ET51/56 Enterprise Tablet Quick Reference Guide
ET51/56 Enterprise Tablet Copyright ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2019 Zebra Technologies Corporation and/or its affiliates. All rights reserved. COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to www.zebra.com/copyright. WARRANTY: For complete warranty information, go to www.zebra.com/warranty.
Quick Reference Guide 3 Introduction The ET51 is a wireless LAN (WLAN) tablet and the ET56 is a wireless WAN (WWAN) tablet. Features 1 1 Item 2 3 4 2 3 4 2 5 5 2 Description 1 Ambient Light Sensor - Recognizes the ambient light and adjusts the display brightness (if enabled). 2 Front Microphones - Use for voice communications or audio recordings. 3 Front Facing Camera - Use for video conferencing or capturing images and video.
ET51/56 Enterprise Tablet 11 6 7 8 Item 10 9 Description 6 Rear Camera - Use for high resolution images and video. 7 Camera LED Flash - Provides illumination for the camera. 8 Power Button - Push once to start the device; push it again to enable sleep mode. Push and hold it to shut down the device. 9 Volume Key - Push the left side to reduce the volume. Press the right side to increase the volume. 10 USB-C Interface - Provides for communication.
Quick Reference Guide 5 Installing a micro SD Card or SIM Card To install a microSD card and/or nano SIM card (ET56 only): 1. Press the Power button to turn off the device. 2. Lift the notched corner of the battery cover. 3. Carefully lift the battery cover off the device. 4. On the 8” version, push the two locking tabs up, then pull up on the tab to remove battery. On the 10” version, push the two locking tabs up (1), then, using index fingers, lift the battery up (2). Locking Tabs 8.
ET51/56 Enterprise Tablet 5. Insert the microSD card with contacts facing down. 8.4” Version 10.1” Version 6. Push the micro SD card in and ensure that it locks into place. 7. Insert the nano SIM card with contacts facing down. NAN O NA NO 8.4” Version 10.1” Version 8. Push the SIM card in and ensure that it locks into place. 9. Replace the battery. CAUTION: Be aware of the orientation of the battery cover. Failure to replace the battery cover properly may damage the battery cover.
Quick Reference Guide 7 10. Align the tabs on the underside of the cover with the slot around the battery well. Make sure that the notch on the battery cover is at the bottom left cover of the device. 11. Carefully press down around the edge of the cover. Make sure that the cover is seated properly. 12. Press Power button to turn on the device. Charging the Device Use the Communication and Charging Cradle, Rugged Communication and Charging Cradle or Charge Only Cradle to charge the device.
ET51/56 Enterprise Tablet 1. If using the Communication and Charging Cradle, open the bottom access door and hold it to the back of the tablet. 2. Align the device with the alignment pins on the cradle. 3. Insert the device into the cradle. Note that the Communication Cradle contains a locking mechanism that locks the device to the cradle.
Quick Reference Guide 9 4. The Charging LED indicates charging. 5. To remove the device from the Charge Only cradle, hold the cradle down with one hand and lift the device. To remove the device from either Communication Cradle, press the release button on the right side of the cradle and lift the device. Use thumb to hold down the cradle. The 8.4” tablet main battery charges from fully depleted to 90% in approximately 2 hours and from fully depleted to 100% in approximately 3 hours. The 10.
ET51/56 Enterprise Tablet Reading NFC Cards The device supports reading NFC cards. The NFC antenna is located on the back of the device under the NFC logo. With an NFC enabled application open, bring the NFC card toward the antenna. Depending upon the application, an audio or visual indication indicates successful reading of the card. NFC Antenna Location Regulatory Information This device is approved under Zebra Technologies Corporation.
Quick Reference Guide • 11 Telit LN940A9 PCI Express radio card, FCC ID: RI7LN940A (LTE, HSPA+) Bluetooth® Wireless Technology This is an approved Bluetooth® product. For more information or to view the End Product Listing, please visit www.bluetooth.org/tpg/listings.cfm.
ET51/56 Enterprise Tablet Frequency of Operation – FCC and IC 5 GHz Only Industry Canada Statement CAUTION: The device for the band 5,150 - 5,250 MHz is only for indoor usage to reduce potential for harmful interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5,250 5,350 MHz and 5,650 - 5,850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
Quick Reference Guide 13 Vehicle Installation RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer about any equipment that has been added to your vehicle. An air bag inflates with great force.
ET51/56 Enterprise Tablet Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, or healthcare facilities. These requests are designed to prevent possible interference with sensitive medical equipment.
Quick Reference Guide 15 This device was tested for typical body-worn operation. Use only Zebra tested and approved belt-clips, holsters, and similar accessories to ensure EU Compliance. US and Canada Co-located statement To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located or operating in conjunction with any other transmitter/antenna except those already approved in this filling.
ET51/56 Enterprise Tablet • Model: AMME3735 (7.6V DC, 3,300 mAh) for 8.4" ET51AE, ET56BE • Model: AMME3950 (7.7V DC, 4,950 mAh) for 10.1" ET51AT, ET56BT • Model: BT-000381 (3.8V DC, 6,060 mAh) for 8.4" ET51CE, ET56DE • Model: BT-000382 (3.8V DC, 8,760 mAh) for 10.1" ET51CT Zebra approved rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations to how long a battery can operate or be stored before needing replacement.
Quick Reference Guide 17 • In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice. • If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection. Removing the Battery 1. Lift the notched corner of the battery cover. 2. Carefully lift the battery cover off the device. 3. On the 8.
ET51/56 Enterprise Tablet Radio Frequency Interference Requirements-FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Quick Reference Guide 19 Etiquette de marquage: Le terme "IC" avant la certification radio signifie que le produit est compatible avec le spécification Industrie Canada Marking and European Economic Area (EEA) The use of 5 GHz RLAN throughout the EEA has the following restrictions: • 5.15 - 5.35 GHz is restricted to indoor use only. Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directives, 2014/53/EU and 2011/65/EU.
• ET51/56 Enterprise Tablet 5.725 a 5.850MHz Además, de acuerdo con Resolución 755, para la banda 5150-5250MHz la operación del equipo estará restringida al interior de inmuebles y la densidad de potencia radiada máxima no supera 7,5mW/MHz en cualquier banda de 1MHz y 0.1875mW/25kHz en cualquier banda de 25kHz. Para la tecnología NFC en la banda 13.553 a 13.567 kHz, la intensidad de campo eléctrico no excederá 20 mV/m a 30 metros, conforme a Resolucion 755 parte Art 1. e).
Quick Reference Guide 21 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停 用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 應避免影響附近雷達系統之操作 減少電磁波影響，請妥適使用 台灣斑馬科技股份有限公司 / 台北市信義區松高路 9 號 13 樓 Thailand เครื่ องโทรคมนาคมและอุ ปกรณ นี้ มี ความสอดคล องตามข อกําหนดของ กทช . Turkey Bu cihaz Türkçe karakterlerin tamamını ihtiva eden ETSI TS 123.038 V8.0.0 (veya sonraki sürümünkodu) ve ETSI TS 123.040 V8.1.0 (veya sonraki sürümün kodu) teknik özelliklerine uygundur.
ET51/56 Enterprise Tablet Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg www.zebra.com/weee voor meer informatie over het terugzenden van producten. Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji należy zwrócić do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajdują się na stronie internetowej www.zebra.com/weee.
Quick Reference Guide 23 Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin: www.zebra.com/weee. Turkish WEEE Statement of Compliance EEE Yönetmeliğine Uygundur. Software Support Zebra wants to ensure that customers have the latest release of entitled software at the time of product purchase.
O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。 X: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要 求。( 企业可在此处，根据实际情况对上表中打 “×” 的技术原因进行进一步说明。） This table was created to comply with China RoHS requirements.
