User's Manual

5/12/08 ZM™ Series/RZ™ Series User Guide 79695L-002 Rev. A
Index
A
adhesive test for ribbon coating, 35
adjustments
label left side, 91
left position, 92
media alignment for rewind, 108
print darkness, 70
printhead pressure, 61
tear-off position, 72
APL-D
set Module A storage device, 73
set Module B storage device, 74
setting compatibility mode, 73
setting control codes, 73
APL-I
adjust label left position, 91
print stored format, 82
print stored page, 81
set printer resolution, 74
status response, 87
auto calibration, 60
B
backfeed setting, 91
bar codes
list available codes, 79
battery disposal, 98
baud setting, 85
before you begin setup, 24
bitmap scaling factor, 93
black mark media
described, 34
C
calibration
media and ribbon sensor, 84
setting for head close, 90
setting for media power up, 90
troubleshooting problems, 118
Canadian DOC compliance, 4
CANCEL button
CANCEL self test, 124
description, 19
checklist
before you begin, 24
troubleshooting, 110
cleaning
cutter module, 104
exterior of printer, 99
media compartment and sensors, 103
printhead and platen roller, 100
recommended cleaning schedule, 99
communication interfaces, 27
communications diagnostics test
overview, 130
selecting, 88
communications problems, 119
components of printer, 17
configuration
changing parameters, 69
enter Setup mode, 64
exit Setup mode, 65
software or printer driver, 69
configuration label
printing using CANCEL self test, 124
printing using List Setup command, 80
Index
142
79695L-002 Rev. A ZM™ Series/RZ™ Series User Guide 5/12/08
connect printer to computer or network, 28
connect to power source, 31
contacts, 11
continuous media
described, 34
setting media type, 74
control panel
buttons described, 19
enter Setup mode, 64
exit Setup mode, 65
LCD error messages, 111
lights described, 20
location, 16
overview and illustration, 18
parameters, 69
control prefix setting, 88
counters, 79
customer service, 11
cutter
cleaning, 104
Cutter Jam
message, 114
Cutter mode media path, 40
loading media for Cutter mode, 41
print mode use described, 38
selecting Cutter mode, 73
D
darkness setting, 70
data bits setting, 86
data cables, 28
data source
connections, 27
site selection, 26
date setting, 94
default password, 66
defragmenting message, 114
Delayed Cut mode
loading media, 41
media path, 40
print mode use described, 38
selecting, 73
delimiter character setting, 89
diagnostics, 123
direct thermal mode
media scratch test, 35
setting, 75
disable password protection, 66
display language
changing from unreadable language, 121
selection, 95
disposal of printer parts, 98
download firmware, 21
dpi format conversion, 93
E
electronics cover, 16
Eltron Programming Language (EPL), 21
emulations, 21
enter Setup mode, 64
error messages, 111
Ethernet
characteristics of internal wired connection, 27
characteristics of wireless connection, 27
internal wired connection and configuration, 30
wired and wireless connector locations, 16
wireless connection and configuration, 30
exit Setup mode, 65
external view of printer, 16
F
factory defaults
reload parameters, 65
restore network settings, 65
fanfold media
described, 34
loading, 42
FCC compliance, 4
FEED button
description, 19
FEED and PAUSE self test, 129
FEED self test, 126
firmware, 21
Flash memory, 83
font list, 79
format convert setting, 93
format list, 80
format memory card, 82
format prefix setting, 88
G
general specifications, 134