HS3100 Rugged Bluetooth Headset User Guide MN-002774-03EN
HS3100 RUGGED BLUETOOTH HEADSET USER GUIDE MN-002774-03EN Rev.
ii HS3100 Rugged Bluetooth Headset User Guide Revision History Changes to the original guide are listed below: Change Date Description Rev A - 01 09/2016 Initial Release Rev A - 02 11/2016 Update to remove Mute Microphone
TABLE OF CONTENTS Revision History ................................................................................................................................. ii About This Guide Introduction ........................................................................................................................................ v Chapter Descriptions ......................................................................................................................... v Notational Conventions .......
iv HS3100 Rugged Bluetooth Headset User Guide Position the Boom .......................................................................................................................... Adjust the OTH Headband ............................................................................................................. Adjust the Microphone ................................................................................................................... Adjust the Microphone Boom ........................
ABOUT THIS GUIDE Introduction This guide provides information about using the HS3100 Rugged Bluetooth Over-the Head (OTH) and Behind-the-Neck (BTN) Headsets. NOTE Pictures in this guide are samples and can differ from the actual headset. Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started, provides an overview, features, and getting started. • Chapter 2, Pairing the Headset, explains the various ways to pair the headset.
vi HS3100 Rugged Bluetooth Headset User Guide • Italics are used to highlight the following: • Chapters and sections in this guide • Related documents • Bold text is used to highlight the following: • Dialog box, window and screen names • Drop-down list and list box names • Check box and radio button names • Icons on a screen • Key names on a keypad • Button names on a screen. • Bullets (•) indicate: • Action items • Lists of alternatives • Lists of required steps that are not necessarily sequential.
CHAPTER 1 GETTING STARTED Headset Overview The HS3100 Rugged Bluetooth Headset comes in two configurations; Over-the-Head (OTH) and Behind-the-Neck (BTN) headbands. NOTE This guide applies to both the OTH and BTN headband models, unless otherwise noted.
1-2 HS3100 Rugged Bluetooth Headset User Guide Headset Configurations Table 1-1 Headset Configurations Model Configuration Includes HS3100-OTH Over-the-Head Headband Left or Right Side Boom Placement HS3100 Boom Module OTH Headband Windscreen Battery HS3100-BTN-L Behind-the-Neck Headband Left Side Boom Placement HS3100 Boom Module BTN Headband Windscreen Battery
Getting Started Over-the-Head (OTH) Features Adjustable OTH Headband T-Bar Battery Ear Pad MultiFunction Button with LED Indicator Flexible Microphone Boom NFC Tag Figure 1-1 Volume Buttons Disassembly Knob Microphone with Windscreen HS3100-OTH Bluetooth Headset Behind-the-Neck (BTN) Features BTN Headband Left Placement Ear Pad Battery Flexible Microphone Boom NFC Tag Microphone with Windscreen Figure 1-2 Multi- Function Button with LED Indicator Volume Buttons Disassembly Knob HS3100-BTN-L
1-4 HS3100 Rugged Bluetooth Headset User Guide Unpacking Carefully remove all protective material from the headset and save the shipping container for later storage and shipping. Verify the following items are in the box: • Headset: • Headband Module • Boom Module • Battery • Quick Start Guide Inspect the equipment for damage. if any equipment is missing or damaged, contact the Zebra Support Center immediately. See Service Information on page ii-vi for contact information.
Getting Started Charging The headset batteries are charged in a toaster which uses either a one slot cradle or a five slot cradle.
1-6 HS3100 Rugged Bluetooth Headset User Guide Charge the Battery in the Battery Charger Although the batteries come partially charged, it is recommended to fully charge them before first use. Allow up to three and a half hours for a full charge. To charge the battery: Insert the battery into the charger with the contacts facing forward.
Getting Started Insert the Battery in the Headset To insert the battery: 1. Insert the battery with the contacts facing outward into the battery slot. 2. Push the battery into the slot until it is firmly secure.
1-8 HS3100 Rugged Bluetooth Headset User Guide Power On the Headset To turn the power on: 1. Press the Multi-Function button (MFB). 2. Wait for the headset LED to illuminate blue and flash three times. The headset is ready to use.
Getting Started LED Indicator and Headset Status Table 1-5 LED Indicator and Headset Status LED Indicator Headset Status Three Blue Flashes Power On Three Red Flashes Power Off Blue and Red Alternate Flashes Pairing Mode Slow Blue Flash Connected Steady Blue Not Connected Slow Two Red Flashes Low Battery 1-9
1 - 10 HS3100 Rugged Bluetooth Headset User Guide
CHAPTER 2 PAIRING THE HEADSET Methods of Pairing the Headset The headset can be paired with other Bluetooth devices in the following ways: NFC Tag Figure 2-1 NFC Pairing • Standard Bluetooth pairing where the headset is discovered by the host. • Bypassing device discovery using a multi-modal interface: • Scan-to-pair - the host gets the headset MAC address through a scan and connects with it. • Tap-to-pair - with hosts having an NFC reader, the host gets the MAC address through NFC and connects with it.
2-2 HS3100 Rugged Bluetooth Headset User Guide
CHAPTER 3 ADJUSTING THE HEADSET Introduction This chapter explains how to adjust the headset for the proper fit and maximum comfort during use. Position the Boom To position the boom: Rotate the boom for left side or right side placement. CAUTION Do not rotate the boom beyond the stop point. Left Side Boom Placement Figure 3-1 Right Side Boom Placement Position the Boom NOTE Applies to OTH model. The BTN model has only left side boom placement.
3-2 HS3100 Rugged Bluetooth Headset User Guide Adjust the OTH Headband To adjust the OTH headband: 1. Squeeze the headband for a tighter fit to the head. Notice that the headband clicks as it is positioned into place. 2. Position the ear pad in the center of the ear. 3. Position the T-Bar above the ear, half way between the top of the ear and the top of the head.
Adjusting the Headset Adjust the Microphone To adjust the microphone: Position the microphone icon so that it is facing your mouth. Microphone Icon Figure 3-3 Adjust the Microphone Adjust the Microphone Boom To adjust the microphone boom: Place the microphone two finger’s width away from the corner of your mouth, so it is slightly to one side.
3-4 HS3100 Rugged Bluetooth Headset User Guide
CHAPTER 4 USING THE HEADSET Introduction This chapter provides basic instructions for using the headset. Adjust the Volume To adjust the volume: Press the Volume Up (+) or Volume Down (-) buttons as desired. Volume UP/DOWN Buttons Figure 4-1 Adjust the Volume Audio Tones The following transitions and states are associated with the audio tones listed.
4-2 HS3100 Rugged Bluetooth Headset User Guide Table 4-1 Audio Tones Transition or State Audio Tones Start Pairing Two short low tones Successful Pairing Three rising tones Headset Connected One tone Link Lost Two low tones followed by a high tone Low Battery Two short tones every two minutes until shutdown Mute Two descending tones Un-mute Two rising tones Power Up Four tones Power Down Four descending tones
CHAPTER 5 MAINTENANCE AND TROUBLESHOOTING Introduction This chapter includes instructions on replacing parts and accessories, safety and battery guidelines, cleaning and storing the headset and provides troubleshooting solutions for potential problems during operation. Maintaining the HS3100 Headset For proper maintenance and maximum operating use and comfort, various parts and accessories can be replaced. Replace T-Bar To replace the T-Bar: 1. Pull and remove the T-Bar off the headband.
5-2 HS3100 Rugged Bluetooth Headset User Guide 2. Align the T-Bar slot with the end of the headband and push the replacement T-Bar on the headband until firmly secured. Figure 5-2 Replace T-Bar NOTE Applies to OTH model. Replace Headband To replace the headband: 1. Loosen the screw.
Maintenance and Troubleshooting 5 - 3 2. Disassemble the headset to replace the headband. Figure 5-4 Disassemble headset Replace Ear Pad To replace the ear pad: 1. Firmly grip and pull the ear pad and inner casing.
5-4 HS3100 Rugged Bluetooth Headset User Guide 2. Align and snap the new ear pad into position.
Maintenance and Troubleshooting 5 - 5 Remove the Battery To remove the battery: Firmly grip the outer battery casing, and pull tightly. Figure 5-7 Remove the battery Replace Windscreen To replace the windscreen: 1. Pull and remove the windscreen off the microphone. Figure 5-8 2. Remove Windscreen Align and slide the replacement windscreen over the microphone.
5-6 HS3100 Rugged Bluetooth Headset User Guide Maintain Headset in a Freezer Environment 1. When working in a freezer environment, replace the windscreen every four hours, or when it is wet or frozen. 2. If the microphone stops working, it could be wet. Remove the windscreen, shake the microphone boom, and place a dry windscreen on the microphone boom. Be careful not to squeeze the wet windscreen while it is on the microphone boom.
Maintenance and Troubleshooting 5 - 7 • Seek medical advice immediately if a battery has been swallowed. • In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice. • If you suspect damage to your equipment or battery, call Customer Support to arrange for inspection. See Service Information on page ii-vi for contact information.
5-8 HS3100 Rugged Bluetooth Headset User Guide Troubleshooting This section provides troubleshooting solutions for potential problems during HS3100 operations. Table 5-1 Troubleshooting Problem Solution Operating Headset does not turn on - Verify the battery is fully inserted in the headset. - Verify the battery is charged. Pairing Headset does not pair - Verify headset is off when beginning the pairing process. - Verify intended Bluetooth device is on.
APPENDIX A ACCESSORIES This appendix provides information about the HS3100-OTH and HS3100-BTN-L accessories. Parts and Accessories The following table lists the part numbers for the headsets and available accessories.
A - 2 HS3100 Rugged Bluetooth Headset User Guide Table A-1 Parts and Accessories (Continued) Part/Accessory 8-Slot-Battery Charger & 8-Slot-WT6000 Charger Part Number Description SAC-HS3100-B8W8-01 Charges up to eight HS3100 batteries and up to eight WT6000 devices CBL-HS3100-CUC1-01 USB Type-A 36" (0.
APPENDIX B TECHNICAL SPECIFICATIONS This section provides technical specifications for the HS3100 Bluetooth Headset and charging cradles HS3100 Technical Specifications Table B-1 HS3100 Bluetooth Headset Technical Specifications Item Description Physical Characteristics Weight 4 oz./115 g (with battery) Wearing Styles Over-the-head headband Behind-the-neck headband Field Replaceable Parts Headband, battery, ear pad, windscreen, T-bar Power Li-ion 220 mAh, 3.
B - 2 HS3100 Rugged Bluetooth Headset User Guide Table B-1 HS3100 Bluetooth Headset Technical Specifications (Continued) Item Description Receive Frequency Response 300 Hz to 6 kHz Speaker Sensitivity 89 dB SPL with 1.0 Vrms @ 1 kHz Bluetooth Bluetooth Class II, v 3.0; Bluetooth Hands-free Profile (HFP 1.6) NFC NFC tag used for Tap-to-Pair User Environment Zebra Mobile Computers Compatibility Visit www.zebra.com/hsheadsets for the most current list of compatible mobile computers.
Technical Specifications B - 3 8-Slot Battery Charger Technical Specifications Table B-2 8-Slot Battery Charger Technical Specifications Item Description Dimensions Height: 74.1 mm Width: 97.8 mm Depth: 134.7 mm Weight 439.8 g Input Voltage 12 V Power Consumption 5.82 Watt (Full load), 0.
B - 4 HS3100 Rugged Bluetooth Headset User Guide 8-Slot-Battery Charger & 8-Slot-WT6000 Charger Technical Specifications Table B-3 8-Slot Battery Charger & 8-Slot-WT6000 Charger Technical Specifications Item Description Dimensions Height: 87.1 mm Width: 134.7 mm Depth: 488.4 mm Weight 2.2 kg Input Voltage 12 V Power Consumption 60 Watt (Full load), 0.
INDEX A adjust the microphone . . . . . . . . . . . . . . . . . . . . . . . . adjust the microphone boom . . . . . . . . . . . . . . . . . . . adjust the OTH headband . . . . . . . . . . . . . . . . . . . . . audio tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P 3-3 3-3 3-2 4-1 pairing methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . parts and accessories . . . . . . . . . . . . . . . . . . . . . . . . position the boom . . . . . . . . . . . . . . . . . . . . . . .
Index - 2 HS3100 Rugged Bluetooth Headset User Guide
Zebra Technologies Corporation, Inc. 3 Overlook Point Lincolnshire, IL 60069, U.S.A. http://www.zebra.com ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2020 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
