User guide
Table Of Contents
- Contents
- About This Document
- Introduction
- Installation
- Getting Started
- Before You Begin
- Printing a Configuration Label — External ZebraNet 10/100 Print Server
- Printing a Network Configuration Label — Internal ZebraNet 10/100 Print Server and Wireless Print Servers
- Configuration of Wireless Securities
- View Wireless Status through the Control Panel
- Determining the Active Print Server
- Assigning an IP Address on any Print Server
- Setting and Monitoring Alerts on any Print Server
- .
- Checking Print Server Configuration Settings
- Enabling Protocols
- Defaulting ALL Print Servers
- Using WebView
- Using ZebraNet Bridge
- Using a ZPL Command
- Defaulting the ZebraNet 10/100 Print Server on the 105SL, S4M, PAX4 and External Devices
- Defaulting the Wireless Print Server on the S4M
- Defaulting the Print Servers on the ZM400 and ZM600 Printers
- Defaulting the Print Servers on the ZP Series, LP/TLP 2824 Plus, and G-Series Printers
- Defaulting the Print Servers on the HC100 Printers
- Defaulting the Print Servers on the 105SL, PAX4, Xi4, and ZE500 Printers
- Defaulting the Print Servers on the ZT210 and ZT220 Printers
- Defaulting the Print Servers on the ZT230 Printers
- Printing Queues
- Using Printing Protocols
- ZebraLink WebView
- Print Server Web Pages
- Control Panel
- Hardware Troubleshooting
- Troubleshooting the External 10/100 Print Server
- Troubleshooting the Internal ZebraNet 10/100 Print Server
- Troubleshooting the Wireless Print Server
- ZebraNet Bridge Discovery or Configuration Problems
- Unable to Print
- Unable to Configure Device
- HP JetAdmin or HP Web JetAdmin
- Wireless Error Messages
- General Wireless Issues
- Encryption and Authentication Issues
- IP Issues
- Frequently Asked Questions
- Glossary
- Index
157
Index
02/28/2012 P1043301-002
reset internal wired print server to factory defaults
troubleshooting
133
reset wireless print server to factory defaults
troubleshooting
135
restore
print server
121
RFID setup
WebView
95
ribbon
ordering
10
S
sales 10
security type
wireless radio cards
18
serial communications setup
WebView
93
serial number
configuration label
43
set and monitor alerts
using WebView
64
using ZebraNet Bridge
63
signal strength and quality
indicators
51
simultaneous print servers
active device selection
56
SMTP settings
print server configuration menu
116
WebView
100
SNMP settings
print server configuration menu
115
WebView
99
specifications
external ZebraNet 10/100 Print Server
28
internal ZebraNet 10/100 Print Server
29
wireless print server
30
static route
assign an IP address
60
status and configuration
print server
110
subnet mask
configuration label
43, 46
support
16
address administration protocols
16
supported services
wired print servers
16
supported wireless radio cards
17
System V queue
configuration
81
prerequisites
81
UNIX configuration
81
T
TCP/IP configuration
print server configuration menu
114
TCP/IP logical printing ports
print server configuration menu
115
TCP/IP settings for X60.15.x and ZSPx
WebView
100
TCP/IP settings for Xi4 Series, ZM Series, RZ Series
WebView
101
technical support
10
telnet
troubleshooting
137
troubleshooting
000.000.000.000 as IP address
142
configuration problems
136
connection problems after firmware upgrade
139
discovery problems
136
encryption and authentication issues
141
general wireless issues
139
HP Web JetAdmin
138
inconsistent wireless connection
140
IP address
142
IP issues
142
Kerberos
141
network status/activity indicator for the external
10/100 print server
130
network status/activity indicator for the internal 10/
100 print server
133
NO CARD INSERTED message 138
no home page
142
NOT ASSOCIATED message 138
NOT AUTHENTICATD message 138
not connecting to wireless network
139
ping the printer
136
poor signal strength
138
print a configuration label using ZPL command
137
printer won’t connect to WLAN
141
RADIO WARNING POOR SIGNAL message
138
reset external wired print server to factory defaults
130