Zebra® P120i™ Card Printer User’s Manual
© 2005 ZIH Corp. Zebra®, Stripe®, ZPL®, ZebraNet®, ZebraLink®, and ZPL II® are registered trademarks of Zebra Technologies. The copyrights in this manual and the printer described therein are owned by Zebra Technologies. Unauthorized reproduction of this manual or the software in the printer may result in imprisonment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.
Foreword This manual contains installation and operation information for the Zebra P120i card printers manufactured by Zebra Technologies Corporation. Copyright Notice This document contains information proprietary to Zebra Technologies Corporation. This document and the information contained within is Copyrighted by Zebra Technologies Corporation and may not be duplicated in full or in part by any person without written approval from Zebra Technologies Corporation.
Foreword Warranty Information Warranty Information Note • Products returned must be packaged in the original or comparable packing and shipping container. In the event equipment is not so packaged, or if shipping damage is evident, it will not be accepted for service under warranty. Surface Transportation charges for return to customers in the continental United States is paid by Zebra.
Foreword Return Materials Authorization Return Materials Authorization Before returning any equipment to Zebra Technologies Corporation for in-warranty or out-of-warranty repair, contact Repair Administration for a Return Materials Authorization (RMA) number. Repack the equipment in the original packing material and mark the RMA number clearly on the outside.
Foreword Return Materials Authorization Declarations of Conformity EMC Directive 89/336/EEC modified by 73/23/EEC modified by 93/68/EEC 1999/5/CE RF Emissions control EMC Directive EN 301489-3 V1.4.1 RF Emissions and Immunity for radio equipment EMC Directive EN55024 (2001) Immunity to Electro-Magnetic Disturbances EN 60950-1 (2001) Product safety 92/31/EEC and 93/68/EEC EN 55022 (1998) Low voltage Directive R&TTE Directive EN300330-2 V1.1.
Foreword Return Materials Authorization Industry Canada Notice This device complies with Industry Canada ICS-003 class B requirements. P120i Printer Model The Zebra Product Number tells a story: Here is a quick review of the Zebra Card Printer Series numbering and lettering system to help you.
Foreword Return Materials Authorization Icons Throughout this manual, different icons highlight important information, as follows: Note • Indicates information that emphasizes or supplements important points of the main text. Important • Advises you of information that is essential to complete a task, or points out the importance of specific information in the text. Electric Shock Caution • Warns you of a potential electric shock situation.
Contents • Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Copyright Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 3 • P120i Printer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Printer Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading Ribbon Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Getting Started Unpacking Your Card Printer Your P120i printer ships in a cardboard carton, protected by styrofoam inserts and a protective anti-static bag. Keep all packaging material in case you need to move or re-ship the printer. 1. Before opening and unpacking the printer, inspect the carton to ensure that no damage occurred during shipment. 2. Ensure that you have a clean and nearly dust free environment for proper operation and storage of the printer. 3.
Getting Started Controls and Indicators 4. Lift the printer out of the carton by holding it on both sides of the bottom and lifting the printer gently from the carton. 5. Remove the box containing the printer accessories from the shipping carton. 6. Make sure the following accessories are included with your P120i printer: a. Software CD-ROM b. Quick Start Guide c. Cleaning Kit d. 120 vac and 230 vac Power Cords e. Power Transformer f.
Getting Started Controls and Indicators POWER SOCKET 980540-01-04 POWER SWITCH USB PORT USB Port The USB port is located at the rear of the printer unit, bottom left. Multi-Function LCD Panel MULTI-FUNCTION LCD PANEL 980504-01-03 MULTI-FUNCTION CONTROL BUTTON The LCD Panel can display the following messages: Mode Message Operational 980504-001 Rev.
Getting Started Controls and Indicators Mode Message PRINTING MONO Fixed MAG ENCODING Fixed PRINTING CYAN Fixed PRINTING YELLOW Fixed PRINTING MAGENTA Fixed PRINTING BLACK Fixed PRINTING OVERLAY Fixed DOWNLOADING FW Fixed CLEANING PRINTER Fixed Warnings CLEAN PRINTER Fixed REMOVE RIBBON THEN CLOSE LID Scrolling INSERT FEEDER CLEANING CARD Scrolling REMOVE FEEDER CARD Scrolling PRESS BUTTON TO CONTINUE Scrolling FEED LONG CLEANING CARD IN EXIT Scrolling CLEANING PRINTER Scro
2 Printer Installation Installing the P120i Printer Caution • Do not power the printer with USB attached to your computer at this time. The driver will prompt you when it is time to plug in and power up your printer. To install the P120i Printer on Windows 2000 and Windows XP operating systems, insert the User Documentation, Drivers, and Training CD, included with your printer, into your computer and InstallWizard will walk you through the required installation steps.
Printer Installation Installing the P120i Printer Print Driver Installation Install the P120i Printer driver as follows: 1. Insert the P120i User Documentation, Drivers, and Training CD into the CD drive of the host computer. The Select Language window will open. 2. From the Select Language window, choose the appropriate language for your system. The Main Menu will open in the selected language. 3. From the Main Menu, select Install Printer Driver. 6 P120i Card Printer User Guide 980504-001 Rev.
Printer Installation Installing the P120i Printer 4. The InstallShield Wizard will be installed and a progress window will be displayed. Once the InstalShield Wizard has been installed, the Welcome to InstallShield Wizard window will open. 5. On the Welcome to InstallShield Wizard window, click the Next button. The Select Features window will open. 980504-001 Rev.
Printer Installation Installing the P120i Printer Important • Important • Installation of ethernet printer drivers will also allow the printer to be connected via USB. 6. From the Select Features window: a. If this printer is to be a stand alone unit, click the Install USB printer drivers button. The License Agreement window will open. Proceed to USB Installation. b. To use this printer with an external print server, ethernet printer drivers are required.
Printer Installation Installing the P120i Printer USB Installation If you reject the License Agreement by clicking the No button, the installation process will terminate. 1. Accept the License Agreement by clicking the Yes button. The Select the Setup Type window will open. 2. From the Select the Setup Type window: 980504-001 Rev. A a. If you are willing to accept the default settings for your printer, select the Complete installation option, click the Next> button. Proceed to Complete Installation.
Printer Installation Installing the P120i Printer Custom Installation 1. In the Card Image Rotation window, select the rotation desired, then click the Next> button. The Print on Both Sides window will open. 2. In the Print on Both Sides window, select Yes or No, and click the Next> button. The Monochrome Conversion window will open. 10 P120i Card Printer User Guide 980504-001 Rev.
Printer Installation Installing the P120i Printer 3. In the Monochrome Conversion window, choose the conversion type required. Click the Next> button. The Network Printer Components window will open. 4. From the Network Printer Components window 980504-001 Rev. A a. Select the Install network printer components option and click the Next> button. The Default network ribbon window will open. b. Select the Do not install network printer components option and click the Next> button.
Printer Installation Installing the P120i Printer 5. In the Default network ribbon window, choose the desired default network ribbon, and click the Next> button. The Enter First IP Address window will open. 6. Enter the IP address of the first printer into the text box and click the Next button. The Enter Second IP Address window will open. 12 P120i Card Printer User Guide 980504-001 Rev.
Printer Installation Installing the P120i Printer 7. If you are installing a second network printer, enter the IP address of the second printer into the text box. If you are installing only one network printer, leave text box blank. Click the Next button. The Enter Third IP Address window will open. 8. If you are installing a third network printer, enter the IP address of the third printer into the text box. If you are installing only one or two network printers, leave text box blank.
Printer Installation Installing the P120i Printer Encoder Settings 1. In the Encode Only window, choose Yes or No. If you choose Yes, the printer will be set up to ONLY encode magnetic stripes on cards. No printing of cards will occur. Click the Next> button. The Select Encoder Coercivity window will open. 2. In the Select Encoder Coercivity window, choose coercivity settings that match the type of cards being encoded, then click the Next> button. The Track 1 Settings window will open.
Printer Installation Installing the P120i Printer 3. In the Track 1 Settings window, select the required track settings for Track 1 and click the Next> button. The Track 1 Density window will open. 4. In the Track 1 Density window, select the density of track 1 and click the Next> button. The Track 2 Settings window will open. 980504-001 Rev.
Printer Installation Installing the P120i Printer 5. In the Track 2 Settings window, select the required track settings for Track 2 and click the Next> button. The Track 2 Density window will open. 6. In the Track 2 Density window, select the density of track 2 and click the Next> button. The Track 3 Settings window will open. 16 P120i Card Printer User Guide 980504-001 Rev.
Printer Installation Installing the P120i Printer 7. In the Track 3 Settings window, select the required track settings for Track 3 and click the Next> button. The Track 3 Density window will open. 8. In the Track 3 Density window, select the density of the track and click the Next> button. 980504-001 Rev.
Printer Installation Installing the P120i Printer 9. You will be asked if you want to apply the custom settings. a. If you select Yes, the settings you selected in the previous windows will be applied. b. If you choose No, the default settings will take effect. Whether you select Yes or No, the Select Program Folder window will open. Proceed to Complete Printer Installation.
Printer Installation Installing the P120i Printer 2. In the Card Image Rotation window, select the rotation desired, then click the Next> button. The Print on Both Sides window will open. 3. In the Print on Both Sides window, select Yes or No, and click the Next> button. The Monochrome Conversion window will open. 980504-001 Rev.
Printer Installation Installing the P120i Printer 4. In the Monochrome Conversion window, choose the conversion type required. Click the Next> button. The Default network ribbon window will open 5. In the Default network ribbon window, choose the desired default network ribbon, and click the Next> button. The Enter First IP Address window will open. 20 P120i Card Printer User Guide 980504-001 Rev.
Printer Installation Installing the P120i Printer 6. Enter the IP address of the first printer into the text box and click the Next button. The Enter Second IP Address window will open. 7. If you are installing a second network printer, enter the IP address of the second printer into the text box. If you are installing only one network printer, leave text box blank. Click the Next button. The Enter Third IP Address window will open. 980504-001 Rev.
Printer Installation Installing the P120i Printer 8. If you are installing a third network printer, enter the IP address of the third printer into the text box. If you are installing only one or two network printers, leave text box blank. Click the Next button. The Encode Only window will open.. 9. In the Encode Only window, choose Yes or No. If you choose Yes, the printer will be set up to ONLY encode magnetic stripes on cards. No printing of cards will occur. Click the Next> button.
Printer Installation Installing the P120i Printer 10. In the Select Encoder Coercivity window, choose coercivity settings that match the type of cards being encoded, then click the Next> button. The Track 1 Settings window will open. 11. In the Track 1 Settings window, select the required track settings for Track 1 and click the Next> button. The Track 1 Density window will open. 980504-001 Rev.
Printer Installation Installing the P120i Printer 12. In the Track 1 Density window, select the density of track 1 and click the Next> button. The Track 2 Settings window will open. 13. In the Track 2 Settings window, select the required track settings for Track 2 and click the Next> button. The Track 2 Density window will open. 24 P120i Card Printer User Guide 980504-001 Rev.
Printer Installation Installing the P120i Printer 14. In the Track 2 Density window, select the density of track 2 and click the Next> button. The Track 3 Settings window will open. 15. In the Track 3 Settings window, select the required track settings for Track 3 and click the Next> button. The Track 3 Density window will open. 980504-001 Rev.
Printer Installation Installing the P120i Printer 16. In the Track 3 Density window, select the density of the track and click the Next> button. 17. You will be asked if you want to apply the custom settings. a. If you select Yes, the settings you selected in the previous windows will be applied. b. If you choose No, the default settings will take effect. Whether you select Yes or No, the Select Program Folder window will open. Proceed to Complete Printer Installation.
Printer Installation Complete Printer Installation Complete Printer Installation 1. In the Select Program Folder window, accept the default folder for the program icons, or choose a different folder. Click the Next> button. The Setup Status window will open. 2. The Setup Status window will show the progress of the driver installation.When driver installation is complete, the Congratulations window will open. Proceed to Connect the P120i printer. 980504-001 Rev.
Printer Installation Complete Printer Installation Connect the P120i Printer The following instructions will guide you through the installation of the P120i printer. Caution • Limit electrical power supplied to the P120i Printer to 24 VDC. Limit excess current draw to 16 amps or less, using an associated circuit breaker or other such device. Never operate the printer in a location where operator, computer, or printer can get wet. Personal injury could result.
Printer Installation Complete Printer Installation Caution • Intermittent or unpredictable operation may occur from unsecured connectors. If damaged, the power cable must be replaced by an exact equivalent. The socket should always be easily accessible to power off the printer. 115 VAC 230 VAC 4. Insert the power supply plug into the power socket, attach the power cord (120VAC or 230VAC) to the power supply, then plug the power cord in to a grounded electrical socket of the proper voltage and type. 5.
6. Place the printer’s power switch in the ON ( | ) position. The Found New Hardware window will open. 7. In the Found New Hardware window, select the No, not at this time radio button, then click Next>. The Insert installation CD window will open.
Printer Installation Complete Printer Installation 8. In the Insert installation CD window, select the Install the software automatically radio button and click Next>. The Windows Logo Testing window will open. 9. In the Windows Logo Testing window, select the Continue Anyway button. The copying files progress bar will display. 980504-001 Rev.
Printer Installation Complete Printer Installation 10. If the Files Needed window opens, type in the required file location from the Congratulations window. When files have been successfully transferred, the Completing the New Hardware Found Wizard window will open. 11. Click the Finish button and driver installation will be complete and the Completing the New Hardware Found Wizard window will close. 12. On the Congratulations window, click Next>. You will be asked if you wish to open the ReadMe file 13.
Printer Installation Complete Printer Installation 14. Whether you select Yes or No, the InstallShield Wizard Complete window will open. 15. Click the Finish button to complete the installation. 980504-001 Rev.
Printer Installation Change Printer Driver Options Change Printer Driver Options You can change the default settings for the P120i Printer driver. Change the options as follows: 1. Select Start>Settings>Printers and Faxes. 2. From the Printers and Faxes list, right click the P120i USB Card Printer and select Properties from the pop-up menu.The Printer Properties window will open. 3.
Printer Installation Change Printer Driver Options 4. On the Sharing tab, you can choose to share the printer over the network, and install additional drivers to accommodate different operating systems. 5. On the Ports tab you can select which add, delete, and configure the printer ports, as well as choose which port the P120i printer is assigned. 980504-001 Rev.
Printer Installation Change Printer Driver Options 6. On the Color Management tab, you can add, remove, and change printer color profiles. 7. Use the Security tab to change permissions for the P120i printer. 36 P120i Card Printer User Guide 980504-001 Rev.
Printer Installation Change Printer Driver Options 8. On the Advanced tab, you can choose various printer properties, install different printer drivers, and change default printer settings. 9. On the Device Settings tab, you can change settings for a Magnetic Encoder and change to and from single feed mode. 10. Once the P120i printer driver options have been configured to your satisfaction, click the OK button to save your new configuration and close the Properties window. 980504-001 Rev.
3 P120i Printer Setup Printer Features The following shows the features found on your P120i Printer: PRINT HEAD CARD OUTPUT HOPPER LID 980504-03-01 CARD FEEDER CARD GUIDE RIBBON CARTRIDGE 980504-001 Rev.
P120i Printer Setup Loading Ribbon Cartridge Loading Ribbon Cartridge The P120i Printer requires approved ribbon cartridges (see Appendix C). The Resin Thermal Transfer and Dye Sublimation ribbons are specifically designed for your P120i Printer. • i Series Printers require the use of i Series ribbons for full color printing. • Each ribbon cartridge includes an integrated adhesive cleaning roller assembly that is used to clean the cards entering the printer.
P120i Printer Setup Loading Cards Loading Cards To help you load, print, and collect cards, the P120i has the following items: Card Feeder The card feeder is used for loading cards, it can hold up to 100 cards of 30 mils thickness. The card feeder is located under the card feeder cover of the P120i printer. Caution • DO NOT bend cards or touch print surfaces as this can reduce print quality. Note • The surface of the cards must remain clean and dust free. Always store cards in an enclosed container.
P120i Printer Setup Loading Cards 4. Holding the card deck by the sides, hold it vertically against a flat surface such as a desktop. If the deck is too thick for your hand to hold it comfortably, use about half a deck at a time. 5. Push the stack back and forth to an angle of about 45° from vertical, so as to separate all of the cards. 6. Restore the card stack to its original squared-off condition, and place the cards in the input hopper. 7.
P120i Printer Setup Printing a Test Card Card Output Hopper 1. Raise the printer lid and pull the output hopper down to place it in its functional position. 2. When not using the printer, place the card output hopper back in its closed position to protect the printer from dust. CARD OUTPUT HOPPER 980504-03-04 Printing a Test Card With ribbon cartridge and cards loaded, your P120i printer is ready to print. To check the operation of the printer, you should print a test card. 1.
4 P120i Printer Operation Printing Printing with the P120i Printer requires the Windows Printer Driver, your card design/issuing software or printer command level programming through the printer interface. The P120i Card Printer can be used with any Windows 2000, or Windows XP software application program, using the drivers provided on CD with the printer. Reference Chapter 2 for instructions on installing the P120i printer driver.
P120i Printer Operation Printing 980504-05-01 http://www.zebracard.com Printing a Sample Card Once you completed creating your sample card, you are ready to print. Ensure your printer has a True ColoursTM Card Printer Ribbon Cartridge installed and there is card stock in the card feeder. Reference Chapter 3 for instructions on installing the ribbon and loading the cards Print your sample card as follows:. 1. Select File>Print to open the Print dialogue box.
P120i Printer Operation Printing 2. Click the OK button. 3. The printer will feed in a card and start printing. The data download time will vary depending on the complexity of the card design and the processing speed of the computer. 4. Once the printing is completed, the card is ejected from the printer into the printed card hopper. 5. Remove the sample card from the card output hopper and check for any discrepancies. If the sample card is correct, your P120i card printer is to produce more cards.
5 Cleaning Cleaning System Caution • PROTECT YOUR FACTORY WARRANTY! The recommended maintenance procedures must be performed to maintain your factory warranty. Other than the recommended cleaning procedures described in this manual, allow only Zebra authorized technicians to service the P120i Printer. •NEVER loosen, tighten, adjust, or bend, etc. a part or cable inside the printer. •NEVER use a high pressure air compressor to remove particles in the printer.
Cleaning Cleaning System FEEDER CLEANING CARD CARD FEEDER PRINTER PATH CLEANING CARD COVER MULTI-FUNCTION LCD PANEL MULTI-FUNCTION CONTROL BUTTON 5. If the lid is opened and closed without removing the ribbon, the REMOVE RIBBON THEN CLOSE LID message will remain. 6. Once the cover is closed, the firmware will eject any card inside the printer. The message EJECTING CARD will display. 7. The LCD will then display FEED LONG CLEANING CARD IN EXIT.
Cleaning Cleaning the Print Head Cleaning the Print Head Use of the cleaning cards will normally do an adequate job of cleaning the printer. However, a separate Print head cleaning, using swabs, can remove more stubborn deposits when print anomalies persist. To avoid deposits, only use foam-tipped swabs. Caution • Never use a sharp object to scrape deposits from the print head. Permanent damage to the print head will result 1. Place the printer power switch in the OFF (0) position. 2.
6 Troubleshooting Troubleshooting Procedures This section offers solutions to potential problems you may experience with your P120i printer. Print Quality Issues This section will help you resolve print quality problems The print quality is dependent on several factors. The two most important factors that will increase your print quality are cleanliness and card stock.
Troubleshooting Troubleshooting Procedures Example • There are non-printing horizontal lines (white) on the card surfaces. Possible Cause: • Ribbon cartridge is not correctly positioned. Solutions: • Ensure that the ribbon is properly rolled onto the ribbon cores of the cartridge and that there are no wrinkles in the ribbon. • Replace ribbon cassette. Possible Cause: • Print Head is dirty. Solutions: • Clean the Print Head Possible Cause: • Print Head elements are damaged (e.g.
Troubleshooting Troubleshooting Procedures Possible Cause: • Ribbon cartridge may not be correctly positioned. Solution: • Check that the ribbon is properly rolled onto the ribbon cores of the cartridge, with no wrinkles. • Replace ribbon cartridge, making sure it locks in place, and print again. Possible Cause: • Ribbon may not be synchronized on the correct color panel position. Solution: • Open lid, then close lid to synchronize ribbon. Possible Cause: • Cards may not meet specifications.
7 Technical Specifications General • Integrated card feeder-and-flipper • Load-N-GoTM drop-in ribbon cartridge • 16-digit LCD display • Windows® drivers for 2000 and XP • One year printer warranty • One year (unlimited passes) printhead warranty • Color dye sublimation or monochrome thermal transfer printing • XX seconds per card full color single sided (YMCKO) • YY seconds per card full color dual-sided (YMCKOK) • 300 dpi (11.
Technical Specifications Ribbons Cartridges • Load-N-GoTM ribbon cartridge with integrated card-cleaning roller • i Series technology featuring contact-chip-based ribbon detection • YMCKO: 200 cards/cartridge • YMCKOK: 165 cards/cartridge • Monochrome: 1000 cards/cartridge in black, blue, or white • USB 1.1 (cable included) • Width: 7.9 in (201mm) • Depth: 12.9 in (328mm) • Height: 8.5 in (216mm) • Weight: 9.5 lbs (4.
Technical Specifications Card Dimensions Card Dimensions ISO standard dimensions for plain card 2.125 ± 0.002in (53.98 ± 0.050mm) 980504-07-01 Radius 0.125in (3.18mm) 3.375 ± 0.010in (85.72 ± 0.25mm) 0.009 ~ 0.034in (0.23 ~ 0.84mm) ISO standard dimensions for magnetic stripe card 0.623in (15.82mm) min 980504-07-02 0.218in (5.54mm) max MAGNETIC STRIPE 0~0.115 in (2.92 mm) 0~0.115in (2.92mm) 980504-001 Rev.
Appendix A Encoder Magnetic Card Stripe Encoder This section contains information on the additional operations of the P120i Printers with Magnetic Card Stripe Encoder. Introduction Operation and maintenance requirements for the P120i Printer with the optional magnetic card stripe encoder. The magnetic encoder can be set for either high or low coercivity. Media Loading Orientation Caution • ONLY USE cards that comply with ISO 7810 & 7811 standards for magnetic stripe cards.
Introduction MAGNETIC STRIPE 980504-AA-01 Magnetic Encoder Cleaning Use the standard cleaning card process as described in Chapter 4. This cleans the most important parts of the printer; including the print Head, Transport Roller and Magnetic Stripe Encoder.
Appendix B Card SenseTM Single Card Feed Mode Printing a Single Card Without Using the Feeder For operating the P120i card printer in single card feed mode, the printer requires that the operator install an optional Card SenseTM Single Card Feed Kit. In Single Card Feed Mode, the printer will only accept cards through the front slot, not from the card feeder. POWER SWITCH Install Card SenseTMSingle Card Feed Kit 1. Set printer to OFF. RIBBON CARTIRDGE PRINTER LID 2.
Card Sense Single Card Feed Mode Printing a Single Card Without Using the Feeder Important • Make sure the output hopper remains closed. ROLLER FROM SINGLE CARD FEED KIT BLUE TABS 3. Install the black roller from the Single Card Feed Kit into the blue tabs at the front of the printer, and press roller down firmly to lock into the tabs. Install Card Cleaning Cartridge Install the Card Cleaning Cartridge as follows: BLUE TAPE CARD CLEANING CARTRIDGE 980504-BB-03 1.
Card Sense Single Card Feed Mode Printing a Single Card Without Using the Feeder RIBBON CARTRIDGE 5. Insert the ribbon cartridge with the cleaning roller facing down, so the gears on the ends of the rollers fit into the appropriate slots. 6. Close the printer lid and push down until you hear an audible click. If you can not close the lid, the cleaning cartridge or the ribbon cartridge may be installed wrong. Setting Up the Printer Driver 1. Go to Printer Properties 2. Select the Device Settings tab 3.
Card Sense Single Card Feed Mode Printing a Single Card Printing a Single Card 980504-BB-04 1. Place the printer power switch in the ON ( | ). INSERT CARD 980504-BB-05 2. Insert a single card into the slot at the front of the printer, directly above the card output hopper. Do not feed more than one card at a time. Printer will take the card. 66 P120i Card Printer User Guide 980504-001 Rev.
Zebra Technologies Corporation 333 Corporate Woods Parkway Vernon Hills, Illinois 60061.3109 U.S.A. Telephone: +1 847.634.6700 Facsimile: +1 847.913.
