MC75 Enterprise Digital Assistant User Guide
MC75 Enterprise Digital Assistant User Guide 72E-103077-02 Rev.
ii MC75 User Guide © 2008 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change Date Description -01 Rev. A 6/10/08 Initial release. -02 Rev. A 08/14/08 Add re-boot after installing SIM card. Add dual line SIM support.
iv MC75 User Guide
Table of Contents Patents.................................................................................................................................................. ii Revision History.................................................................................................................................... iii About This Guide Introduction ...........................................................................................................................................
vi MC75 User Guide Chapter 2: Using the MC75 Introduction .......................................................................................................................................... Today Screen ...................................................................................................................................... Status Icons ......................................................................................................................................... Programs .....
Table of Contents Enabling Bluetooth ......................................................................................................................... Bluetooth Power States ................................................................................................................. Cold Boot ................................................................................................................................. Warm Boot .................................................................
viii MC75 User Guide Chapter 5: Using the Phone Introduction .......................................................................................................................................... Accessing the Phone Keypad .............................................................................................................. Turning the Phone On and Off ............................................................................................................. Using a Wired Headset ...........
Table of Contents ix Charging Temperature ............................................................................................................. Charging ........................................................................................................................................ Battery Charging Indicators ........................................................................................................... Charging Temperature .......................................................
x MC75 User Guide Appendix A: Technical Specifications MC75 Technical Specifications ............................................................................................................ MC75 ............................................................................................................................................. Single Slot USB/Serial Cradle ........................................................................................................ Four Slot Ethernet Cradle ........
About This Guide Introduction This guide provides information about using the MC75 Enterprise Digital Assistant (EDA) and accessories. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens. Documentation Set The documentation set for the MC75 provides information for specific user needs, and includes: • MC75 Quick Start Guide - describes how to get the MC75 EDA up and running. • MC75 User Guide - describes how to use the MC75 EDA.
xii MC75 User Guide Configurations This guide covers the following configurations: Configuration Radios Display Memory Data Capture Operating System Keypads MC7506 WPAN: Bluetooth WWAN: HSDPA GPS: SiRF III 3.5” VGA Color 128 MB RAM/ 256 MB Flash 1D laser scanner, 2D imager or camera Windows Mobile 6 Professional Numeric or Alphanumeric keypad MC7508 WPAN: Bluetooth WWAN: EVDO GPS: SiRF III 3.
About This Guide The second line lists the operating system version and the build number. The last part of the build number represents the AKU number. For example, Build 18552.0.7.5 indicates that the device is running AKU version 0.7.5. OEM Version To determine the OEM software version: Tap Start > Settings > System tab > System Info icon > System tab. BTExplorer Software To determine the BTExplorer software version: Tap BTExplorer icon > Show BTExplorer> Menu > About.
xiv MC75 User Guide Fusion Software To determine the Fusion software version: Tap Signal Strength icon > Wireless Status > Versions. Signal Strength icon Phone Software To determine the Phone software version: Tap Start > Phone > Menu > Options > Phone Info or Version Information tab.
About This Guide MC7506/96 MC7508/98 Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started provides information on getting the MC75 up and running for the first time. • Chapter 2, Using the MC75 provides basic instructions for using the MC75, including powering on and resetting the MC75, and entering and capturing data. • Chapter 3, Using GPS Navigation provides information about GPS navigation with the MC75.
xvi MC75 User Guide • Bold text is used to highlight the following: • Dialog box, window, and screen names • Drop-down list and list box names • Check box and radio button names • Key names on a keypad • Button names on a screen. • bullets (•) indicate: • Action items • Lists of alternatives • Lists of required steps that are not necessarily sequential • Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
About This Guide xvii If you purchased your Enterprise Mobility business product from a Motorola business partner, contact that business partner for support.
xviii MC75 User Guide
Chapter 1 Getting Started Introduction This chapter lists the parts and accessories for the MC75 and explains how to install and charge the batteries, replace the strap, and power on the MC75 for the first time.
1-2 MC75 User Guide Battery Cover Handstrap Handstrap Slot Battery Cover Latch Headset Jack Camera Flash IrDA Window Camera Memory Card Cover Speaker Action Button Scan Window (Imager Configuration Shown) Scan/Action Button Stylus Tether Point Figure 1-2 MC75 Rear View Unpacking Carefully remove all protective material from the MC75 and save the shipping container for later storage and shipping.
Getting Started 1-3 Accessories Table 1-1 lists the accessories available for the MC75. Table 1-1 MC75 Accessories Accessory Part Number Description Cradles Single Slot USB/Serial Cradle CRD7X00-1000RR Charges the MC75 main battery and a spare battery. Synchronizes the MC75 with a host computer through a USB connection. Four Slot Ethernet Cradle CRD7000-4000ER Charges the MC75 main battery and connects the MC75 with an Ethernet network.
1-4 MC75 User Guide Table 1-1 MC75 Accessories (Continued) Accessory Part Number Description Battery Kit for 3600 mAh battery BTRY-KT-1R5X-MC7XR Replacement 3600 mAh battery and battery door. Battery Kit for 4800 mAh battery BTRY-KT-2R5X-MC7XR Replacement 4800 mAh battery and battery door. Headset 50-11300-050R Use in noisy environments. Belt Mounted Rigid Holster SG-MC70011110-01R Clips onto belt to hold the MC75 when not in use.
Getting Started 1. 1-5 Lift the SIM cover using the stylus tip. Figure 1-3 Lifting the SIM Cover 2. Insert the SIM card, as shown in Figure 1-4, with the cut edge of the card facing out and the contacts facing down. Figure 1-4 Inserting the SIM Card 3. Lower the SIM cover and using the stylus tip, slide it in place. 4. Install the battery. See Installing the Main Battery on page 1-6 for more information. 5. After completing initial MC75 setup or after replacing a SIM card: a.
1-6 MC75 User Guide Installing the Main Battery NOTE The MC75 ships with a 3600 mAh battery. An optional 4800 mAh battery is available. To install the main battery: 1. Insert the battery, top first, into the battery compartment in the back of the MC75. NOTE 2. Position the battery correctly, with the battery charging contacts on top of the charging contacts in the battery compartment. Press the battery down into the battery compartment until the battery release latch snaps into place.
Getting Started 1-7 Charging the Battery CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 7-2. Charging the Main Battery and Memory Backup Battery Before using the MC75 for the first time, charge the main battery until the amber Charging/Battery Status LED remains lit (see Table 1-2 on page 1-7 for charge status indications). To charge the MC75, use a cable or a cradle with the appropriate power supply.
1-8 MC75 User Guide Table 1-2 LED Charge Indicators (Continued) Charging/Battery Status LED Indication Single Blink Amber (when Power button pressed) Battery depleted. Blinking Amber (when Power button pressed) Battery over-temperature condition. Charging Spare Batteries See Chapter 6, Accessories for information on using accessories to change spare batteries. Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75.
Getting Started 1-9 Micro Secure Digital (microSD) Card The microSD card slot provides secondary non-volatile storage. The slot is located on the side of the MC75 (see Figure 1-7). Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use. CAUTION Follow proper ESD precautions to avoid damaging the microSD card.
1 - 10 MC75 User Guide Adjusting the Handstrap The MC75 handstrap is attached to the bottom of the battery cover. Adjust the handstrap to increase comfort when holding the MC75 for extended periods of time. To adjust the handstrap: 1. Feed the handstrap through the handstrap slot in either direction, to tighten or loosen. 2. Secure the handstrap by pressing the two sides together as shown in Figure 1-9.
Getting Started 1 - 11 NOTE Not using a screen protector can affect warranty coverage. To purchase replacement protectors, contact your local account manager or Motorola, Inc. These include screen protector installation instructions. Part number: KT-67525-01R Screen Protector 3/pk. Replacing the Main Battery 1. Press the red Power button to suspend the MC75. 2. Loosen the handstrap. 3. Open the battery cover latches on either side of the battery cover.
1 - 12 MC75 User Guide Battery Management Observe the following battery saving tips: NOTE The MC75 factory default settings for the WWAN and WLAN radios are set to ON. • Leave the MC75 connected to AC power at all times when not in use. • Set the MC75 to turn off after a short period of non-use. • Set the backlight to turn off after a short period of non-use. • Turn off all wireless activities when not in use. • Power off the MC75 when charging to charge at a faster rate.
Getting Started 1 - 13 Turning Off the Radios Windows Mobile 6 devices include Wireless Manager, which provides a simple method of enabling, disabling, and configuring all the device’s wireless capabilities in one place. To open Wireless Manager, tap the Connectivity icon or tap Wireless Manager on the Today screen. Connectivity icon Figure 1-12 Opening Wireless Manager Select Wireless Manager. Figure 1-13 Wireless Manager Window NOTE Wireless connection options vary depending upon configurations.
1 - 14 MC75 User Guide Figure 1-14 Wireless Manager Menu
Chapter 2 Using the MC75 Introduction This chapter explains the buttons, status icons, and controls on the MC75, and provides basic instructions for using the MC75, including powering on and resetting the MC75, and entering and capturing data. The MC75 factory default radio states are: • Bluetooth - OFF • Phone - ON • Wireless LAN - ON. Today Screen The Today screen displays important information, such as upcoming appointments and status indicators.
2-2 MC75 User Guide To customize the Today screen, tap Start > Settings > Today icon. Use the Appearance tab to customize the background and the Items tab to change the list and order of items that appear on the screen. Status Icons The Navigation bar at the top of the screen can contain the status icons listed in Table 2-1. Table 2-1 Status Icons Icon Function Notification Description Backup Battery Low. Notification that one or more instant messages were received.
Using the MC75 Table 2-1 Status Icons (Continued) Icon Function WAN Description Call missed. Dialing while no SIM card is installed. Voice call in progress. Calls are forwarded. Call on hold. Speakerphone is on. Antenna/signal icon: wireless on/good signal. Antenna/signal icon: wireless off. Antenna/signal icon: no service or searching. HSDPA connecting. (MC7506 and MC7596) HSDPA in use. (MC7506 and MC7596) 3G connecting. (MC7506 and MC7596) 3G in use. (MC7506 and MC7596) GPRS connecting.
2-4 MC75 User Guide The command bar at the bottom of the screen can contain the task tray icons listed in Table 2-2. Table 2-2 Task Tray Icons Icon Description Wireless connection status Indicates WLAN signal strength. Bluetooth Enabled Bluetooth radio is on. Bluetooth Disabled Bluetooth radio is off. Bluetooth Connection Bluetooth radio is connected to another Bluetooth device. ActiveSync Active serial connection between the MC75 and the host computer.
Using the MC75 2-5 Table 2-3 Programs in the Start Menu Icon Name Description Messaging Send and receive e-mail, MMS, and text messages. Phone Make and receive calls, switch between calls, and set up conference calling. Help See Help topics for the current screen or program. Table 2-4 lists programs that are listed in the Programs window. Table 2-4 Programs in Program Window Icon Name Description ActiveSync Synchronize information between the MC75 and a host computer or the Exchange Server.
2-6 MC75 User Guide Table 2-4 Programs in Program Window (Continued) Icon Name Description Notes Create handwritten or typed notes, drawings, and voice recordings. Pictures & Videos View and manage pictures, animated GIFs, and video files. Rapid Deployment Facilitates software downloads from a Mobility Services Platform Console FTP server to the MC75. Refer to the MC75 Integrator Guide for more information.
Using the MC75 2-7 Settings Table 2-5 lists control applications pre installed on the MC75. Tap Start > Settings to open the Settings window. Table 2-5 Settings in the Setting Window Icon Name Description Personal Tab Buttons Assign a program to a button. Input Set options for each of the input methods. Lock Set a password for the MC75. Menus Set what programs appear in the Start menu. Owner Information Enter personal information on the MC75.
2-8 MC75 User Guide Table 2-5 Settings in the Setting Window (Continued) Icon Name Description Customer Feedback Submit feedback on the Windows Mobile 6 software. Encryption Allow files on a storage card to be encrypted. Encrypted files are readable only on your device. Error Reporting Enable or disable the device's error reporting function.
Using the MC75 2-9 Table 2-5 Settings in the Setting Window (Continued) Icon Name Description Connections Tab Beam Set the MC75 to receive incoming IrDA beams. Connections Set up one or more types of modem connections for your device, such as phone dial-up, GPRS, Bluetooth, and more, so that your device can connect to the Internet or a private local network. USB to PC Enables or disables the enhanced network connectivity. Wi-Fi Setup wireless network connection and customize settings.
2 - 10 MC75 User Guide Adjusting Volume To adjust the system volume using the Speaker icon in the navigation bar: 1. Tap the Speaker icon. The Volume dialog box appears. Figure 2-2 Volume Dialog Box 2. Tap and move the slide bar to adjust the volume. 3. Select the On or Off radio button to turn the volume on or off. You can also adjust the system volume using the Sounds & Notifications window, or use the Up/Down button on the side of the MC75.
Using the MC75 2 - 11 Figure 2-4 Battery Icon on the Title Bar Also view the battery status using the Power window. Battery Reserve Options If the charge of the battery reaches a critical threshold, the MC75 shuts down. This threshold can be changed but affects the amount of time that data can be retained. 1. Tap Start > Settings > Power icon > RunTime tab. A warning message appears. Figure 2-5 Warning Message 2. Read the warning message and tap ok. Figure 2-6 RunTime Tab 3.
2 - 12 MC75 User Guide Main Battery Temperature Notifications The temperature notification system implements three levels of notification when the temperature within the battery exceeds specific temperature thresholds: • Level 1: Temperature Watch; this level is similar to main battery low warning. It indicates that the battery temperature has reached the first threshold level. The user should move to an environment within proper operating temperature.
Using the MC75 2 - 13 LED Indicators The MC75 has three LED indicators. The Scan/Decode LED indicates status for bar code scanning. The Charging/Battery Status LED indicates battery charging and status. The Radio Status LED indicates WAN radio status. Table 2-6 describes the LED indications. Scan/Decode Charging/Battery Radio Status Status LED LED LED Figure 2-9 LED Indicators Table 2-6 LED Indications LED State Indication Scan/Decode LED Solid Green Successful decode/capture.
2 - 14 MC75 User Guide Resetting the MC75 There are two reset functions, warm boot and cold boot. A warm boot restarts the MC75 by closing all running programs. A cold boot also restarts the MC75, and also resets the clock. Data saved in flash memory or a memory card is not lost. If the MC75 is not functioning properly, perform a warm boot first. If the MC75 still does not respond, perform a cold boot. Performing a Warm Boot Hold down the Power button for approximately five seconds.
Using the MC75 2 - 15 Locking the MC75 Use the Device Lock feature to prevent use of the device. Note that when locked, the MC75 does not respond to screen or keypad input. To lock the device, tap the Device unlocked icon. The icon changes to locked. Device Unlocked Icon Device Locked Icon Figure 2-10 Device Locked/Unlocked Icons To unlock the device and free it for use, tap Unlock. Figure 2-11 Unlock Device Window Tap Unlock on the Unlock window.
2 - 16 MC75 User Guide Keypads The MC75 offers two types modular keypad configurations: Numeric and alpha-numeric. Numeric Keypad Configuration The numeric keypad contains application keys, scroll keys, and function keys. The keypad is color-coded to indicate the alternate function key (blue) values. Note that an application can change keypad functions so the MC75’s keypad may not function exactly as described.
Using the MC75 2 - 17 Table 2-8 MC75 Numeric Keypad Descriptions (Continued) Key Description Talk/End Talk (Green Phone): press to display the phone keypad window or to dial a phone number (from the phone keypad window). End (Red Phone): press when the phone keypad window displays to stop dialing or end a call. Scan (yellow) Activates the scanner/imager in a scan enabled application. Scroll Up and Down Moves up one item. Moves left one item when pressed with the Orange key.
2 - 18 MC75 User Guide Table 2-8 MC75 Numeric Keypad Descriptions (Continued) Key Description SHIFT Press and release the SHIFT key to activate the keypad alternate SHIFT functions. A single press displays the following icon at the bottom of the screen, until a second key is pressed: Press the Orange key, then the Shift key to add a temporary shift (that applies only to the next key pressed) to the orange lock state.
Using the MC75 2 - 19 Table 2-9 Numeric Keypad Input Modes (Continued) Orange Key (Alpha Lowercase Mode) Numeric Mode Orange + Shift Keys (Alpha Uppercase Mode) Key Blue+ Key SHIFT + Key 1st Press 2nd Press 3rd Press 4th Press 1st Press Up Up Up Hilight Up Left Left Down Down Down Hilight Down Right Right Enter Action Action Action Action Action 2nd Press 3rd Press 4th Press Note: An application can change the key functions. The keypad may not function exactly as described.
2 - 20 MC75 User Guide Figure 2-15 QWERTZ Keypad Configuration Table 2-10 Alpha-numeric Keypad Descriptions Key Blue Key Action Launches applications (shown on the keypad in blue). Press the Blue key once to activate this mode temporarily, followed by another key. This displays the following icon at the bottom of the screen, until a second key is pressed: Press the Blue key twice to lock this mode. This displays the following icon at the bottom of the screen: Press the Blue key a third time to unlock.
Using the MC75 2 - 21 Table 2-10 Alpha-numeric Keypad Descriptions (Continued) Key Action Scroll Up and Left Moves up one item. Moves left one item when pressed with the Orange key. Scroll Down and Right Moves down one item. Moves right one item when pressed with the Orange key. Soft Keys Accesses the command or menu above it on the screen. Shift Changes the state of the alpha characters from lowercase to uppercase.
2 - 22 MC75 User Guide Table 2-10 Alpha-numeric Keypad Descriptions (Continued) Key Action Menu Use this key in conjunction with the Blue key to instantly display the context menu from any application without tapping the screen. This function is user programmable. Phonepad Use this key in conjunction with the Blue key to display the Phonepad application without tapping the screen. This function is user programmable.
Using the MC75 2 - 23 Table 2-11 QWERTY Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key X x X 8 C c C 9 V v V % B b B & N n N ! M m M ? , , < @ ENTER Enter Backlight Backlight Backlight 0 Backlight TAB Tab Tab Back tab Tab SPACE Space Space Space Space Star * * * * . . > . . Note: An application can change the key functions. The keypad may not function exactly as described.
2 - 24 MC75 User Guide Table 2-12 AZERTY Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key F f F 6 G g G ( H h H ) J j J / K k K : L l L ‘ M m M ? Shift Shift W w W 7 X x X 8 C c C 9 V v V % B b B & N n N ! , , < @ Backspace backspace Enter Enter Backlight Backlight Backlight 0 Backlight TAB Tab Tab Back tab Tab SPACE Space Space Space Space Star * * * * . . > . .
Using the MC75 2 - 25 Table 2-13 QWERTZ Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key T t T + Z z Z _ U u U - I i I = O o O “ P p P áü A a A # S s S 4 D d D 5 F f F 6 G g G ( H h H ) J j J / K k K : L l L ‘ Backspace Backspace Shift Shift Y y Y 7 X x X 8 C c C 9 V v V % B b B & N n N ! M m M ? , , < @ ENTER Enter Backlight Backlight Backlight 0 Backlight TAB Tab Tab
2 - 26 MC75 User Guide Table 2-13 QWERTZ Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key SPACE Space Space Space Space Star * * * * . . > . . Note: An application can change the key functions. The keypad may not function exactly as described. Special Character Key NOTE Special characters are only available on the alpha-numeric keypad configurations.
Using the MC75 2 - 27 Table 2-14 Special Characters (Continued) Key Special Characters Key ! . * @ % , # & _ ‘ ? : Special Characters - Function Buttons The MC75’s buttons perform certain functions. Scan/Action Button Power Button Up/Down Button Action Button Scan/Action Button Figure 2-16 Function Buttons • Power: Press the red Power button to turn the MC75 screen on and off. The MC75 is in suspend mode when the screen is off.
2 - 28 MC75 User Guide Stylus Use the MC75 stylus to select items and enter information. The stylus functions as a mouse. • Tap: Touch the screen once with the stylus to press option buttons and open menu items. • Tap and Hold: Tap and hold the stylus on an item to see a list of actions available for that item. On the pop-up menu that appears, tap the action to perform. • Drag: Hold the stylus on the screen and drag across the screen to select text and images. Drag in a list to select multiple items.
Using the MC75 2 - 29 Data Capture The MC75 offers three types of data capture options: • Linear scanning • Imaging • Digital camera. NOTE To perform data capture a scanning enabled application must be installed on the MC75. A sample scanning application can be downloaded from the Motorola Support site at http://support.symbol.com.
2 - 30 MC75 User Guide Digital Camera MC75 with an integrated digital camera have the following features: • Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, PDF417, and 2D matrix code types. • Advanced intuitive aiming for easy point-and-shoot operation.
Using the MC75 2 - 31 Figure 2-18 Linear Scanning 3. Press the scan button. Ensure the red scan beam covers the entire bar code. The Scan/Decode LED lights red to indicate that scanning is in process, then lights green and a beep sounds, by default, to indicate the bar code was decoded successfully. Correct Incorrect Figure 2-19 Linear Scanner Aiming Pattern Imager Scanning 1. Ensure that a scan-enabled application is loaded on the MC75. 2. Aim the scan window at the bar code.
2 - 32 MC75 User Guide Linear bar code PDF417 symbol Symbol View Finder (Aiming Pattern) Correct Figure 2-21 Imager Aiming Pattern: Bar Code Centered Incorrect Correct Figure 2-22 Imager Aiming Pattern: Bar Code Not Centered Figure 2-23 Pick List Mode with Multiple Bar Codes in Aiming Pattern 4. Release the scan button. NOTE Imager decoding usually occurs instantaneously.
Using the MC75 2 - 33 Figure 2-24 Sample Scan Application with Preview Window 4. Move the MC75 until the red aiming reticle is on the bar code to scan. The aiming reticle turns green when the MC75 is able to decode the bar code. Figure 2-25 Digital Camera Scanning 5. Release the scan button. The Scan/Decode LED lights green and a beep sounds, by default, to indicate the bar code was decoded successfully. Taking Photos To take a photo: 1. Tap Start > Programs > Pictures & Videos icon. 2.
2 - 34 MC75 User Guide Recording Video To record a video clip: 1. Tap Start > Programs > Pictures & Videos icon. 2. Tap Camera on the command bar. 3. Tap Menu > Video to set shooting mode to video. The available recording time displays on the screen. NOTE 4. By default, the time limit for recording videos is set to 30 seconds. Press the Enter key to begin recording. Recording stops when you press the Enter button again.
Using the MC75 2 - 35 Figure 2-26 Beam Window 3. Tap ok. Infrared Connection Using infrared, you can enable short-range file exchange between your MC75 and another IrDA device. Exchanging Files using IR Connection Ensure that the IrDA function on both the MC75 and the other device are enabled. To send files via IrDA connection: 1. Switch to the program where you created the item you want to send and locate the item in the list. NOTE 2. Do not cover or block the IrDA window.
2 - 36 MC75 User Guide Figure 2-28 Beam Contact To receive files via IrDA connection: 1. Align the IrDA port of the MC75 with that of the other IrDA device so that they are unobstructed and within a close range. 2. On the other device, send the file to the MC75. Figure 2-29 Receive File 3. When the Receiving Data dialog displays, tap Yes.
Chapter 3 Using GPS Navigation Introduction The MC75 includes Global Positioning System (GPS) technology using the SiRF III chipset. GPS technology is based on a worldwide system of GPS satellites orbiting the earth that continuously transmit digital radio signals. These radio signals contain data on the satellites’ locations and their exact clock time and are used to determine your location on the earth.
3-2 MC75 User Guide 4. Select 57600 from the Baud rate drop-down list. 5. Tap ok to close the Setting window. NOTE If an application error message appears indicating that the COM port cannot be opened, ensure that a free COM port is selected in the GPS hardware port drop-down list. Operation Acquiring satellite signals may take a few minutes. It is best to be outside and have a clear, unobstructed view of the sky.
Using GPS Navigation 3-3 improves the performance of the Time To First Fix (TTFF) of GPS receivers by providing them with data that they would ordinarily have to download from the GPS satellites. With the A-GPS data, GPS receivers can operate faster and more reliably. A-GPS follows the Secure User Plane Location (SUPL) protocol which allows the MC75 to communicate with a location server. Refer to the EMDK Help file for information on setting up SUPL on the MC75.
3-4 MC75 User Guide
Chapter 4 Using Bluetooth Introduction Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1). Bluetooth wireless technology is specifically designed for short-range (30 feet/10 meters) communication and low power consumption. MC75s with Bluetooth capabilities can exchange information (e.g.
4-2 MC75 User Guide The Bluetooth radio in this MC75 operates as a Class 2 device power class. The maximum output power is 2.5mW and the expected range is 32.8 feet (10 meters). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether one measures open space or closed office space. NOTE It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
Using Bluetooth 4-3 Turning the Bluetooth Radio Mode On and Off Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (e.g., an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the MC75. Turn on the Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with Bluetooth radios in close proximity. NOTE To achieve the best battery life turn off radios not in use.
4-4 MC75 User Guide Bluetooth Power States Cold Boot Performing a cold boot on the MC75 turns off Bluetooth after initialization (which takes a few moments). It is normal to see the Bluetooth icon appear and disappear, as well as a wait cursor, when initialization proceeds in all modes. Warm Boot Performing a warm boot on the MC75 returns Bluetooth to the last state after initialization. Suspend Suspending the MC75 turns off Bluetooth.
Using Bluetooth 4-5 Figure 4-3 Explorer Mode Window You can also use the “tap and hold” technique to view available options. Scroll bars and view options are similar to those on the Windows desktop.
4-6 MC75 User Guide Discovering Bluetooth Device(s) The MC75 can receive information from discovered devices without bonding. However, once bonded, the MC75 and a bonded device exchange information automatically when you turn the Bluetooth radio on. See Bonding with Discovered Device(s) on page 4-20 for more information. To find Bluetooth devices in the area: 1. Ensure that Bluetooth is enabled on both devices. 2. Ensure that the Bluetooth device to discover is in discoverable and connectable modes.
Using Bluetooth 4-7 • Send or Exchange Objects • Associate Serial Port. NOTE 8. If a device discovery action has not been previously performed, a device discovery is automatically initiated. If a device discovery has previously been performed, the device discovery process is skipped, and the previously found list of devices displays. To start a new device discovery, tap and hold in the window and select Discover Devices from the pop-up menu. BTExplorer searches for Bluetooth devices in the area.
4-8 MC75 User Guide Figure 4-7 Device Services NOTE If the MC75 discovers a service but the service is not supported, the service icon is grayed-out. 10. Select a service from the list and press Next. The Connection Favorite Options window appears. Figure 4-8 Connection Favorite Options Window 11. In the Favorite Name text box, enter a name for this service that will appear in the Favorite window. 12. Tap Next. The Connection Summary window appears. 13.
Using Bluetooth 4-9 Figure 4-9 Favorites Window Available Services NOTE Some devices might not require a PIN. This depends upon the device’s authentication. The MC75 offers the following services: • File Transfer Services • Dial-Up Networking Services • OBEX Object Push Services • Headset Audio Gateway Services • Hands-Free Audio Gateway Services • Serial Port Services • Personal Area Networking Services • IrMC Services. See the following sections for information on these services.
4 - 10 MC75 User Guide 4. Select the device and tap Next. The Select Remote Service window appears. 5. Tap Next. The Connection Favorite Options window appears. 6. Tap Next. The Connection Summary window appears. 7. Tap Connect. The remote device’s accessible folders appear. Figure 4-10 File Transfer Window 8. Double-tap the file to copy. The Save Remote File window appears. Figure 4-11 Save Remote File Window 9. Tap and hold on the file. A pop-up menu appears. 10.
Using Bluetooth 4 - 11 2. Enter the name for the new folder or file. 3. Tap OK to create the new folder or file on the remote device. Deleting a File To delete a file from the remote device: 1. Tap and hold on the file to delete and select Delete. 2. In the Delete Remote Device File dialog box tap Yes. Getting a File To copy a file from a remote device: 1. Double-tap or tap and hold on the file and select Get. The Save Remote File window appears. 2. Navigate to the directory to save the file.
4 - 12 MC75 User Guide Dial-Up Networking Services Dial-up networking allows the user to connect a PC or laptop to the MC75 and use the MC75 as a modem to connect to an office network or ISP. Before setting up dial-up networking, obtain dial-up information and other necessary settings (username, password and domain name, if required) for the office network or ISP. To create a new Bluetooth connection: 1. Ensure the MC75 is discoverable and connectable. See Device Info Tab on page 4-23. 2.
Using Bluetooth 4 - 13 2. Ensure that the OBEX Object Push profile is enabled on the MC75. See Profiles Tab on page 4-32 for more information. NOTE If favorite connections have already been created, the Favorites screen displays. If no favorite connections have been created, the New Connection Wizard screen displays. 3. Use the Connection Wizard to search for a Bluetooth device. 4. Select the device and tap Next. 5. Select the OBEX Object Push service and select Connect.
4 - 14 MC75 User Guide Figure 4-14 Select Contact Entry Window 4. Select a contact to send to the other device. 5. Tap OK. 6. Tap OK to send the contact to the other device and display a confirmation dialog box on the other device to accept the contact. A Send Contact dialog appears. 7. Tap Ok. Swapping Contacts To swap contacts with another device: NOTE 1. Prior to swapping contacts, a default contact must be set up before attempting to send a contact.
Using Bluetooth 4 - 15 Figure 4-16 Select Contact Entry Window 4. Select a contact to send to the other device. 5. Tap OK. 6. Tap OK to swap contacts with the other device and display a confirmation dialog box on the other device to accept the contact. 7. Tap Ok. Fetching a Contact To fetch a contact from another device: NOTE 1. Prior to sending and receiving contacts, a default contact must be set up before attempting to send a contact. Tap and hold on OBEX Object Push and select Connect.
4 - 16 MC75 User Guide 1. Tap and hold on OBEX Object Push and select Connect. The OBEX Object Push window appears. Figure 4-18 OBEX Object Push Window 2. In the Action: drop-down list, select Send A Picture. 3. Tap . The Send Local Picture window appears. Figure 4-19 Send Local Picture Window 4. Navigate to the picture to send to the other device. 5. Tap Open. 6. Tap OK to send the picture to the other device and display a confirmation dialog box on the other device to accept the picture.
Using Bluetooth 4 - 17 2. Ensure that the Headset profile is enabled on the MC75. See Profiles Tab on page 4-32 for more information. 3. Use the Connection Wizard to search for a Bluetooth headset. 4. Select the device and tap Next. 5. Select the Headset service name and select Connect. The MC75 connects to the headset. Refer to the headset user manual for instructions on communicating with a Bluetooth device.
4 - 18 MC75 User Guide Headset icon Figure 4-20 WWAN Bluetooth Audio Notification Dialog Box Serial Port Services Use the wireless Bluetooth serial port connection as you would a physical serial cable connection. Configure the application that will use the connection to the correct serial port. To establish a serial port connection: 1. Ensure the MC75 is discoverable and connectable. See Device Info Tab on page 4-23. 2. Use the Connection Wizard to search for a Bluetooth serial device. 3.
Using Bluetooth 4 - 19 Figure 4-21 ActiveSync Connection Settings Window on PC To establish an ActiveSync connection: 1. Ensure the MC75 is discoverable and connectable. See Device Info Tab on page 4-23. 2. Ensure that the Sync profile is enabled on the MC75. See Profiles Tab on page 4-32 for more information. 3. Use the Connection Wizard to search for a Bluetooth device, such as a PC. In the drop-down list select ActiveSync via Bluetooth. 4. Select the device and tap Next.
4 - 20 MC75 User Guide Personal Area Network Services NOTE This profile supports Ad-hoc and PAN User. Network Access Profile is not supported. Connect two or more Bluetooth devices to share files, collaborate, or play multi-player games. To establish a Personal Area Network connection: 1. Ensure the MC75 is discoverable and connectable. See Device Info Tab on page 4-23. 2. Ensure that the Personal Area Networking profile is enabled on the MC75. See Profiles Tab on page 4-32 for more information. 3.
Using Bluetooth 4 - 21 To bond with a discovered Bluetooth device: NOTE If favorite connections have already been created, the Favorites screen displays. If no favorite connections have been created, the New Connection Wizard screen displays. 1. Tap the Bluetooth icon and select Show BTExplorer. The BTExplorer window appears. 2. Tap Menu > New Connection. The New Connection Wizard window appears. 3. In the drop-down list, select Pair with Remote Device. 4. Tap Next.
4 - 22 MC75 User Guide Figure 4-25 Pairing Status Window 8. Tap Finish. The devices are successfully paired. The device name moves to the Trusted Devices window. Deleting a Bonded Device To delete a device no longer needed: 1. Tap the Bluetooth icon and select Show BTExplorer. The BTExplorer window appears. 2. Tap Menu > Trusted Devices. The Trusted Devices window appears. 3. Tap and hold on the device select Delete Link Key in the pop-up menu. 4. A confirmation dialog appears. Tap Yes.
Using Bluetooth 4 - 23 4. Tap OK to create the bond. The MC75 can now exchange information with the other device. Bluetooth Settings Use the BTExplorer Settings window to configure the operation of the BTExplorer application. Tap Menu > Settings. The BTExplorer Settings window appears. Device Info Tab Use the Device Info tab to configure the MC75’s Bluetooth connection modes. Figure 4-27 BTExplorer Settings - Device Info Tab Device Name Displays the name of the MC75.
4 - 24 MC75 User Guide To add a service: 1. Tap Add. The Add Local Service window displays. Figure 4-29 Add Local Service Window 2. In the list, select a service to add. 3. Tap OK. The Edit Local Service window displays for the selected service. 4. Select the appropriate information and then tap OK. See the following sections for information on the available services. Dial-Up Networking Service Dial-up Networking allows other Bluetooth devices to access a dial-up modem.
Using Bluetooth 4 - 25 Table 4-1 Item Description Local COM Port Select the COM port. Local Baud Rate Select the communication baud rate. Local Port Options Select the port option. File Transfer Service File transfer allows other Bluetooth devices to browse files. Figure 4-31 BTExplorer Settings - File Transfer Information Table 4-2 File Transfer Information Data Item Description Service Name Displays the name of the service.
4 - 26 MC75 User Guide Hands-Free Audio Gateway Service Hands-Free Service Audio Gateway allows connection to hands-free devices. Figure 4-32 BTExplorer Settings - Hands-Free Audio Gateway Table 4-3 Hands-Free Audio Gateway Data item Service Name Description Lists the name of the audio service. Headset Audio Gateway Service Headset Service Audio Gateway allows connection to headset devices.
Using Bluetooth 4 - 27 Figure 4-34 BTExplorer Settings - IrMC Synchronization Table 4-5 IrMC Synchronization Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Phonebook Select the Phonebook checkbox to allow synchronization with the MC75’s contacts. Select Read, Write, Create and/or Delete to allow phonebook permissions.
4 - 28 MC75 User Guide Figure 4-35 BTExplorer Settings - OBEX Exchange Information Table 4-6 OBEX Exchange Information Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Do not allow clients to push objects Disables clients from pushing objects to the MC75. Inbox Directory Select a directory where another Bluetooth device can store files.
Using Bluetooth 4 - 29 Table 4-7 Personal Area Networking Data Item Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list. Options are None, Authenticate, or Authenticate/Encrypt. Support Group Ad-Hoc Networking Select to enable Ad-Hoc networking. Serial Port Service Serial port allows other Bluetooth devices to access COM ports.
4 - 30 MC75 User Guide Figure 4-38 BTExplorer Settings - Security Tab NOTE To use PIN Code, select Authenticate or Authenticate/Encrypt from the Service Security drop-down list on each local service. Table 4-9 Security Tab Data Item Description Use PIN Code (Incoming Connection) Select for automatic use of the PIN code entered in the PIN Code text box. It is recommended not to use this automatic PIN code feature. See Security on page 4-2 for more information. PIN Code Enter the PIN code.
Using Bluetooth 4 - 31 Table 4-10 Discovery Tab Data Item Description Inquiry Length Sets the amount of time the MC75 takes to discover Bluetooth devices in the area. Name Discovery Mode Select either Automatic or Manual to automatically attempt to discover a Bluetooth device's name after finding the device. Discovered Devices - Delete Devices Deletes all discovered devices and link keys from memory.
4 - 32 MC75 User Guide HID Tab Use the HID tab to select The Human Interface Device Profile programming interface defines the protocols and procedures to be used to implement HID capabilities. Provides support for devices such as mice, joysticks, keyboards. Figure 4-41 BTExplorer Settings - HID Tab Table 4-12 HID Tab Data Item Description Enable Key Repeat Enables key repeat functionality. Delay To increase key repeat delay, drag the Delay slider to the right.
Using Bluetooth 4 - 33 The Serial Port profile is always active and cannot be removed. 2. Tap Select All to select all profiles or tap Deselect All to deselect all profiles. 3. Tap Apply to activate the profiles and then Close to exit the application. System Parameters Tab Figure 4-43 BTExplorer Settings - System Parameters Tab Table 4-13 System Parameters Tab Data item Description Page Timeout Sets the amount of time the MC75 searches for a device before moving on the next device.
4 - 34 MC75 User Guide Table 4-14 Miscellaneous tab Data Item Description Highlight Connections Select the connection type to highlight when connected. In the Wizard Mode, the only options are Favorites or None. In the Explorer Mode the options are None, Tree View Only, List View Only, or Tree and List View. Apply Text Style Select the text style to apply to the connection text. Apply Text Color Select the text color to apply to the connection text.
Chapter 5 Using the Phone Introduction Use the MC75 to make phone calls, set up speed dials, keep track of calls, and send text messages. Your wireless service provider may also provide other services such as voice mail, call forwarding, and caller ID. Also use the integrated phone to connect to an ISP or work network in order to browse the Web and read e-mail.
5-2 MC75 User Guide To access the phone keypad tap Start > Phone or press the green phone key on the MC75’s keypad. To receive calls when the MC75 is suspended, leave the phone radio turned on and ensure the MC75 is set to wake with any key. Turning the Phone On and Off Windows Mobile 6 devices include Wireless Manager, which provides a simple method of enabling and disabling the phone. To open Wireless Manager, tap the Connectivity icon. Figure 5-2 Opening Wireless Manager Select Wireless Manager.
Using the Phone 5-3 Audio Modes The MC75 offers three audio modes for use during phone calls: • Handset Mode: Switches audio to the speaker at the top front of the MC75, so you can use the MC75 as a handset. This is the default mode. • Speaker Mode: Use the MC75 as if on speaker phone. Tap the Speaker On button to activate this mode. Tap the Speaker Off button to switch back to handset mode. • Headset Mode: Connect a wired or Bluetooth headset to automatically switch audio to the headset.
5-4 MC75 User Guide Figure 5-4 Using a Headset Using a Bluetooth Headset You can use a Bluetooth headset for audio communication when using an audio-enabled application. See Chapter 4, Using Bluetooth for information on connecting a Bluetooth headset to the MC75. Set the MC75’s volume appropriately before putting the headset on. When a Bluetooth headset is connected the speakerphone is muted. It is recommended for phone conversations to use the Bluetooth Hands-free profile instead of the Headset profile.
Using the Phone 5-5 Phone Volume Slider Figure 5-6 Phone Volume Slider To adjust the volume tap the Speaker icon in the Title bar. Move the slider up or down to adjust the volume. NOTE Adjust the conversation phone volume during a call. Adjusting the volume while not in a call affects the ring and notification sound levels. Making a Call NOTE You can make emergency calls even when the MC75 is locked or when a SIM card is not installed. See Making an Emergency Call on page 5-7 for more information.
5-6 MC75 User Guide Figure 5-7 Contacts Menu 3. Tap Call Work, Call Home or Call Mobile. NOTE To make a call from an open contact, tap the number to call. See On-Device Help for more information about Contacts. Using Call History To make a call using Call History: 1. Tap Start > Phone or press the green phone key on the MC75’s keypad. 2. From the Phone keypad, tap Call History. Phone icon Figure 5-8 Call History 3.
Using the Phone 2. 5-7 From the Phone keypad, tap and hold the speed dial location number assigned to a contact. (To dial a one-digit speed dial location number, tap and hold the speed dial number. To dial a two-digit speed dial location number, tap the first digit and then tap and hold the second digit.) or From the Phone keypad, tap Speed Dial and tap the speed dial location number of the desired contact in the list. Speed Dial Location Number Figure 5-9 Speed Dial Contact List 3.
5-8 MC75 User Guide Figure 5-10 Incoming Call To ignore the incoming call tap Ignore. This may send the caller to voice mail, depending on the service provider. Otherwise, this presents busy signal to the calling party. To end the call tap End or press the red phone key on the MC75 keypad. Incoming Call Features • If you receive a call while in a call, tap Wait to place the call in call waiting. • You can use other programs on the MC75 during a call.
Using the Phone 5-9 To find a contact name: • Enter the first letter of a contact’s first name or last name. Smart Dialing searches for the letter starting from the first character of a contact name as well as from the character that appears after a space, dash, or underscore in a contact name.
5 - 10 MC75 User Guide Mute Icon Figure 5-12 Mute Button and Icon Taking Notes To create a note during a call, tap Note on the display, then enter the note. For more information about creating notes see the Windows On-Device Help. To access a note created during a call: 1. Tap Start > Phone or press the green phone key on the MC75’s keypad. 2. From the Phone keypad, tap Call History. 3. Tap and hold the number or the Note icon for the phone call entry containing the note.
Using the Phone 5 - 11 Figure 5-14 Call History - Notes 5. Tap ok to exit. NOTE Also access notes directly from the Notes application by tapping Start > Notes. Using Speed Dial Create speed dial numbers to dial frequently called numbers with a single tap. Before creating a speed dial entry, ensure the phone number exists in Contacts. Adding a Speed Dial Entry To add a speed dial entry from the phone keypad: 1. Ensure the contact and phone number are in the Contacts list. 2.
5 - 12 MC75 User Guide Figure 5-16 Speed Dial Contact Location 5. In the Location field, tap the up/down arrows to select an available location to assign as the new speed dial entry. The first speed dial location is reserved for voice mail. 6. Tap ok to add the contact to the speed dial list. Figure 5-17 Speed Dial Contact List 7. Tap ok to exit the Speed Dial Contact List. To add a speed dial entry from the Contacts window: 1. Tap Start > Contacts.
Using the Phone 5 - 13 Figure 5-18 Contacts 2. Tap a contact name. 3. Tap Menu > Add to Speed Dial. Figure 5-19 Speed Dial Contact Location 4. Tap the up/down arrows to select an available location to assign as the new speed dial entry. The first speed dial location is reserved for voice mail. 5. Tap ok. Editing a Speed Dial Entry 1. Tap Start > Phone or press the green phone key on the MC75’s keypad. 2. Tap Menu > Speed Dial.
5 - 14 MC75 User Guide Figure 5-20 Speed Dial Contact List 3. Tap and hold the contact name. 4. Tap Edit... . 5. Change the name, phone number, or location information. 6. Tap ok. NOTE Editing names and phone numbers in Speed Dial does not alter contact information in Contacts (Start > Contacts). Deleting a Speed Dial Entry 1. Tap Start > Phone or press the green phone key on the MC75’s keypad. 2. Tap Menu > Speed Dial. 3. Tap and hold the contact name. Figure 5-21 Speed Dial Delete Menu 4.
Using the Phone 5 - 15 Using Call History Use Call History to call someone who was recently called, or recently called in. Call History provides the time and duration of all incoming, outgoing, and missed calls. It also provides a summary of total calls and easy access to notes taken during a call. Table 4-1 lists the call history icons that appear in the Call History window. Table 5-1 Call History Icons Icon Description This icon appears next to the contact information for all outgoing calls.
5 - 16 MC75 User Guide 3. Tap Menu. Figure 5-23 Call History - Tools Menu 4. Select Call Timers... . Figure 5-24 Call History - Call Timers 5. Tap Reset. (The All Calls: counter cannot be reset.) 6. Tap ok to exit the Call Timers window. Deleting Call History Items by Call Date 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap Menu > Call Timers... .
Using the Phone 5 - 17 Figure 5-25 Call History - Call Timers 4. In the Delete call history items older than: drop-down list select a time period on which to base deletion of stored items. 5. Tap ok to exit the Call Timers window. Deleting All Call History Items 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap Menu. Figure 5-26 Call History - Tools Menu 4. Select Delete all calls.
5 - 18 MC75 User Guide Viewing Call Status 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. From the Phone keypad, tap Call History. 3. Tap an entry. The Call Status window appears. Figure 5-28 Call History - Detail NOTE 4. When more than one call is on the phone line, only the duration of the first call is recorded. Tap ok and then ok to exit.
Using the Phone 5 - 19 5. Depending on the item selected, the appropriate window displays. For example, select Send SMS to display the Inbox window. 6. Tap ok to exit the Call History window. Swapping Calls on an MC7506/96 To move between two or more phone calls: 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. Enter the first phone number and press Talk. When the call connects, Hold appears on the keypad.
5 - 20 MC75 User Guide Swapping Calls on an MC7508/98 To swap between two incoming phone calls: 1. Tap Answer to connect to the first call. Figure 5-32 Answer a Call 2. When a second call arrives, tap Answer. The first call is placed on hold. 3. Tap Talk to swap from one call to the other. Figure 5-33 Call Swapping 4. Tap End or press the red phone key on the MC75 keypad to end active call. The remaining call re-connects, tap Answer to connect to the call. 5.
Using the Phone 5 - 21 2. Enter the first phone number and press Talk. When the call connects, Hold appears on the keypad. Figure 5-34 Conference Call - Hold 3. Tap Hold to place the first call on hold. 4. Enter the second phone number and tap Talk. 5. After the call is answered, tap Menu > Conference to place the calls in conference mode. Figure 5-35 Creating a Conference Call 6. Tap Hold to place the conference on hold. 7. Enter another phone number and tap Talk. 8.
5 - 22 MC75 User Guide Figure 5-36 Creating a Private Call Three-way Calling on an MC7508/98 NOTE Three-way Calling may not be available on all services. Please check with your service provider for availability. To create a three-way phone session with two people and you as the initiator: 1. Tap Start > Phone or press the green phone key on the MC75’s keypad to display the Phone keypad. 2. Enter the first phone number and press Talk. 3. To call a second person, tap Keypad.
Using the Phone 5 - 23 Text Messaging Use the Text Messages window to send and receive text messages to and from mobile phones. The text can contain words, numbers, or an alphanumeric combination no longer than 160 characters. Short text messages delivered over mobile networks transmit from the sending MC75, are stored in a central short message center, then forwarded to the destination mobile device. If the recipient is not available, the message is stored and can be sent later.
5 - 24 MC75 User Guide Tap Text Messages. Figure 5-40 Text Messaging on Today Screen The Messaging window appears. Figure 5-41 Messaging Window 2. In the message list, tap a Text Messages. Tap to reply the message. Figure 5-42 Text Messages List NOTE If the phone is turned off and you tried to call the sender, send a reply, or forward the message, you are prompted to turn the phone function on. Sending a Text Message To create a text message: 1.
Using the Phone 5 - 25 2. Tap Menu > Send Text Message. Figure 5-43 Phone Screen Contact List 3. Compose your message. Address Area Message Area Figure 5-44 Create Text Message • The auto-correct feature automatically fixes common spelling errors as you type so your messages are more accurate. • The character counter lets you see and control the size of the message as you compose.
5 - 26 MC75 User Guide If the phone is turned on, your text message is sent. If it’s off, you are prompted to turn on the phone. If you do so, the message is sent; otherwise when you tap ok, the message is saved in the Drafts folder and sent when the phone is turned on. If you are out of coverage area, the message is saved in the Drafts folder and sent when you return to a coverage area.
Using the Phone 5 - 27 3. Select Change and then tap Select. 4. If applicable, sign in with the PIN number for the other line.
5 - 28 MC75 User Guide
Chapter 6 Accessories Introduction MC75 accessories, listed below, provide a variety of product support capabilities. • Four Slot Ethernet Cradle - Charges the MC75 main battery and connects the MC75 with an Ethernet network. • Four Slot Charge Only Cradle - Charges up to four MC75 devices. • Single Slot USB/Serial Cradle - Charges the MC75 main battery and a spare battery. Synchronizes the MC75 with a host computer through a USB connection.
6-2 MC75 User Guide Single Slot USB/Serial Cradle This section describes how to use a Single Slot USB/Serial cradle with the MC75. For USB communication setup procedures refer to the MC75 Integrator Guide. The Single Slot USB/Serial Cradle: • Provides 5.4 VDC power for operating the MC75. • Synchronizes information between the MC75 and a host computer. Refer to the MC75 Integrator Guide for information on setting up a partnership between the MC75 and a host computer. • Charges the MC75’s battery.
Accessories 6-3 Charging the Spare Battery Spare Battery Spare Battery Charging LED Figure 6-2 Spare Battery Charging Battery Charging Indicators The Single Slot USB/Serial Cradle charges the MC75’s main battery and a spare battery simultaneously. The MC75’s charge LED indicates the status of the battery charging in the MC75. See Table 1-2 on page 1-7 for charging status indications. The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle.
6-4 MC75 User Guide Four Slot Ethernet Cradle This section describes how to set up and use a Four Slot Ethernet cradle with the MC75. For cradle communication setup procedures refer to the MC75 Integrator Guide. The Four Slot Ethernet cradle: • Provides 5.4 VDC power for operating the MC75. • Connects the MC75 (up to four) to an Ethernet network. • Simultaneously charges up to four MC75 devices. Charging Insert the MC75 into a slot to begin charging.
Accessories 6-5 Four Slot Charge Only Cradle This section describes how to set up and use a Four Slot Charge Only cradle with the MC75. The Four Slot Charge Only cradle: • Provides 5.4 VDC power for operating the MC75. • Simultaneously charges up to four MC75 devices. Charging Insert the MC75 into a slot to begin charging. Figure 6-4 MC75 Battery Charging Battery Charging Indicators The MC75’s charge LED shows the status of the battery charging in the MC75.
6-6 MC75 User Guide VCD7X00 Vehicle Cradle This section describes how to use a VCD7X00 vehicle cradle with the MC75. For cradle installation and communication setup procedures refer to the MC75 Integrator Guide. Once installed in a vehicle, the cradle: • holds the MC75 securely in place • provides power for operating the MC75 • provides a serial port for data communication between an MC75 and an external device (e.g.
Accessories 6-7 Release Lever Figure 6-6 Removing the MC75 Charging the Spare Battery Insert a spare battery to begin charging: 1. Lift the battery release lever. Battery Release Lever Battery Figure 6-7 Inserting the Spare Battery 2. Insert the spare battery in the spare battery charging slot in the cradle with the charging contacts facing up and to the rear of the cradle. 3. Release the battery release lever. The battery release lever locks the spare battery into place.
6-8 MC75 User Guide Battery Charging Indicators The Vehicle Cradle charges the MC75’s main battery and a spare battery simultaneously. The MC75’s charge LED indicates the status of the battery charging in the MC75. See Table 1-2 on page 1-7 for charging status indications. The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle. See Table 6-2 for charging status indications.
Accessories Four Slot Battery Charger This section describes how to use the Four Slot Battery Charger to charge up to four MC75 batteries. MC75 Battery Shim Installation Before charging a spare battery, snap the MC75 shim into the battery slot as shown in Figure 6-9. Shim Figure 6-9 MC75 Battery Shim Installation NOTE To purchase additional shims, contact your local account manager or Motorola, Inc. Part number: KT-76490-01R. Spare Battery Charging 1. Connect the charger to a power source. 2.
6 - 10 MC75 User Guide Spare Battery Spare Battery Charging LEDs (4) Figure 6-10 Four Slot Battery Charger Battery Charging Indicators The charger has an amber LED for each battery charging well. See Table 6-3 for charging status indications. The 3600 mAh battery fully charges in less than five hours and the 4800 mAh battery fully charges in less than seven hours. Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75.
Accessories 6 - 11 Magnetic Stripe Reader (MSR) This section describes how to set up and use the snap-on MSR with the MC75. The MSR snaps on to the bottom of the MC75 and removes easily when not in use. When attached to the MC75, the MSR allows the MC75 to capture data from magnetic stripe cards. To download MSR data capture software, visit the Motorola web site at http://www.symbol.com/support.
6 - 12 MC75 User Guide Figure 6-12 Magnetic Stripe Card Swiping 5. The application indicates if the data has been read correctly.
Accessories 6 - 13 Debit Card Reader The DCR7X00-100R Debit Card Reader (DCR) snaps onto the bottom of the MC70/MC75 mobile computer to allow easy data capture with the swipe of a magnetic stripe card and personal identification number (PIN) entry using a numeric keypad. This guide describes how to install and use the DCR. Getting Started When using the DCR for the first time, charge the DCR in a cradle for a minimum of three hours. Installation 1.
6 - 14 MC75 User Guide Figure 6-14 DCR Removal Credit Card Transactions Launch a transaction application on the MC75. In the application, select Credit Card transaction. Swipe the credit card through the magnetic stripe reader (MSR) slot, orienting the magnetic stripe as shown. Data encoded on the credit card is captured and, depending on the application, may display in an application data field. Figure 6-15 Swipe Card NOTE Swipe the card in either direction, from left to right, or right to left.
Accessories 6 - 15 Figure 6-16 Swipe Card NOTE Swipe the card in either direction, from left to right, or right to left. For best results, gently press down on the card while swiping to ensure contact with the bottom of the slot. Turn the MC75 over and present the DCR keypad to the customer. The customer enters their PIN following the instructions on the DCR display. Figure 6-17 Enter PIN on DCR Keypad The back of the DCR contains a display and a numeric keypad for entering data.
6 - 16 MC75 User Guide Table 6-4 Keypad Key Descriptions Key Description Numeric Used to enter PIN. Cancel Cancels the current transaction. Clear Clears the entered data. Enter Submits the entered data. Display Messages The follow messages may appear on the DCR display: ENTER PIN - A PIN is required to complete the transaction. PIN ERR - The entered PIN is not between 4 and 12 characters. CANCELED - The transaction was cancelled by the user. COMPLETE - The transaction was completed.
Accessories 6 - 17 • BATT LOW - Battery charge is low. If BATT LOW displays, charge the DCR for approximately three hours. To charge the DCR, place it in a cradle or connect it to a charging cable. The DCR also charges when connected to the MC75 and the transaction application is running.
6 - 18 MC75 User Guide Headset Use the headset to communicate via Voice-Over-IP (VOIP) or for audio playback and telephony applications. To connect the headset, remove the plug from the headset jack at the top of the MC75 and insert the headset connector. Contact a Motorola representative for compatible headsets. For best performance, Motorola recommends a 2.5mm jack headset, p/n 50-11300-050R.
Accessories 6 - 19 Cables This section describes how to set up and use the cables. The cables are available with a variety of connection capabilities. The following communication/charge cables are available: • Serial (RS232) Charge cable (9-pin D female with power input receptacle) • USB Client Charge cable (standard-A connector and a barrel receptacle for power) • Auto charge cable • DEX cable • Modem inverter cable • Charge only cable.
6 - 20 MC75 User Guide 2. Slide the bottom of the MC75 into the connector end of the communication/charge cable and gently press in until it latches into the MC75. The MC75 amber Charge LED indicates the MC75 battery charging status. The 3600 mAh standard battery charges in less than five hours and the 4800 mAh standard battery charges in less than seven hours. See Table 1-2 on page 1-7 for charging status indications. 3.
Chapter 7 Maintenance & Troubleshooting Introduction This chapter includes instructions on cleaning and storing the MC75, and provides troubleshooting solutions for potential problems during MC75 operation. Maintaining the MC75 For trouble-free service, observe the following tips when using the MC75: • Do not scratch the screen of the MC75. When working with the MC75, use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen.
7-2 MC75 User Guide • A screen protector is applied to the MC75. Motorola recommends using this to minimize wear and tear. Screen protectors enhance the usability and durability of touch screen displays. Benefits include: • Protection from scratches and gouges • Durable writing and touch surface with tactile feel • Abrasion and chemical resistance • Glare reduction • Keeping the device’s screen looking new • Quick and easy installation.
Maintenance & Troubleshooting 7-3 Cleaning CAUTION Always wear eye protection. Read warning label on compressed air and alcohol product before using. If you have to use any other solution for medical reasons please contact Motorola for more information. WARNING! Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the device and clean the product immediately in accordance with these guidelines.
7-4 MC75 User Guide 8. Spray compressed air on the connector area by pointing the tube/nozzle about ½ inch away from the surface. CAUTION: Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face. 9. Inspect the area for any grease or dirt, repeat if required. Cleaning Cradle Connectors To clean the connectors on a cradle: 1. Remove the DC power cable from the cradle. 2. Dip the cotton portion of the cotton tipped applicator in isopropyl alcohol. 3.
Maintenance & Troubleshooting 7-5 Troubleshooting MC75 Table 7-1 Troubleshooting the MC75 Problem MC75 does not turn on. Cause Solution Lithium-ion battery not charged. Charge or replace the lithium-ion battery in the MC75. Lithium-ion battery not installed properly. Install the battery properly. See Installing the Main Battery on page 1-6. System crash. Perform a warm boot. If the MC75 still does not turn on, perform a cold boot. See Resetting the MC75 on page 2-14. Battery failed.
7-6 MC75 User Guide Table 7-1 Troubleshooting the MC75 (Continued) Problem MC75 shuts off. Tapping the window buttons or icons does not activate the corresponding feature. A message appears stating that the MC75 memory is full. MC75 keeps powering down to protect memory contents. Cause Solution MC75 is inactive. The MC75 turns off after a period of inactivity. If the MC75 is running on battery power, set this period from 1 to 5 minutes, in one-minute intervals.
Maintenance & Troubleshooting 7-7 Table 7-1 Troubleshooting the MC75 (Continued) Problem The MC75 does not accept scan input. Cause Solution Scanning application is not loaded. Load a scanning application on the MC75. See the system administrator. Unreadable bar code. Ensure the symbol is not defaced. Distance between exit window and bar code is incorrect. Place the MC75 within proper scanning range. MC75 is not programmed for the bar code.
7-8 MC75 User Guide Table 7-2 Troubleshooting Bluetooth Connection (Continued) Problem Cause Solution Can’t make my Ericsson R520 phone discoverable. You attempted to bond with the phone, and when the phone presented a “pairing query,” you entered No. This prevents the phone from being discoverable until it is reset. Reset the phone by removing its battery. There is a delay in the Bluetooth stack re-initializing during a resume from suspend. This is normal behavior. No solution required.
Maintenance & Troubleshooting 7-9 Table 7-3 Troubleshooting the Single Slot USB/Serial Cradle (Continued) Symptom MC75 battery is not charging. Spare battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action MC75 was removed from cradle or cradle was unplugged from AC power too soon. Ensure cradle is receiving power. Ensure MC75 is seated correctly. Confirm main battery is charging under Start > Settings > System > Power.
7 - 10 MC75 User Guide Four Slot Ethernet Cradle Table 7-4 Troubleshooting the Four Slot Ethernet Cradle Symptom Attempt by the MC75 to ActiveSync failed. During communication, no data transmits, or transmitted data was incomplete. Cause Solution MC75 removed from the cradle while the LED was blinking green. Wait one minute and reinsert the MC75 in the cradle. This allows the cradle to attempt another synchronization. Using an outdated version of ActiveSync. Visit http://www.microsoft.
Maintenance & Troubleshooting 7 - 11 Table 7-4 Troubleshooting the Four Slot Ethernet Cradle (Continued) Symptom Battery is not charging. Cause Solution MC75 removed from the cradle too soon. Replace the MC75 in the cradle. The 3600 mAh battery fully charges in less than six hours. Tap Start > Settings > System > Power to view battery status. Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery. MC75 is not inserted correctly in the cradle.
7 - 12 MC75 User Guide Four Slot Battery Charger r Table 7-6 Troubleshooting The Four Slot Battery Charger Symptom Battery not charging. Possible Cause Action Battery was removed from the charger or charger was unplugged from AC power too soon. Re-insert the battery in the charger or re-connect the charger’s power supply. The 3600 mAh battery fully charges in less than six hours. Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
Maintenance & Troubleshooting 7 - 13 Magnetic Stripe Reader Table 7-8 Troubleshooting the Magnetic Stripe Reader Symptom MSR cannot read card. MC75 battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action MSR removed from MC75 during card swipe. Reattach MSR to MC75 and reswipe the card. Faulty magnetic stripe on card. See the system administrator. MSR application is not installed or configured properly.
7 - 14 MC75 User Guide
Appendix A Technical Specifications MC75 Technical Specifications The following tables summarize the MC75’s intended operating environment and technical hardware specifications. MC75 Table A-1 MC75 Technical Specifications Item Description Physical Characteristics Dimensions Length: 17.9 cm (7.05 in.) Width: 8.4 cm (3.30 in.) Depth: 4.4 cm (1.70 in.) Weight 422 grams (14.90 oz) - with 3600 mAh battery 446g (15.70 oz) - with 4800 mAh battery Display Transflective color 3.
A-2 MC75 User Guide Table A-1 MC75 Technical Specifications (Continued) Item Description Notification Vibrator and LED Keypad Options 26 key numeric 44 key QWERTY, 44 key AZERTY, 44 key QWERTZ Audio Speaker, receiver, microphone, headset jack, software support for full duplex record and playback (stereo) Performance Characteristics CPU XScale™ Bulverde PXA270 processor at 624 MHz Operating System Microsoft® Windows Mobile™ 6 Memory 128MB RAM/256MB FLASH Interface/Communications RS-232, USB
Technical Specifications A-3 Table A-1 MC75 Technical Specifications (Continued) Item Description Operating Channels Chan 8-169 (5040 – 5845 MHz) Chan 1-13 (2412-2472 MHz) Chan 14 (2484 MHz) Japan only Actual operating frequencies depend on regulatory rules and certification agency Security WPA2, WPA, WEP (40 or 128 bit), TKIP, TLS, TTLS (MS-CHAP), TTLS (MS-CHAP v2), TTLS (CHAP), TTLS-MD5, TTLS-PAP, PEAP-TLS, PEAP (MS-CHAP v2), AES, LEAP Spreading Technique Direct Sequence Spread Spectrum (DSSS) a
A-4 MC75 User Guide Table A-1 MC75 Technical Specifications (Continued) Item Description Pitch Angle +/- 60° from normal Skew Tolerance +/- 50° from normal Ambient Light Total darkness to 9,000 ft.
Technical Specifications A-5 Table A-2 Data Capture Options (Continued) Item Description Imaging Decode Capability Code 39 Codabar Discrete 2 of 5 EAN-13 UPC/EAN supplementals Webcode Composite C Macro PDF-417 Data Matrix US Planet Canadian 4-state Chinese 2 of 5 microQR GS1 DataBar Limited GS1 DataBar Expanded Stacked Camera Decode Capability Code 39 Codabar Discrete 2 of 5 EAN-13 UPC/EAN supplementals Webcode Composite C Macro PDF-417 Data Matrix US Planet Canadian 4-state GS1 DataBar GS1 DataBar
A-6 MC75 User Guide MC75 Accessory Specifications Single Slot USB/Serial Cradle Table A-3 Single Slot USB/Serial Cradle Technical Specifications Feature Description Dimensions Length: 14.54 cm (5.72 in.) Width: 11.05 cm (4.35 in.) Height: 9.10 cm (3.58 in.) Weight 196 g (6.
Technical Specifications Table A-4 Four Slot Ethernet Cradle Technical Specifications (Continued) Feature Description Charging Temperature 0°C to 40°C (32°F to 104°F) Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature Electrostatic Discharge (ESD) +/- 15 kV air +/- 8 kV contact Four Slot Charge Only Cradle Table A-5 Four Slot Charge Only Cradle Technical Specifications Feature Description Dimensions Length: 46.80 cm (18.42 in.
A-8 MC75 User Guide Table A-6 Four Slot Battery Charger Technical Specifications (Continued) Feature Description Power Consumption 30 watts Operating Temperature 0°C to 50°C (32°F to 122°F) Storage Temperature -40°C to 70°C (-40°F to 158°F) Charging Temperature 0°C to 40°C (32°F to 104°F) Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.
Appendix B Voice Quality Manager Introduction The Voice Quality Manager (VQM) is a software package that resides on the MC75. VQM enables a set of features for Voice over WiFi (VoWiFi) calls, and a sub-set of those features for cellular line (GSM or CDMA) calls. The VQM user interface is designed to be intuitive and easy to use, so complex tasks such as enabling the Acoustic Echo Canceller (AEC) while a call is in progress are done with very little or no user intervention.
B-2 MC75 User Guide Audio Modes The MC75 can be in any one of the seven different audio modes. The mode is visually indicated by the VQM icon on the title bar. VQM icon Figure B-1 VQM Icon in Title Bar The VQM icon indicates that the device is in speakerphone mode without Acoustic Echo Cancellation (indicated by the gray VQM icon). The audio modes and their corresponding VQM title bar icons are: Table B-1 VQM Icons Icon Description Speakerphone with Acoustic Echo Cancellation.
Voice Quality Manager B-3 The table below lists the current audio mode and the subsequent audio mode after tapping the VQM icon. Table B-2 Changing Audio Modes Audio Mode before Tapping VQM Icon Audio Mode after Tapping VQM Icon Speakerphone Handset Handset Speakerphone Wired headset Wired headset Bluetooth headset Speakerphone If the audio mode is set to speakerphone and the user taps the VQM icon, the audio mode changes to handset.
B-4 MC75 User Guide Voice Packet Prioritization IP soft phones transmit voice packets in the same manner as any other application that sends data over the network. On a network with different types of traffic, voice packets are given the same priority as any other traffic, and therefore may be subject to delays. WiFi Multi-media (WMM) is a solution to this problem. WMM is a specification that supports prioritizing traffic, and “higher-priority” packets can be given preferential treatment.
Glossary A API. An interface by means of which one software component communicates with or controls another. Usually used to refer to services provided by one software component to another, usually via software interrupts or function calls Aperture. The opening in an optical system defined by a lens or baffle that establishes the field of view. Application Programming Interface. See API. ANSI Terminal. A display terminal that follows commands in the ANSI standard terminal language.
Glossary - 2 MC75 User Guide Bar Width. Thickness of a bar measured from the edge closest to the symbol start character to the trailing edge of the same bar. BIOS. Basic Input Output System. A collection of ROM-based code with a standard API used to interface with standard PC hardware. Bit. Binary digit. One bit is the basic unit of binary information. Generally, eight consecutive bits compose one byte of data. The pattern of 0 and 1 values within the byte determines its meaning. Bits per Second (bps).
Glossary - 3 Codabar. A discrete self-checking code with a character set consisting of digits 0 to 9 and six additional characters: (“-”, “$”, “:”, “/”, “,” and “+”). Code 128. A high density symbology which allows the controller to encode all 128 ASCII characters without adding extra symbol elements. Code 3 of 9 (Code 39). A versatile and widely used alphanumeric bar code symbology with a set of 43 character types, including all uppercase letters, numerals from 0 to 9 and 7 special characters (“-”, “.
Glossary - 4 MC75 User Guide Device Configuration Package. The Symbol Device Configuration Package provides the Product Reference Guide (PRG), flash partitions, Terminal Configuration Manager (TCM) and the associated TCM scripts. With this package hex images that represent flash partitions can be created and downloaded to the mobile computer. Discrete Code. A bar code or symbol in which the spaces between characters (intercharacter gaps) are not part of the code. Discrete 2 of 5.
Glossary - 5 H Hard Reset. See Cold Boot. Hz. Hertz; A unit of frequency equal to one cycle per second. Host Computer. A computer that serves other terminals in a network, providing such services as computation, database access, supervisory programs and network control. High-Speed Downlink Packet Access (HSDPA).
Glossary - 6 MC75 User Guide accepts “packets” from the layer 4 transport protocol (TCP or UDP), adds its own header to it and delivers a “datagram” to the layer 2 data link protocol. It may also break the packet into fragments to support the maximum transmission unit (MTU) of the network. IP Address. (Internet Protocol address) The address of a computer attached to an IP network. Every client and server station must have a unique IP address. A 32-bit address used by a computer on a IP network.
Glossary - 7 MDN. Mobile Directory Number. The directory listing telephone number that is dialed (generally using POTS) to reach a mobile unit. The MDN is usually associated with a MIN in a cellular telephone -- in the US and Canada, the MDN and MIN are the same value for voice cellular users. International roaming considerations often result in the MDN being different from the MIN. MIL. 1 mil = 1 thousandth of an inch. MIN. Mobile Identification Number.
Glossary - 8 MC75 User Guide PC Card. A plug-in expansion card for laptop computers and other devices, also called a PCMCIA card. PC Cards are 85.6mm long x 54 mm wide, and have a 68 pin connector. There are several different kinds: Type I; 3.3 mm high; use - RAM or Flash RAM Type II; 5 mm high; use - modems, LAN adaptors Type III; 10.5 high; use - Hard Disks PCMCIA. Personal Computer Memory Card Interface Association. See PC Card. Percent Decode.
Glossary - 9 RS-232. An Electronic Industries Association (EIA) standard that defines the connector, connector pins, and signals used to transfer data serially from one device to another. S Scan Area. Area intended to contain a symbol. Scanner. An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds to the bars and spaces of the symbol.
Glossary - 10 MC75 User Guide Symbol. A scannable unit that encodes data within the conventions of a certain symbology, usually including start/stop characters, quiet zones, data characters and check characters. Symbol Aspect Ratio. The ratio of symbol height to symbol width. Symbol Height. The distance between the outside edges of the quiet zones of the first row and the last row. Symbol Length.
Glossary - 11 U UDP. User Datagram Protocol. A protocol within the IP protocol suite that is used in place of TCP when a reliable delivery is not required. For example, UDP is used for real-time audio and video traffic where lost packets are simply ignored, because there is no time to retransmit. If UDP is used and a reliable delivery is required, packet sequence checking and error notification must be written into the applications. UPC. Universal Product Code. A relatively complex numeric symbology.
Glossary - 12 MC75 User Guide
Index Numerics 1-D bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29 2-D bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29 A accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 auto charge cable . . . . . . . . . . . . . . . . . . . . . . . . 1-3 cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3, 6-19 charge cable . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 2 MC75 User Guide charging indicators . . . . . . . . . . . . . . . . . . . . . . 6-10 battery chargers communication/charge cables . . . . . . . . . . . . . 6-19 LED indicators . . . . . . . . . . . . . . . . . . . . . . 6-20 four slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 communication/charge cables . . . . . . . . . . . . . 6-19 using four slot battery charger . . . . . . . . . . . . . .
Index - 3 scan range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30 scanning . . . . . . . . . . . . . . . . . . . . . 2-30, 2-31, 2-32 two dimensional bar codes . . . . . . . . . . . . . . . . 2-29 deleting Bluetooth bond . . . . . . . . . . . . . . . . . . . . . . 4-22 DEX cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3, 6-19 digital camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30 display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 4 MC75 User Guide M magnetic stripe reader . . . . . . . . . . . . . . . 1-3, 6-11, 6-18 installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11 magnetic stripe reading . . . . . . . . . . . . . . . . . . . 6-11 main battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4, 1-7 installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Media Player . . . . . . . .
Index - 5 certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 customer feedback . . . . . . . . . . . . . . . . . . . . . . . 2-8 encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 error reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 external GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 GPS Setup . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 6 MC75 User Guide WPAN Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii Z Zebra printer cable . . . . . . . . . . . . . . . . . . . . . . . . .
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.motorola.com/enterprisemobility MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners. © Motorola, Inc.
