RFS4000_Baseline.
RFS4000_Baseline.book Page 2 Tuesday, September 28, 2010 9:55 AM MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Symbol is a registered trademark of Symbol Technologies, Inc. All other product or service names are the property of their respective owners. © Motorola, Inc. 2010. All rights reserved.
RFS4000_Baseline.book Page 3 Tuesday, September 28, 2010 9:55 AM Contents 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.0 LED Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4.0 Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.0 Quick Start Information . . . . .
RFS4000_Baseline.
RFS4000_Baseline.book Page 1 Tuesday, September 28, 2010 9:55 AM Introduction 1 Introduction The Motorola RFS4011 Series Integrated Services Controller is a member of Motorola’s RFS Series Integrated Services Controller family. The RFS4011 provides centralized Wireless LAN (WLAN) configuration and management by coalescing a network “intelligence” previously spread across physically distributed access points. The RFS4011 simplifies deployment of a Wired/Wireless 802.11 a/b/g/n network, for a SME/SMB.
RFS4000_Baseline.book Page 2 Tuesday, September 28, 2010 9:55 AM 2 RFS4011 Series Integrated Services Controller: Installation Guide ! CAUTION WARNING! Care is required. Disregarding a caution can result in data loss or equipment malfunction. Indicates a condition or procedure that could result in personal injury or equipment damage. 1.
RFS4000_Baseline.book Page 3 Tuesday, September 28, 2010 9:55 AM Specifications 2 Specifications 2.1 Physical Specifications Width 304.8mm (12.0in) Height 44.45mm (1.75 in) 1 RU Depth 254mm (10.0 in) Weight 2.15 Kg (4.73 lbs) Operating Temperature Operating Humidity Operating Altitude 0°C - 40°C (32°F - 104°F) 5% - 85% RH, non-condensing 10,000 ft @ 28deg C < 15% Relative Humidity 2.
RFS4000_Baseline.book Page 4 Tuesday, September 28, 2010 9:55 AM 4 RFS4011 Series Integrated Services Controller: Installation Guide 3 LED Codes The RFS4011 Series Integrated Services Controller has eight status LEDs on its front panel. Four LEDs for the system, fan, and temperature status, and 2 each per radio to show access (per band) or sensor operation. Each of the six Gigabit Ethernet Ports have two status LEDs.
RFS4000_Baseline.book Page 5 Tuesday, September 28, 2010 9:55 AM LED Codes 3.1.
RFS4000_Baseline.book Page 6 Tuesday, September 28, 2010 9:55 AM 6 RFS4011 Series Integrated Services Controller: Installation Guide 3.1.
RFS4000_Baseline.book Page 7 Tuesday, September 28, 2010 9:55 AM LED Codes 3.1.4 Fan LED Fan LED Event Off System Off / POST Start Green Blinking POST in Process Green Solid All System Fans Normal Operation Amber Solid Redundant Cooling Failure System Operational Amber Blinking System Cooling Failure System will be held in reset until the issue is resolved 3.1.
RFS4000_Baseline.book Page 8 Tuesday, September 28, 2010 9:55 AM 8 RFS4011 Series Integrated Services Controller: Installation Guide 3.2 Radio Status LEDs RADIO 1 RADIO 2 3.2.1 Radio 1 LEDs Radio 1 LED 1 Event Off WLAN Radio Disabled or Not Installed Green Solid Radio Present but not configured (2.4GHz Band) Green Blinking Activity - Transmit / Recieve (2.
RFS4000_Baseline.book Page 9 Tuesday, September 28, 2010 9:55 AM LED Codes 3.2.2 Radio 2 LEDs Radio 2 LED 1 Event Off WLAN Radio Disabled or Not Installed Amber Solid Radio Present but not configured (5.2GHz Band) Amber Blinking Activity - Transmit / Recieve (5.
RFS4000_Baseline.book Page 10 Tuesday, September 28, 2010 9:55 AM 10 RFS4011 Series Integrated Services Controller: Installation Guide 3.
RFS4000_Baseline.book Page 11 Tuesday, September 28, 2010 9:55 AM LED Codes 3.3.1 RJ-45 Port Speed LED Port Speed LED Event Off 10 Mbps Green Solid 100 Mbps Green Blinking 1000 Mbps Amber Blinking Port Fault 3.3.2 RJ-45 Port Activity LED Port Status LED Event Off No Link or Administratively shut down Green Solid Link present Green Blinking Activity: Transmit and Receive Amber Blinking Link Fault 3.3.
RFS4000_Baseline.book Page 12 Tuesday, September 28, 2010 9:55 AM 12 RFS4011 Series Integrated Services Controller: Installation Guide 3.4 SFP Gigabit Ethernet LEDs UPLINK SFP Port speed Port activity 3.4.1 SFP Port Speed LED Port Speed LED Event Green Blinking 1000 Mbps Amber Blinking Module or Tx/Rx Fault Loss 3.4.
RFS4000_Baseline.
RFS4000_Baseline.book Page 14 Tuesday, September 28, 2010 9:55 AM 14 RFS4011 Series Integrated Services Controller: Installation Guide 4.1 Cabling Information Console connector UPLINK ExpressCard RADIO 11 1 USB port 2 RADIO Gigabit Ethernet RJ-45 connectors The RFS4011 Series Integrated Services Controller has five RJ-45 Gigabit Ethernet LAN ports, 1 combo Gigabit (RJ45 + SFP) uplink port, one USB port, one Console connector and one ExpressCard slot.
RFS4000_Baseline.book Page 15 Tuesday, September 28, 2010 9:55 AM Hardware Setup 4.2.1 Installing Gigabit Ethernet SFPs 1. Open the bail on the transceiver. Open bail to insert SFP transceiver 2. Insert the SFP transceiver into the corresponding port on the controller.
RFS4000_Baseline.book Page 16 Tuesday, September 28, 2010 9:55 AM 16 RFS4011 Series Integrated Services Controller: Installation Guide 3. Once the SFP transceivers are properly seated in their ports, close the bails to lock the transceivers in place.
RFS4000_Baseline.book Page 17 Tuesday, September 28, 2010 9:55 AM Hardware Setup 4. Insert the fiber optic cables into the installed transceivers.
RFS4000_Baseline.book Page 18 Tuesday, September 28, 2010 9:55 AM 18 RFS4011 Series Integrated Services Controller: Installation Guide 4.3 Connecting USB Devices USB port The RFS4011 contains one USB port for connecting USB flash storage devices to the controller. The controller can use the USB flash storage device for file transfers and firmware updates. Follow the setup instructions below to connect the devices to the controller and access devices through the Web UI or Command Line Interface. 1.
RFS4000_Baseline.book Page 19 Tuesday, September 28, 2010 9:55 AM Hardware Setup 4.4 Rack Mount Installation Instructions (Optional) For rack mounted installations, the RFS4011 Series Integrated Services Controller is compatible with an optional 2U rack mount bracket (Motorola Part Number: RFS-4011-MTKT2U-WR). To install the RFS4011 in a rack: 1. Attach the controller to the 2U rack mount kit using the guides provided. Power Supply Front Attach to Rack 2U Rack Mount Kit 2.
RFS4000_Baseline.book Page 20 Tuesday, September 28, 2010 9:55 AM 20 RFS4011 Series Integrated Services Controller: Installation Guide 4.5 RFS4011 Antenna Facade Installation (Optional) The RFS4011 Series Integrated Services Controller is compatible with an optional antenna facade (Motorola Part Number: ML-2452-PTA4M3X3-1) To install the RFS4011 antenna facade: 1. Align the antenna connectors on the antenna facade with the antenna connectors on the back of the RFS4011. 2.
RFS4000_Baseline.book Page 21 Tuesday, September 28, 2010 9:55 AM Hardware Setup 3. Once all six antenna connectors have been securely connected, align the two side and two rear clips on the antenna facade with the corresponding holes on the RFS4011. 4. Gently press down on the antenna facade until the clips click into place.
RFS4000_Baseline.book Page 22 Tuesday, September 28, 2010 9:55 AM 22 RFS4011 Series Integrated Services Controller: Installation Guide 4.6 RFS4011 Console Port Setup To add the RFS4011 Series Integrated Services Controller to the network and prepare it for initial configuration: 1. Using the supplied console cable, connect the RFS4011 serial port to an RS-232 (DB-9) serial port on a separate computer (the “configuration computer”).
RFS4000_Baseline.book Page 23 Tuesday, September 28, 2010 9:55 AM Hardware Setup 2. On the configuration computer, configure a terminal emulation application (such as HyperTerminal) as follows: Terminal Type Port Terminal Settings VT-100 COM port 19200bps transfer rate 8 data bits no parity 1 stop bit no flow control no hardware compression 4.7 Supplying Power to the RFS4011 Power Inlet 1. Plug the power supply (Motorola Part Number: 86-120786-01) into the power inlet at the back of the RFS4011. 2.
RFS4000_Baseline.book Page 24 Tuesday, September 28, 2010 9:55 AM 24 RFS4011 Series Integrated Services Controller: Installation Guide . WARNING! An improper shutdown can render the RFS4011 Series Integrated Services Controller inoperable such that it could require service by Motorola Support. Do not remove AC power without first following the shutdown procedure. An abrupt loss of power can corrupt the information stored on the device. 4.
RFS4000_Baseline.book Page 25 Tuesday, September 28, 2010 9:55 AM Quick Start Information 5 Quick Start Information Once the RFS4011 Series Integrated Services Controller hardware is installed and powered on, complete the following steps to get the device up and running on and access the management functions on the controller: 1. Connect one end of an Ethernet cable to any of the five LAN ports on the front of the RFS4011 and connect the other end to a computer with a working web browser. 2.
RFS4000_Baseline.book Page 26 Tuesday, September 28, 2010 9:55 AM 26 RFS4011 Series Integrated Services Controller: Installation Guide 7. If this is the first time the management interface has been accessed, a dialogue displays to start the initial setup wizard. Click the Start Wizard button to run the initial setup wizard. 8. On the first screen of the wizard, change the default Password and enter a Location, and Contact name. 9. Select a Time Zone and Country for the RFS4011. 10.
RFS4000_Baseline.book Page 27 Tuesday, September 28, 2010 9:55 AM Regulatory Information 6 Regulatory Information This guide applies to the following Model Number: RFS-4011 All Motorola devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Any changes or modifications to Motorola equipment, not expressly approved by Motorola, could void the user's authority to operate the equipment.
RFS4000_Baseline.book Page 28 Tuesday, September 28, 2010 9:55 AM 28 RFS4011 Series Integrated Services Controller: Installation Guide Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research.
RFS4000_Baseline.book Page 29 Tuesday, September 28, 2010 9:55 AM Regulatory Information Power Supply Use ONLY a LISTED Motorola, Type no. 86-120786 (54Vdc, 2.7A), direct plug-in power supply, marked Class 2 (IEC60950-1, SELV). Use of alternative Power Supply will invalidate any approvals given to this unit and may be dangerous. Laser Devices - Gigabit Ethernet SFP Option Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
RFS4000_Baseline.book Page 30 Tuesday, September 28, 2010 9:55 AM 30 RFS4011 Series Integrated Services Controller: Installation Guide Radio Frequency Interference Requirements—FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
RFS4000_Baseline.book Page 31 Tuesday, September 28, 2010 9:55 AM Regulatory Information CE Marking and European Economic Area (EEA) The use of 2.4GHz RLAN’s, for use through the EEA, have the following restrictions: • • • Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz. France outside usage, the equipment is restricted to 2.400-2.45 GHz frequency range. Italy requires a user license for outside usage.
RFS4000_Baseline.book Page 32 Tuesday, September 28, 2010 9:55 AM 32 RFS4011 Series Integrated Services Controller: Installation Guide Taiwan 在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用 Korea 당해 무선설비는 운용 중 전파혼신 가능성이 있음 당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 Turkish WEEE Statement of Compliance EEE Yönetmeliğine Uygundur .
RFS4000_Baseline.book Page 33 Tuesday, September 28, 2010 9:55 AM Regulatory Information Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Symbol for recycling. For information on how to return product, please go to: http://www.symbol.com/environmental_compliance. Dansk: Til kunder i EU: Alle produkter skal returneres til Symbol til recirkulering, når de er udtjent.
RFS4000_Baseline.book Page 34 Tuesday, September 28, 2010 9:55 AM 34 RFS4011 Series Integrated Services Controller: Installation Guide Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Symbol al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.symbol.com/ environmental_compliance.
RFS4000_Baseline.book Page 35 Tuesday, September 28, 2010 9:55 AM Part Numbers, Support, and Sales 7 Part Numbers, Support, and Sales Part Numbers Description Part Number RFS4011 Series Integrated Services Controller with Internal PoE and Power Supply (US Onlyl) RFS-4011-11110-US RFS4011 Series Integrated Services Controller with Internal PoE and Power Supply RFS-4011-11110-WR Rack Mount Kit RFS-4011-MTKT2U-WR Antenna Facade (ANT:802.
RFS4000_Baseline.book Page 36 Tuesday, September 28, 2010 9:55 AM 36 RFS4011 Series Integrated Services Controller: Installation Guide 8 Motorola, Inc. End-User License Agreement BY DOWNLOADING, INSTALLING, OR USING THE SOFTWARE DESCRIBED IN THIS DOCUMENT, YOU OR THE ENTITY OR COMPANY THAT YOU REPRESENT ("LICENSEE") ARE UNCONDITIONALLY CONSENTING TO BE BOUND BY AND ARE BECOMING A PARTY TO THIS LICENSE AGREEMENT ("AGREEMENT").
RFS4000_Baseline.book Page 37 Tuesday, September 28, 2010 9:55 AM Motorola, Inc. End-User License Agreement interrupt, destroy or limit the functionality of any computer software or hardware or telecommunications equipment. Licensee, not Licensor, remains solely responsible for all Content that Licensee uploads, posts, e-mails, transmits, or otherwise disseminates using, or in connection with, the Software. 4 FEES; SUPPORT AND UPGRADES.
RFS4000_Baseline.book Page 38 Tuesday, September 28, 2010 9:55 AM 38 RFS4011 Series Integrated Services Controller: Installation Guide 9 INDEMNITY. Licensee agrees that Licensor shall have no liability whatsoever for any use Licensee makes of the Software.
RFS4000_Baseline.
RFS4000_Baseline.
RFS4000_Baseline.book Page 1 Tuesday, September 28, 2010 9:55 AM MOTOROLA INC. 1303 E. ALGONQUIN ROAD SCHAUMBURG, IL 60196 http://www.motorola.
