User guide

Over
IR Window
Notes
• Cameo batteries must be cycled several times
before maximum capacity is realized.
• A battery is ”cycled” by fully charging it, then
fully discharging it through normal use.
•For most consistent results, remove the
Battery Pack from the Printer when charging.
• Please refer to the “Safety Guide” included
with this product for more information on
battery and charger safety.
Zebra
®
Cameo Series
Mobile Printers
Quick Start Guide
Introduction
Thank you for choosing one of our Zebra
Cameo Series Mobile Printers. These rugged printers
will become productive and efficient additions to your
workplace thanks to their innovative design. Because
they’re made by Zebra Technologies, you can be
assured of world-class support for all of your bar code
printers, software, and supplies.
This document provides an easy reference for op-
erating and maintaining your Cameo Series Mobile
Printer. Complete documentation for this model printer
is provided by the Cameo Series User Guide available
via the Internet at: http://www.zebra.com.
Cameo models are as follows:
Model
Media
Width
Mag Card
Reader
IrDA
1
Bluetooth
1
802.11b
WLAN
1
Cameo 2 2” opt. opt. opt. N/A
Cameo 3 3” opt. opt. opt. opt.
1. Only one wireless option may be installed on a printer.
Connect With a Cable
Refer to the Label Vista™ application on the Internet at http://www.zebra.com for
help on setting up the printer.
Wireless Connection
Refer to the Wireless Quick Start Guide on the Internet at http://www.zebra.com
for help on setting up your wireless printer.
Close Media Cover
Terminal
Cameo
Series
printer
with
wireless
option
Terminal with wireless
communications ability
Pull Media
out of Printer
Note direction
media pulls off
the roll.
QSG-CM2-3-003 rev. A © ZIH Corp. 2006
Communications Port
1. Cameo Series Overview
2. Loading Media
3. Installing the Battery
Note • Batteries are shipped uncharged. Remove protective shrink-wrap and
labels from new battery packs and allow to charge completely prior to use.
4. Charging Batteries
5. Connect the Printer
6. Printer Controls
Power Light (green) Status Light (yellow)
Off On Blink Off On Blink
Cameo 2/3
(Cable)
Power Off Power On
Low Battery
Warning
Normal
Latch open
or out of
media
MCR ready
for card
swipe
Cameo 2/3
(IrDA or BT)
Power Off Power On
Low battery
Warning
Normal
Latch open
or out of
media
MCR ready
for card
swipe
Random
blinking
indicates
data
transmission
Cameo 3
(WLAN)
Power Off
Power On
Low Battery
Warning
and/or
Radio not
connected
to WLAN
Normal
Latch open
or out of
media
MCR ready
for card
swipe
Radio
connected
to WLAN*
* Connection to WLAN does not guarantee communications are enabled. Passwords
and/or other network settings must also be correct.
1. Magnetic Card Reader (MCR) Slot
2. Printhead
3. Gap Sensor
4. Media Edge Guide
5. Platen Roller
6. Media Cover
7. Battery Charging Receptacle
8. Communications Port
9. Control Panel
10. Belt Clip
11. Battery
6
7
5
3
1
8
4
2
10
Rotate Belt Clip
out of the
Insert this end
of the Battery
Pack into the
printer
Rotate the Battery
Pack into the Printer
until the latch clicks
into place.
Power Light
See Table
Feed Button
Press to advance the media
one blank label or a software
determined length of journal
media.
CAMEO 2 W/ MAG CARD READER
CAMEO 3 W/ MAG CARD
READER
INSTALLING THE CAMEO 2
BATTE RY
INSTALLING THE CAMEO 3
BATTE RY
Press the Battery
Pack into the
Printer until the
latch clicks
into place.
Status Light:
See table
Adjust Edge
Guide for width
of media
UCN-72
Single
Charger
Charger Jack
Communications Cable to
Terminal
Refer to “Connection Cables for
Encore, Cameo & Bravo Printers.xcl”
at http://www.zebra.com.
Insert the tabs on the
Battery Pack into the
Printer.
11
1
9
Power Button
Press to turn unit on.
Press again to turn unit off