User's Manual

Introduction
The TW-5xx Series Wired/Wireless WallPlate is designed for multi-tenant buildings
such as hotels, healthcare facilities, apartments, and dormitory housing. The
TW-5xx is designed to leverage the in-building telephone wiring to deploy Ethernet
and wireless LAN networks without the effort and expense of re-wiring with
structured cabling.
This installation guide applies to TS-524 (P/N TS-0524-WR),
TW-522 (P/N TW-0522-67030-US, -EU, -WR),
TW-511 (P/N TW-0511-60010-US, -EU, -WR), and TW-510 (P/N TW-0510-WR).
Document Conventions
The following graphical alerts are in this document to indicate notable situations:
NOTE Tips, hints, or special requirements that you should take note of.
CAUTION Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING! Indicates a condition or procedure that could result in
personal injury or equipment damage.
Warnings
• This equipment should only be installed by qualified professional installers.
• Read all installation instructions and site survey reports, and verify correct equipment
installation before installing this equipment.
• Remove jewelry and watches before installing this equipment.
• Verify proper wiring and grounding for each installation location .
• Verify there is adequate ventilation around the device, and that ambient temperatures meet
equipment operation specifications
(0° to 40°C / 32° to 104°F except TW-522 which is 0° to 35°C / 32° to 95°F).
TS-524 and TW-5xx Specifications
*
*Operating frequencies and transmit power settings depend on national regulatory limits.
Wireless Interface TW-511: Single radio; 802.11a/b/g/n; 2.4GHz or 5GHz
TW-522: Dual radio; 802.11a/b/g/n/ac; 2.4GHz and 5GHz
LAN Ethernet port 2 x IEEE 802.3 10/100MB auto-sensing via RJ45
Uplink UTP 1 x VDSL2 via RJ11
Pass through phone port Filtered RJ11 port
Medium DSSS, OFDM, MIMO
Network Standards 802.11a/b/g/n, 802.11i, 802.11-2007,
802.11ac (TW-522 only)
Data rates 802.11b: 1, 2, 5.5, 11Mbps
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11a: 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11n: MCS 0-15, up to 300Mbps
802.11ac: MCS 0-9, up to 400Mbps (TW-522 only)
Operating frequencies
* 2.4GHz: 2400 to 2483.5MHz
5GHz: 5150 to 5250MHz, 5725 to 5850MHz
Transmit power settings
* 1 to 20dBm in 1dBm increments
Antenna configuration
Two internal omni-directional, 1x2 or 2x2 MIMO operation
4dBi peak @ 2.4GHz, 5dBi @ 5GHz
TS-524 VLANs 802.1 Q tagged VLANs, access or trunk
TS-524 Management Telnet, SSH, HTTPS, or serial console
TS-524 Uplink ports 2 x IEEE 802.3 10/100/1000MB auto-sensing via RJ45
TS-524 UTP ports 1 x RJ21 for PBX connection, 1 x RJ21 for downstream VDSL2
Zebra Technologies Corporation
Lincolnshire, IL 60069 USA
TS-524 Switch and TW-5xx WallPlate
Installation Guide
MN001390A01
October 2015 Revision C
(2)
(1)
(3) (4) (5) (6)
Installing In-line Filters
The TW-5xx Wallplate features a built-in Plain Old Telephone Setvice (POTS) and Line Power
filter for the desk phone. Install an in-line filter on all other phone jacks that will have a phone
connected.
The terminated filter has a clipped RJ11 connector. This is purposely done to comply with
EN60950 requirements. Use a small flat blade screwdriver to lift the tab if attempting to
remove the filter.
If installing a filter on a bathroom phone, use the unterminated filter. Remove the bathroom
wall plate and terminate the filter in the wall box using wire beans.
Installing the TW
-5xx WallPlate
1. Loosen the screws on the existing wall plate to create a gap of 6mm (1/4 in).
2. Attach the mounting adapter using the keyhole slots.
3. Tighten the screws until the mounting adapter is securely attached.
CAUTION Do not over tighten.
4. Connect the supplied 10cm cable between the TW-5xx bottom mounted RJ11
jack and the existing RJ11 jack.
5. Hook the bottom tabs on the mounting adapter to the TW-5xx. Rotate and
snap the TW-5xx onto the adapter.
Network Configuration (TS-524)
The following will enable all ports and configure one wireless LAN:
Log in to the system using Telnet, SSH, HTTP, or Serial Console using the default
username and password:
Username: admin
Password: admin123
Enter the following commands:
config
password admin <enter your new password>
country-code <xx = your country>
hostname <enter your hostname>
interface vlan1 ip-address 192.168.1.1/24
wlan Guest
exit
int dsl1-24 no shutdown
int radio1-24.1
channel 6
power 18
wlan Guest
no shutdown
exit
Enabling Line Power
Line power should be enabled after the filters and TW-5xx WallPlate have been
installed. Line power is safe for use with telephony equipment but it will ring the
phones if the filters are not installed first.
To enable line power, enter the following commands into the CLI:
interface dsl1-24 line-power
write memory
Regulatory Information
This guide applies to Model Numbers: TS-524, TW-510, TW-511, and TW-522.
All Zebra devices are designed to be compliant with rules and regulations in locations where they are sold
and will be labeled as required.
Local language translations are available at the following website:
www.zebra.com/support
.
Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user's
authority to operate the equipment. When Zebra devices are professionally installed, the Radio Frequency
Output Power will not exceed the maximum allowable limit for the country of operation.
Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas,
modifications, or attachments could cause damage and may violate regulations.
Radio Modules
The TW-511 contains an approved radio module. This module is identified below:
802.11 a/b/g/n WLAN, Type: TW-5
Wireless Device Country Approvals (TW-511 and TW-522 Only)
Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved
for use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe.
Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at
www.zebra.com/doc
.
Note: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg,
Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden,
Switzerland and the United Kingdom.
Operation of the device without regulatory approval is illegal.
Country Selection
Select only the country in which you are using the device. Any other selection will make the operation of this
device illegal. The US version of the Access Point will operate only if US country code is selected. The US
version will be sold / used in the US protectorates: American Samoa, Guam, Northern Marianas, Puerto Rico,
US Virgin Islands.
Serial Console Connection Default IP Address
Speed: 19200
Data Bits: 8
Parity: None
Stop Bit: 1
Flow Control: None
192.168.1.3