scan this bar code to report the gender as M or F instead of a numeric value.
DRIVER’S LICENSE SET UP 12 - 93 Date Format Use these bar codes to select the date format that is displayed. Date fields include the following: • CCYY = 4-digit year (CC=2-digit century [00-99], YY=2-digit year in the century [00-99]) • MM = 2-digit month [01-12] • DD = 2-digit day of the month [00-31] The default is Date Format CCYYMMDD. NOTE To specify a date separator, i.e.
12 - 94 MP6000 BAR CODE PROGRAMMING GUIDE Date Format (continued) CCYYDDMM
DRIVER’S LICENSE SET UP Date Format (continued) MMDDCCYY 12 - 95
12 - 96 MP6000 BAR CODE PROGRAMMING GUIDE Date Format (continued) MMCCYYDD
DRIVER’S LICENSE SET UP Date Format (continued) DDMMCCYY 12 - 97
12 - 98 MP6000 BAR CODE PROGRAMMING GUIDE Date Format (continued) DDCCYYMM
DRIVER’S LICENSE SET UP Date Format (continued) YYMMDD 12 - 99
12 - 100 MP6000 BAR CODE PROGRAMMING GUIDE Date Format (continued) YYDDMM
DRIVER’S LICENSE SET UP 12 - 101 Date Format (continued) MMDDYY
12 - 102 MP6000 BAR CODE PROGRAMMING GUIDE Date Format (continued) MMYYDD
DRIVER’S LICENSE SET UP 12 - 103 Date Format (continued) DDMMYY
12 - 104 MP6000 BAR CODE PROGRAMMING GUIDE Date Format (continued) DDYYMM
DRIVER’S LICENSE SET UP 12 - 105 Date Format (continued) No Separator Scan this bar code immediately following a date format bar code to use no separator character between the date fields.
12 - 106 MP6000 BAR CODE PROGRAMMING GUIDE Send Keystroke (Control Characters and Keyboard Characters) Control Characters Scan a Send bar code for the keystroke to send.
DRIVER’S LICENSE SET UP 12 - 107 Control Characters (continued) Send Control B
12 - 108 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control C
DRIVER’S LICENSE SET UP 12 - 109 Control Characters (continued) Send Control D
12 - 110 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control E
DRIVER’S LICENSE SET UP 12 - 111 Control Characters (continued) Send Control F
12 - 112 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control G
DRIVER’S LICENSE SET UP 12 - 113 Control Characters (continued) Send Control H
12 - 114 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control I
DRIVER’S LICENSE SET UP 12 - 115 Control Characters (continued) Send Control J
12 - 116 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control K
DRIVER’S LICENSE SET UP 12 - 117 Control Characters (continued) Send Control L
12 - 118 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control M
DRIVER’S LICENSE SET UP 12 - 119 Control Characters (continued) Send Control N
12 - 120 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control O
DRIVER’S LICENSE SET UP 12 - 121 Control Characters (continued) Send Control P
12 - 122 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control Q
DRIVER’S LICENSE SET UP 12 - 123 Control Characters (continued) Send Control R
12 - 124 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control S
DRIVER’S LICENSE SET UP 12 - 125 Control Characters (continued) Send Control T
12 - 126 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control U
DRIVER’S LICENSE SET UP 12 - 127 Control Characters (continued) Send Control V
12 - 128 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control W
DRIVER’S LICENSE SET UP 12 - 129 Control Characters (continued) Send Control X
12 - 130 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control Y
DRIVER’S LICENSE SET UP 12 - 131 Control Characters (continued) Send Control Z
12 - 132 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control [
DRIVER’S LICENSE SET UP 12 - 133 Control Characters (continued) Send Control \
12 - 134 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control ]
DRIVER’S LICENSE SET UP 12 - 135 Control Characters (continued) Send Control 6
12 - 136 MP6000 BAR CODE PROGRAMMING GUIDE Control Characters (continued) Send Control -
DRIVER’S LICENSE SET UP 12 - 137 Keyboard Characters Scan a Send bar code for the keyboard characters to send.
12 - 138 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send !
DRIVER’S LICENSE SET UP 12 - 139 Keyboard Characters (continued) Send “
12 - 140 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send #
DRIVER’S LICENSE SET UP 12 - 141 Keyboard Characters (continued) Send $
12 - 142 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send %
DRIVER’S LICENSE SET UP 12 - 143 Keyboard Characters (continued) Send &
12 - 144 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send ‘
DRIVER’S LICENSE SET UP 12 - 145 Keyboard Characters (continued) Send (
12 - 146 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send )
DRIVER’S LICENSE SET UP 12 - 147 Keyboard Characters (continued) Send *
12 - 148 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send +
DRIVER’S LICENSE SET UP 12 - 149 Keyboard Characters (continued) Send ,
12 - 150 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send -
DRIVER’S LICENSE SET UP 12 - 151 Keyboard Characters (continued) Send .
12 - 152 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send /
DRIVER’S LICENSE SET UP 12 - 153 Keyboard Characters (continued) Send 0
12 - 154 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send 1
DRIVER’S LICENSE SET UP 12 - 155 Keyboard Characters (continued) Send 2
12 - 156 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send 3
DRIVER’S LICENSE SET UP 12 - 157 Keyboard Characters (continued) Send 4
12 - 158 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send 5
DRIVER’S LICENSE SET UP 12 - 159 Keyboard Characters (continued) Send 6
12 - 160 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send 7
DRIVER’S LICENSE SET UP 12 - 161 Keyboard Characters (continued) Send 8
12 - 162 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send 9
DRIVER’S LICENSE SET UP 12 - 163 Keyboard Characters (continued) Send :
12 - 164 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send ;
DRIVER’S LICENSE SET UP 12 - 165 Keyboard Characters (continued) Send <
12 - 166 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send =
DRIVER’S LICENSE SET UP 12 - 167 Keyboard Characters (continued) Send >
12 - 168 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send ?
DRIVER’S LICENSE SET UP 12 - 169 Keyboard Characters (continued) Send @
12 - 170 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send A
DRIVER’S LICENSE SET UP 12 - 171 Keyboard Characters (continued) Send B
12 - 172 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send C
DRIVER’S LICENSE SET UP 12 - 173 Keyboard Characters (continued) Send D
12 - 174 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send E
DRIVER’S LICENSE SET UP 12 - 175 Keyboard Characters (continued) Send F
12 - 176 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send G
DRIVER’S LICENSE SET UP 12 - 177 Keyboard Characters (continued) Send H
12 - 178 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send I
DRIVER’S LICENSE SET UP 12 - 179 Keyboard Characters (continued) Send J
12 - 180 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send K
DRIVER’S LICENSE SET UP 12 - 181 Keyboard Characters (continued) Send L
12 - 182 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send M
DRIVER’S LICENSE SET UP 12 - 183 Keyboard Characters (continued) Send N
12 - 184 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send O
DRIVER’S LICENSE SET UP 12 - 185 Keyboard Characters (continued) Send P
12 - 186 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send Q
DRIVER’S LICENSE SET UP 12 - 187 Keyboard Characters (continued) Send R
12 - 188 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send S
DRIVER’S LICENSE SET UP 12 - 189 Keyboard Characters (continued) Send T
12 - 190 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send U
DRIVER’S LICENSE SET UP 12 - 191 Keyboard Characters (continued) Send V
12 - 192 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send W
DRIVER’S LICENSE SET UP 12 - 193 Keyboard Characters (continued) Send X
12 - 194 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send Y
DRIVER’S LICENSE SET UP 12 - 195 Keyboard Characters (continued) Send Z
12 - 196 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send [
DRIVER’S LICENSE SET UP 12 - 197 Keyboard Characters (continued) Send \
12 - 198 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send ]
DRIVER’S LICENSE SET UP 12 - 199 Keyboard Characters (continued) Send ^
12 - 200 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send _
DRIVER’S LICENSE SET UP 12 - 201 Keyboard Characters (continued) Send `
12 - 202 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send a
DRIVER’S LICENSE SET UP 12 - 203 Keyboard Characters (continued) Send b
12 - 204 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send c
DRIVER’S LICENSE SET UP 12 - 205 Keyboard Characters (continued) Send d
12 - 206 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send e
DRIVER’S LICENSE SET UP 12 - 207 Keyboard Characters (continued) Send f
12 - 208 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send g
DRIVER’S LICENSE SET UP 12 - 209 Keyboard Characters (continued) Send h
12 - 210 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send i
DRIVER’S LICENSE SET UP 12 - 211 Keyboard Characters (continued) Send j
12 - 212 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send k
DRIVER’S LICENSE SET UP 12 - 213 Keyboard Characters (continued) Send l
12 - 214 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send m
DRIVER’S LICENSE SET UP 12 - 215 Keyboard Characters (continued) Send n
12 - 216 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send o
DRIVER’S LICENSE SET UP 12 - 217 Keyboard Characters (continued) Send p
12 - 218 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send q
DRIVER’S LICENSE SET UP 12 - 219 Keyboard Characters (continued) Send r
12 - 220 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send s
DRIVER’S LICENSE SET UP 12 - 221 Keyboard Characters (continued) Send t
12 - 222 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send u
DRIVER’S LICENSE SET UP 12 - 223 Keyboard Characters (continued) Send v
12 - 224 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send w
DRIVER’S LICENSE SET UP 12 - 225 Keyboard Characters (continued) Send x
12 - 226 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send y
DRIVER’S LICENSE SET UP 12 - 227 Keyboard Characters (continued) Send z
12 - 228 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send {
DRIVER’S LICENSE SET UP 12 - 229 Keyboard Characters (continued) Send |
12 - 230 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send }
DRIVER’S LICENSE SET UP 12 - 231 Keyboard Characters (continued) Send ~
12 - 232 MP6000 BAR CODE PROGRAMMING GUIDE Keyboard Characters (continued) Send Tab Key
DRIVER’S LICENSE SET UP 12 - 233 Keyboard Characters (continued) Send Enter Key
12 - 234 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example Scan the following bar codes in sequence to program the scanner to extract and transmit first, middle, and last names; mailing address line 1; mailing address line 2; mailing address city; mailing address state; mailing address postal code; and, date of birth. Then, scan a driver’s license bar code. NOTE This example applies to RS-232.
DRIVER’S LICENSE SET UP 12 - 235 Parsing Rule Example (continued) 2 Begin New Driver’s License Parse Rule
12 - 236 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 3 First Name
DRIVER’S LICENSE SET UP 12 - 237 Parsing Rule Example (continued) 4 Send Space
12 - 238 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 5 Middle Name / Initial
DRIVER’S LICENSE SET UP 12 - 239 Parsing Rule Example (continued) 6 Send Space
12 - 240 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 7 Last Name
DRIVER’S LICENSE SET UP 12 - 241 Parsing Rule Example (continued) 8 Send Enter Key
12 - 242 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 9 Mailing Address Line 1
DRIVER’S LICENSE SET UP 12 - 243 Parsing Rule Example (continued) 10 Send Space
12 - 244 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 11 Mailing Address Line 2
DRIVER’S LICENSE SET UP 12 - 245 Parsing Rule Example (continued) 12 Send Enter Key
12 - 246 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 13 Mailing Address City
DRIVER’S LICENSE SET UP 12 - 247 Parsing Rule Example (continued) 14 Send Space
12 - 248 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 15 Mailing Address State
DRIVER’S LICENSE SET UP 12 - 249 Parsing Rule Example (continued) 16 Send Space
12 - 250 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 17 Mailing Address Postal Code
DRIVER’S LICENSE SET UP 12 - 251 Parsing Rule Example (continued) 18 Send Enter Key
12 - 252 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 19 Birth Date
DRIVER’S LICENSE SET UP 12 - 253 Parsing Rule Example (continued) 20 Send Enter Key
12 - 254 MP6000 BAR CODE PROGRAMMING GUIDE Parsing Rule Example (continued) 21 Save Driver’s Licence Parse Rule
DRIVER’S LICENSE SET UP 12 - 255 Embedded Driver's License Parsing ADF Example This example creates a parsing rule for parsed data configured to result in the format: Last Name, First Name 1 Begin New Driver’s License Parse Rule
12 - 256 MP6000 BAR CODE PROGRAMMING GUIDE Embedded Driver's License Parsing ADF Example (continued) 2 Last Name
DRIVER’S LICENSE SET UP 12 - 257 Embedded Driver's License Parsing ADF Example (continued) 3 Send ,
12 - 258 MP6000 BAR CODE PROGRAMMING GUIDE Embedded Driver's License Parsing ADF Example (continued) 4 Send Space
DRIVER’S LICENSE SET UP 12 - 259 Embedded Driver's License Parsing ADF Example (continued) 5 First Name
12 - 260 MP6000 BAR CODE PROGRAMMING GUIDE Embedded Driver's License Parsing ADF Example (continued) 6 Save Driver’s Licence Parse Rule
DRIVER’S LICENSE SET UP 12 - 261 Embedded Driver's License Parsing ADF Example (continued) Then, in order to limit the full name to 15 characters, create the following ADF rule: 1 Begin New Rule
12 - 262 MP6000 BAR CODE PROGRAMMING GUIDE Embedded Driver's License Parsing ADF Example (continued) 2 Criterion: Parsed Driver's License
DRIVER’S LICENSE SET UP 12 - 263 Embedded Driver's License Parsing ADF Example (continued) 3 Action: Send Next 15 Characters
12 - 264 MP6000 BAR CODE PROGRAMMING GUIDE Embedded Driver's License Parsing ADF Example (continued) 4 Save Rule For a license belonging to Michael Williams, the parsed data is Williams, Michael and Williams, Micha after applying the previous ADF rule.
CHAPTER 13ADVANCED DATA FORMATTING Introduction Advanced Data Formatting (ADF) is a means of customizing data before transmission to the host device. Use ADF to edit scan data to suit requirements. Implement ADF by scanning a related series of bar codes which program the MP6000 with ADF rules. For information and programming bar codes for ADF, refer to the Advanced Data Formatting Programmer Guide, p/n 72E-69680-xx.
13 - 2 MP6000 BAR CODE PROGRAMMING GUIDE
APPENDIX A STANDARD DEFAULT PARAMETERS Standard Default Parameters Table Table A-1 Parameter Parameter Number Default Page Number USB Host Parameters USB Device Type IBM Table Top 1-3 USB Country Keyboard Types - Country Codes North American Standard USB Keyboard 1-9 USB Keystroke Delay No Delay 1-14 Simulated Caps Lock Disable 1-17 USB CAPS Lock Override Disable 1-20 Scan Disable Mode Full Disable 1-21 USB Ignore Unknown Characters Enable 1-24 USB Convert Unknown to Code 39 Disa
A-2 MP6000 BAR CODE PROGRAMMING GUIDE Standard Default Parameters Table (Continued) Table A-1 Parameter Parameter Number Default Page Number USB HID Polling Interval 8 msec 1-52 Fast HID Keyboard Disable 1-55 Quick Keypad Emulation Disable 1-57 2-byte - Extended Scale Status Disabled 1-59 Version 2.
STANDARD DEFAULT PARAMETERS A-3 Standard Default Parameters Table (Continued) Table A-1 Parameter Parameter Number Default Page Number Ignore Beep Directive Ignore 3-14 Ignore Configuration Directive Ignore 3-16 1214 Full Disable 3-17 Legal Scale Units 995 n/a 4-3 Legal Scale Dampening Filter Setting 996 Low Vibration Sensitivity 4-6 Scale Enable 1197 Enable 4-9 Scale Reset 6009 n/a 4-11 Scale Display Configuration 986 Disable 4-13 Scale Enforce Zero Return 987 Disable
A-4 MP6000 BAR CODE PROGRAMMING GUIDE Standard Default Parameters Table (Continued) Table A-1 Parameter Parameter Number Default Page Number Swipe Frame Timeout 1226 15 ms 5-33 Presentation Frame Timeout 1227 35 ms 5-34 Cell Phone Frame Timeout 1228 35 ms 5-35 PDF Prioritization 719 Disable 5-40 PDF Prioritization Timeout 720 300 ms 5-42 Center Object Detect 1128 Enable 5-44 Center IR Sensitivity 1219 Medium 5-46 Stitching Type 1229 Swipe Stitching 5-48 Scanning Usage
STANDARD DEFAULT PARAMETERS A-5 Standard Default Parameters Table (Continued) Table A-1 Parameter Parameter Number Default Page Number Miscellaneous Parameters Sensormatic Deactivation Timeout 982 10 sec 6-15 Sensormatic EAS Deactivation 979 Enable 6-17 Sensormatic Soft Tag Beeps 984 Soft Tag Beep 1 6-20 Sensormatic Hard Tag Beeps 985 Hard Tag Beep 1 6-23 Sensormatic Detected Any Time Beep 980 Enable 6-25 Sensormatic Deactivation Fail Beep 1213 Disable 6-27 Sensormatic Reques
A-6 MP6000 BAR CODE PROGRAMMING GUIDE Standard Default Parameters Table (Continued) Table A-1 Parameter Parameter Number Default Page Number Bookland EAN 83 Disable 11-19 Bookland ISBN Format 576 ISBN-10 11-20 Decode UPC/EAN/JAN Supplementals (2 and 5 digits) 16 Ignore 11-24 n/a 11-36 User-Programmable Supplementals Supplemental 1: Supplemental 2: 579 580 UPC/EAN Redundancy 1225 1 11-38 UPC/EAN/JAN Supplemental Redundancy 80 10 11-39 Transmit UPC-A Check Digit 40 Enable 11
STANDARD DEFAULT PARAMETERS A-7 Standard Default Parameters Table (Continued) Table A-1 Parameter Parameter Number Default Page Number ISBT Concatenation Redundancy 223 10 11-89 Code 128 Stitching 72 Disable 11-90 Code 128 Stitching Security Level 1205 0 11-92 Code 128 Marginless Mode 1208 Disable 11-97 Code 39 0 Disable 11-100 Trioptic Code 39 13 Disable 11-102 Convert Code 39 to Code 32 (Italian Pharmacy Code) 86 Disable 11-104 Code 32 Prefix 231 Disable 11-106 Set
A-8 MP6000 BAR CODE PROGRAMMING GUIDE Standard Default Parameters Table (Continued) Table A-1 Parameter Parameter Number Default Page Number Convert I 2 of 5 to EAN 13 82 Disable 11-155 ITF Stitching 1204 Disable 11-156 ITF Stitching Security Level 1207 Level 1 11-159 ITF Marginless Mode 1210 Disable 11-163 Discrete 2 of 5 5 Disable 11-166 Set Length(s) for D 2 of 5 20, 21 1 Length; Length = 12 11-168 Codabar 7 Disable 11-173 Set Lengths for Codabar 24, 25 Length Within
STANDARD DEFAULT PARAMETERS A-9 Standard Default Parameters Table (Continued) Table A-1 Parameter Parameter Number Default Page Number GS1 DataBar Limited Security Level 728 3 11-211 Convert GS1 DataBar to UPC/EAN 397 Disable 11-214 Composite CC-C 341 Disable 11-216 Composite CC-A/B 342 Disable 11-218 Composite TLC-39 371 Disable 11-220 UPC Composite Mode 344 Never Linked 11-221 Composite Beep Mode 398 Beep As Each Code Type is Decoded 11-225 GS1-128 Emulation Mode for UC
A - 10 MP6000 BAR CODE PROGRAMMING GUIDE Standard Default Parameters Table (Continued) Table A-1 Parameter Parameter Number Default Page Number Macro PDF Flush Macro PDF Buffer n/a 11-267 Abort Macro PDF Entry n/a 11-268 1 User selection is required to configure this interface and this is the most common selection.
APPENDIX B PROGRAMMING REFERENCE Symbol Code Identifiers Table B-1 Symbol Code Characters Code Character Code Type A UPC-A, UPC-E, UPC-E1, EAN-8, EAN-13 B Code 39, Code 32 C Codabar D Code 128, ISBT 128, ISBT 128 Concatenated E Code 93 F Interleaved 2 of 5 G Discrete 2 of 5, or Discrete 2 of 5 IATA H Code 11 J MSI K GS1-128 L Bookland EAN M Trioptic Code 39 N Coupon Code R GS1 DataBar Family T UCC Composite, TLC 39 U Chinese 2 of 5 X ISSN EAN, PDF417, Macro PDF417, Micro
B-2 MP6000 BAR CODE PROGRAMMING GUIDE Table B-1 Symbol Code Characters (Continued) Code Character Code Type z Aztec, Aztec Rune P00 Data Matrix P01 QR Code, MicroQR P0X Signature Capture
PROGRAMMING REFERENCE AIM Code Identifiers Each AIM Code Identifier contains the three-character string ]cm where: ] = Flag Character (ASCII 93) c = Code Character (see Table B-2) m = Modifier Character (see Table B-3) Table B-2 Aim Code Characters Code Character Code Type A Code 39, Code 39 Full ASCII, Code 32 C Code 128, ISBT 128, ISBT 128 Concatenated, GS1-128, Coupon (Code 128 portion) d Data Matrix E UPC/EAN, Coupon (UPC portion) e GS1 DataBar Family F Codabar G Code 93 H Code 11 I
B-4 MP6000 BAR CODE PROGRAMMING GUIDE The modifier character is the sum of the applicable option values based on Table B-3. Table B-3 Modifier Characters Code Type Code 39 Option Value Option 0 No check character or Full ASCII processing. 1 Reader has checked one check character. 3 Reader has checked and stripped check character. 4 Reader has performed Full ASCII character conversion. 5 Reader has performed Full ASCII character conversion and checked one check character.
PROGRAMMING REFERENCE B-5 Table B-3 Modifier Characters (Continued) Code Type D 2 of 5 Option Value 0 Option No options specified at this time. Always transmit 0. Example: A D 2 of 5 bar code 4123, is transmitted as ]S04123 UPC/EAN 0 Standard data packet in full EAN format, i.e. 13 digits for UPC-A, UPC-E, and EAN-13 (not including supplemental data). 1 Two digit supplemental data only. 2 Five digit supplemental data only.
B-6 MP6000 BAR CODE PROGRAMMING GUIDE Table B-3 Modifier Characters (Continued) Code Type PDF417, Micro PDF417 Option Value Option 0 Reader set to conform to protocol defined in 1994 PDF417 symbology specifications. Note: When this option is transmitted, the receiver cannot reliably determine whether ECIs have been invoked or whether data byte 92DEC has been doubled in transmission. 1 Reader set to follow the ECI protocol (Extended Channel Interpretation). All data characters 92DEC are doubled.
PROGRAMMING REFERENCE B-7 Table B-3 Modifier Characters (Continued) Code Type QR Code Aztec Option Value Option 0 Model 1 symbol. 1 Model 2 / MicroQR symbol, ECI protocol not implemented. 2 Model 2 symbol, ECI protocol implemented. 3 Model 2 symbol, ECI protocol not implemented, FNC1 implied in first position. 4 Model 2 symbol, ECI protocol implemented, FNC1 implied in first position. 5 Model 2 symbol, ECI protocol not implemented, FNC1 implied in second position.
B-8 MP6000 BAR CODE PROGRAMMING GUIDE
APPENDIX C SAMPLE BAR CODES Code 39 c 123ABC
C-2 MP6000 BAR CODE PROGRAMMING GUIDE UPC/EAN UPC-A, 100% 0 12345 67890 5
SAMPLE BAR CODES UPC/EAN (continued) EAN-13, 100% 3 456789 012340 C-3
C-4 MP6000 BAR CODE PROGRAMMING GUIDE Code 128 1234567890
SAMPLE BAR CODES Interleaved 2 of 5 12345678901231 C-5
C-6 MP6000 BAR CODE PROGRAMMING GUIDE GS1 DataBar-14 NOTE DataBar-14 must be enabled to read the bar code below (see GS1 DataBar on page 11-203).
SAMPLE BAR CODES PDF417 12345678910abcdefghijklmnopqrstuvwxyz C-7
C-8 MP6000 BAR CODE PROGRAMMING GUIDE Data Matrix 123456789abcdefghijklmnopqrstuvwxyz
SAMPLE BAR CODES C-9 QR Code 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789
C - 10 MP6000 BAR CODE PROGRAMMING GUIDE
APPENDIX D NUMERIC BAR CODES Numeric Bar Codes For parameters requiring specific numeric values, scan the appropriately numbered bar code(s).
D-2 MP6000 BAR CODE PROGRAMMING GUIDE 1 1
NUMERIC BAR CODES 2 2 D-3
D-4 MP6000 BAR CODE PROGRAMMING GUIDE 3 3
NUMERIC BAR CODES 4 4 D-5
D-6 MP6000 BAR CODE PROGRAMMING GUIDE 5 5
NUMERIC BAR CODES 6 6 D-7
D-8 MP6000 BAR CODE PROGRAMMING GUIDE 7 7
NUMERIC BAR CODES 8 8 D-9
D - 10 MP6000 BAR CODE PROGRAMMING GUIDE 9 9
NUMERIC BAR CODES D - 11 Cancel To correct an error or change a selection, scan the bar code below.
D - 12 MP6000 BAR CODE PROGRAMMING GUIDE
APPENDIX E ASCII CHARACTER SETS Character Sets You can assign the values in Table E-1 as prefixes or suffixes for ASCII character data transmission. This table does not apply to USB.
E-2 MP6000 BAR CODE PROGRAMMING GUIDE Table E-1 Character Sets (Continued) Full ASCII Code 39 Encode Character Prefix/Suffix Value ASCII Character 1016 $P DLE 1017 $Q DC1/XON 1018 $R DC2 1019 $S DC3/XOFF 1020 $T DC4 1021 $U NAK 1022 $V SYN 1023 $W ETB 1024 $X CAN 1025 $Y EM 1026 $Z SUB 1027 %A ESC 1028 %B FS 1029 %C GS 1030 %D RS 1031 %E US 1032 Space Space 1033 /A ! 1034 /B 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G 1040 /H
SAMPLE BAR CODES Table E-1 Character Sets (Continued) Full ASCII Code 39 Encode Character Prefix/Suffix Value ASCII Character 1047 /O / 1048 0 0 1049 1 1 1050 2 2 1051 3 3 1052 4 4 1053 5 5 1054 6 6 1055 7 7 1056 8 8 1057 9 9 1058 /Z : 1059 %F ; 1060 %G < 1061 %H = 1062 %I > 1063 %J ? 1064 %V @ 1065 A A 1066 B B 1067 C C 1068 D D 1069 E E 1070 F F 1071 G G 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M E
E-4 MP6000 BAR CODE PROGRAMMING GUIDE Table E-1 Character Sets (Continued) Full ASCII Code 39 Encode Character Prefix/Suffix Value ASCII Character 1078 N N 1079 O O 1080 P P 1081 Q Q 1082 R R 1083 S S 1084 T T 1085 U U 1086 V V 1087 W W 1088 X X 1089 Y Y 1090 Z Z 1091 %K [ 1092 %L \ 1093 %M ] 1094 %N ^ 1095 %O _ 1096 %W 1097 +A a 1098 +B b 1099 +C c 1100 +D d 1101 +E e 1102 +F f 1103 +G g 1104 +H h 1105 +I i 1106 +J j
SAMPLE BAR CODES Table E-1 Character Sets (Continued) Full ASCII Code 39 Encode Character Prefix/Suffix Value ASCII Character 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S s 1116 +T t 1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1127 (RS-232 only) Undefined 7013 (RS-232 only) ENTER E-5
E-6 MP6000 BAR CODE PROGRAMMING GUIDE
INDEX Numerics 123Scan2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 2D bar codes aztec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-251 aztec inverse . . . . . . . . . . . . . . . . . . . . . . . . 11-253 code 128 emulation . . . . . . . . . . . . . . . . . . . 11-233 data matrix . . . . . . . . . . . . . . . . . . . . . . . . . . 11-235 data matrix GS1 . . . . . . . . . . . . . . . . . . . . . . 11-240 data matrix inverse . . . . . . . . . . . . . . . . . . . .
Index - 2 MP6000 BAR CODE PROGRAMMING GUIDE code 39 full ASCII . . . . . . . . . . . . . . . . . . . . . 11-115 code 39 lengths . . . . . . . . . . . . . . . . . . . . . . . 11-107 code 39 marginless mode . . . . . . . . . . . . . . . 11-124 code 39 stitching . . . . . . . . . . . . . . . . . . . . . . 11-117 code 39 stitching security level . . . . . . . . . . . 11-119 code 39 transmit check digit . . . . . . . . . . . . . 11-113 code 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX - 3 pid type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74 prefix/suffix values . . . . . . . . . . . . . . . . . . . . . . 5-82 presentation frame timeout . . . . . . . . . . . . . . . . 5-34 QR code . . . . . . . . . . . . . . . . . . . . . . 11-242, 11-247 QR inverse . . . . . . . . . . . . . . . . . . . . . . . . . . 11-244 RS-232 baud rate . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18 beep on bel . . . . . . . . . . . . . . . . . . . . . . . .
Index - 4 MP6000 BAR CODE PROGRAMMING GUIDE GS1-128 . . . . . . . . . . . . . . . . . . . . . . . .11-80, 11-81 ISBT 128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-82 ISBT concatenation . . . . . . . . . . . . . . . .11-84, 11-87 ISBT concatenation redundancy . . . . . . . . . . . 11-89 lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-75 marginless mode . . . . . . . . . . . . . . . . . . . . . . . 11-97 stitching . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX - 5 P parser version ID . . . . . . . . . . . . . . . . . . . . . . . . . . 12-90 parsing driver’s license data . . . . . . . . . . . . . . . . . . . . . 12-1 PDF417 bar codes . . . . . . . . . . . . . . . . . . . . . . . 11-229 PDF prioritization . . . . . . . . . . . . . . . . . . . . . . . 5-40 plural stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv product id type . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74 Q QR code bar codes . . . . . . . . . . . . .
Index - 6 MP6000 BAR CODE PROGRAMMING GUIDE
Zebra Technologies Corporation Lincolnshire, IL U.S.A. http://www.zebra.com Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company. © 2014 Symbol Technologies, Inc.
