User's Manual
Table Of Contents
- Proprietary Statement
- Document Conventions
- Introduction to the RW Series
- Unpacking and Inspection
- Reporting Damage
- Getting Ready to Print
- Battery Safety
- Charger Safety
- Installing RW Series Batteries
- The LI72 Charger
- Charging Battery Packs with the LI72 Two-Wire Version
- Charging Battery Packs with the LI72 Three-Wire Version
- Model UCLI72-4 Quad Charger
- Loading the Media
- Loading Media Procedure
- Loading Media From An Internal Supply
- Loading Media From An External Supply
- Operator Controls
- Control Panel
- Programmable LCD Settings
- Verify the Printer Is Working
- Printing a Configuration Label
- Connecting the Printer
- Cable Communications
- Serial (RS232C) and USB Combination Port
- USB
- Wireless Communications
- Wireless Communications with Bluetooth®
- Bluetooth Networking Overview
- Wireless Local Area Network Overview
- Setting Up the Software
- Radio Regulatory Information
- Bluetooth RW -ZBR3 Radio (RW 220 and RW 420)
- European Regulatory Information for the RW-ZBR3 Bluetooth Radio
- Europe – EU Declaration of Conformity
- Zebra Bluetooth Radio 2.0 RW-ZBR4 (RW 220 and RW 420)
- European Regulatory Information for this Radio
- Europe – EU Declaration of Conformity
- Compact Flash (802.11b) Radio Module
- European Regulatory Information for this Radio
- Europe – EU Declaration of Conformity
- Zebra Value Radio, 802.11b
- European Regulatory Information for this Radio
- Europe – EU Declaration of Conformity
- WLAN Module Using 802.11b/g Radio
- European Regulatory Information for this Radio
- Europe – EU Declaration of Conformity
- Republic of China Regulatory Information for the Compact Flash 802.11b/g Radio
- Compact Flash (802.11b) and Bluetooth Co-located Radio Modules
- European Regulatory Information for the Compact Flash 802.11b Radio and Bluetooth Co-located Radio Modules
- Europe – EU Declaration of Conformity
- Card Reader Options
- Magnetic Stripe Reader
- Smart Card Reader
- Using the Accessories
- Belt Clip
- Adjustable Shoulder Strap
- Cradles
- RW 420 Vehicle Cradle
- Installing the RW 420 in the Cradle
- Removing the RW 420 from the Cradle
- RW 220 Vehicle Cradle
- Installing the RW 220 in the Cradle
- Removing the RW 220 from the Cradle
- Preventive Maintenance
- Extending Battery Life
- General Cleaning Instructions
- Troubleshooting
- LCD Control Panel Indicators
- Troubleshooting Topics
- Troubleshooting Techniques
- Printing a Configuration Label
- Performing a Forced Shutdown
- Communications Diagnostics
- Calling Technical Support
- Specifications
- Printing Specifications
- Memory/Communications Specifications
- RW 420 Media Specifications
- RW 220 Media Specifications
- Communications Ports
- USB
- RS232/USB
- Font/Bar Code Specifications
- Physical/Environmental/Electrical Specifications
- RW Series Accessories
- Appendix A
- Interface Cables
- RS232 Download Cable
- USB Download Cable
- USB Cable
- Appendix B
- Media Supplies
- Appendix C
- Maintenance Supplies
- Appendix D
- Product Support
- Appendix E
- Battery Disposal
- Product Disposal
- Appendix F
- Using zebra.com
- Index
- Patent Numbers
12
RW Series User Guide
Figure 4: Installing the RW 220 Battery
Figure 3: Installing the RW 420 Battery
Rotate Belt Clip out of
the way.
Insert this end of the
Battery Pack into the
printer
Rock the Battery Pack into
the Printer until the latch
clicks into place.
Insert this end of the
Battery Pack into the
printer
Rock the Battery Pack into
the Printer until the latch
clicks into place.
Rotate Belt Clip out of
the way.