User's Manual

73
Configuration
Control Panel Parameters
5/12/08 ZM™ Series/RZ™ Series User Guide 79695L-002 Rev. A
Select Print Mode
This parameter tells the printer how printed labels will be removed. Make
sure that you select a print mode that is compatible with your printer and
printer options. For information about how the print modes work with
different printer options, see Print Modes and Printer Options on page 38.
Default Value: TEAR-OFF
Selections: TEAR-OFF, PEEL-OFF, CUTTER, DELAYED CUT,
LINERLESS-P, LINERLESS-R, LINERLESS-T, REWIND
Note • The linerless selections apply only to printers that have the
Linerless option.
To change the value shown:
1. Press SELECT to select the parameter.
2. Press
PLUS (+) or MINUS (-) to scroll through the options.
3. Press
SELECT to accept any changes and deselect the parameter.
APL-D only
Set APL-D Compatibility Mode
Sets compatibility with DPL printers.
Default Value: OFF
Selections: ON, OFF
To change the value shown:
1. Press SELECT to select the parameter.
2. Press
PLUS (+) or MINUS (-) to scroll through the options.
3. Press
SELECT to accept any changes and deselect the parameter.
APL-D only
Set APL-D Control Codes
Default Value: STANDARD
Selections: STANDARD, MAINFRAME
To change the value shown:
1. Press SELECT to select the parameter.
2. Press
PLUS (+) or MINUS (-) to scroll through the options.
3. Press
SELECT to accept any changes and deselect the parameter.
APL-D only
Set Module A Storage Device for APL-D
Default Value: NONE
Selections: NONE, RAM 1, RAM 2, FLASH 1, FLASH 2
To change the value shown:
1. Press SELECT to select the parameter.
2. Press
PLUS (+) or MINUS (-) to scroll through the options.
3. Press
SELECT to accept any changes and deselect the parameter.
Table 12 • Printer Parameters (Page 4 of 26)
Parameter
Action/Explanation
Configuration
Control Panel Parameters
74
79695L-002 Rev. A ZM™ Series/RZ™ Series User Guide 5/12/08
APL-D only
Set Module B Storage Device for APL-D
Default Value: NONE
Selections: NONE, RAM 1, RAM 2, FLASH 1, FLASH 2
To change the value shown:
1. Press SELECT to select the parameter.
2. Press
PLUS (+) or MINUS (-) to scroll through the options.
3. Press
SELECT to accept any changes and deselect the parameter.
APL-I only
Set Printer Resolution for APL-I
Sets the dot size for backward compatibility with some older APL-I
printers.
Default Value: 5 MIL
Selections: 5 MIL, 10 MIL, 15 MIL
To change the value shown:
1. Press SELECT to select the parameter.
2. Press
PLUS (+) or MINUS (-) to scroll through the options.
3. Press
SELECT to accept any changes and deselect the parameter.
Set Media Type
This parameter tells the printer the type of media that you are using (see
Types of Media on page 33 for more information). Selecting continuous
media requires that you include a label length instruction in your label
format (
^LLxxxx if you are using ZPL or ZPL II).
When non-continuous media is selected, the printer feeds media to
calculate label length (the distance between two recognized registration
points of the inter-label gap, webbing, or alignment notch or hole).
Default Value: GAP/NOTCH
Selections: GAP/NOTCH, MARK, CONTINUOUS
To change the value shown:
1. Press SELECT to select the parameter.
2. Press
PLUS (+) or MINUS (-) to scroll through the options.
3. Press
SELECT to accept any changes and deselect the parameter.
Table 12 • Printer Parameters (Page 5 of 26)
Parameter
Action/Explanation