User guide
Table Of Contents
- Contents
- About This Document
- Introduction
- Installation
- Getting Started
- Before You Begin
- Printing a Configuration Label — External ZebraNet 10/100 Print Server
- Printing a Network Configuration Label — Internal ZebraNet 10/100 Print Server and Wireless Print Servers
- Configuration of Wireless Securities
- View Wireless Status through the Control Panel
- Determining the Active Print Server
- Assigning an IP Address on any Print Server
- Setting and Monitoring Alerts on any Print Server
- .
- Checking Print Server Configuration Settings
- Enabling Protocols
- Defaulting ALL Print Servers
- Using WebView
- Using ZebraNet Bridge
- Using a ZPL Command
- Defaulting the ZebraNet 10/100 Print Server on the 105SL, S4M, PAX4 and External Devices
- Defaulting the Wireless Print Server on the S4M
- Defaulting the Print Servers on the ZM400 and ZM600 Printers
- Defaulting the Print Servers on the ZP Series, LP/TLP 2824 Plus, and G-Series Printers
- Defaulting the Print Servers on the HC100 Printers
- Defaulting the Print Servers on the 105SL, PAX4, Xi4, and ZE500 Printers
- Defaulting the Print Servers on the ZT210 and ZT220 Printers
- Defaulting the Print Servers on the ZT230 Printers
- Printing Queues
- Using Printing Protocols
- ZebraLink WebView
- Print Server Web Pages
- Control Panel
- Hardware Troubleshooting
- Troubleshooting the External 10/100 Print Server
- Troubleshooting the Internal ZebraNet 10/100 Print Server
- Troubleshooting the Wireless Print Server
- ZebraNet Bridge Discovery or Configuration Problems
- Unable to Print
- Unable to Configure Device
- HP JetAdmin or HP Web JetAdmin
- Wireless Error Messages
- General Wireless Issues
- Encryption and Authentication Issues
- IP Issues
- Frequently Asked Questions
- Glossary
- Index
Index
156
P1043301-002 02/28/2012
no printer home page
troubleshooting
142
noise level indicator
51
NOT ASSOCIATED message 138
NOT AUTHENTICATD message 138
O
onboard flash 105
ordering ribbon and media
10
output port configuration
print server configuration menu
117
overview
16
P
password
default
41
ping the printer
troubleshooting
136
poor signal strength
138
POP3 email printing
print server configuration menu
117
prerequisites
System V queue
81
primary network device
preference for active print server
56
primary/secondary settings
WebView
99
print
configuration label for an internal wired print
server
44
configuration label for external wired print server
42
print a configuration label for an internal wired print
server
minimum label widths
44
print a configuration label for external wired print
server
minimum label widths
42
print listing on label
WebView
94
print problems
troubleshooting
136
print protocol
84
FTP
85
print queue configuration
Berkeley Software Distribution (BSD)-Style
80
print server
reset
120
restore
121
status and configuration
110
to view port status
119
print server configuration menu
enabled protocols
113
output port configuration
117
POP3 email printing
117
SMTP email alert configuration
116
SNMP settings
115
TCP/IP configuration
114
TCP/IP logical printing ports
115
web admin settings
116
print server configuration settings
to check
66
print server features
WebView
110
print server status
to open configuration page
118
WebView
118
print servers
default to factory settings
73
printer configuration
to view settings
90
WebView
90
printer controls
view
108
WebView
108
printer memory
105
protocols
enable
70
enabled using WebView
70
print server configuration menu
113
Q
queue configuration
BSD-Style
80
System V
81
R
RADIO WARNING POOR SIGNAL message 138
related documents
13
requirements
browser support
16
wired print servers
22
wireless print servers
23
requirements for wired print servers
firmware
25
requirements for wireless print servers
firmware
27
reset
print server
120
reset external wired print server to factory defaults
troubleshooting
130