User guide
Table Of Contents
- Contents
- About This Document
- Introduction
- Installation
- Getting Started
- Before You Begin
- Printing a Configuration Label — External ZebraNet 10/100 Print Server
- Printing a Network Configuration Label — Internal ZebraNet 10/100 Print Server and Wireless Print Servers
- Configuration of Wireless Securities
- View Wireless Status through the Control Panel
- Determining the Active Print Server
- Assigning an IP Address on any Print Server
- Setting and Monitoring Alerts on any Print Server
- .
- Checking Print Server Configuration Settings
- Enabling Protocols
- Defaulting ALL Print Servers
- Using WebView
- Using ZebraNet Bridge
- Using a ZPL Command
- Defaulting the ZebraNet 10/100 Print Server on the 105SL, S4M, PAX4 and External Devices
- Defaulting the Wireless Print Server on the S4M
- Defaulting the Print Servers on the ZM400 and ZM600 Printers
- Defaulting the Print Servers on the ZP Series, LP/TLP 2824 Plus, and G-Series Printers
- Defaulting the Print Servers on the HC100 Printers
- Defaulting the Print Servers on the 105SL, PAX4, Xi4, and ZE500 Printers
- Defaulting the Print Servers on the ZT210 and ZT220 Printers
- Defaulting the Print Servers on the ZT230 Printers
- Printing Queues
- Using Printing Protocols
- ZebraLink WebView
- Print Server Web Pages
- Control Panel
- Hardware Troubleshooting
- Troubleshooting the External 10/100 Print Server
- Troubleshooting the Internal ZebraNet 10/100 Print Server
- Troubleshooting the Wireless Print Server
- ZebraNet Bridge Discovery or Configuration Problems
- Unable to Print
- Unable to Configure Device
- HP JetAdmin or HP Web JetAdmin
- Wireless Error Messages
- General Wireless Issues
- Encryption and Authentication Issues
- IP Issues
- Frequently Asked Questions
- Glossary
- Index
Index
158
P1043301-002 02/28/2012
troubleshooting (cont’d.)
reset internal wired print server to factory defaults
133
reset wireless print server to factory defaults
135
system disabled after encryption set
141
unable to configure device
138
unable to print
136
using telnet
137
WEP key field not large enough
141
wireless error messages
138
wireless print server
135
wireless radio card not acknowledged
139
WPA mode
141
U
unable to configure device
troubleshooting
138
upgrade
firmware
32
user ID
default
41
V
view
directory listing
103
port status of print server
119
printer configuration
90
printer controls
108
view and modify printer settings
advanced setup
97
calibration
96
general setup
93
media setup
96
network communications setup
94
print listings on label
94
RFID setup
95
serial communications setup
93
WebView
91
ZPL control
97
W
web admin settings
print server configuration menu
116
web pages
problems accessing with wired IP address
142
WebView
88
advanced setup
97
calibration
96
check configuration settings
67
default print servers to factory settings
73
directory listing
103
enabled protocols
70
general setup
93
home page
88
media setup
96
network communications setup
94
network configuration screens
98
primary/secondary settings
99
print listing on label
94
print server features
110
print server status
118
printer configuration
90
printer controls
108
reset print server
120
restore print server
121
RFID setup
95
serial communications setup
93
setting alerts
64
SMTP settings
100
SNMP settings
99
TCP/IP settings for X60.15.x and ZSPx
100
TCP/IP settings for Xi4 Series, ZM Series, RZ
Series
101
view and modify printer settings
91
view printer configuration settings
90
view printer controls
108
wireless encryption setup settings
102
wireless setup settings
102
ZPL control
97
wired and wireless print servers
both installed
55
wired print server
check during bootup
56
printer requirements
22
wired print servers
supported services
16
wireless encryption setup settings
WebView
102
wireless error messages
troubleshooting
138