User's Manual

Rugged Bluetooth
Headset
Zebra reserves the right to make changes to any product to improve reliability,
function, or design. Zebra does not assume any product liability arising out of,
or in connection with, the application or use of any product, circuit, or
application described herein. No license is granted, either expressly or by
implication, estoppel, or otherwise under any patent right or patent, covering or
relating to any combination, system, apparatus, machine, material, method,
or process in which Zebra products might be used. An implied license exists
only for equipment, circuits, and subsystems contained in Zebra products.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Service Information
Before you use the unit, it must be configured to operate in your facility’s
network and run your applications.
If you have a problem running your unit or using your equipment, contact your
facility’s Technical or Systems Support. If there is a problem with the
equipment, they will contact the Zebra Global Customer Support at:
http://www.zebra.com/support.
For the latest version of this guide go to: http://www.zebra.com/support.
Zebra Technologies Corporation, Lincolnshire, IL USA
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered
in many jurisdictions worldwide. All other trademarks are the property of
their respective owners.
© 2016 Symbol Technologies LLC, a subsidiary of Zebra Technologies
Corporation. All rights reserved.
HS3100
Quick Start Guide
MN-002762-01 Revision A — July 2016
OTH BTN
Features
Over-the-Head (OTH)
Behind-the-Neck (BTN)
Note: This guide applies to both the OTH and BTN
headband models, unless otherwise noted.
Buttons/LED
Charge the Battery
Insert the battery into the charger with the contacts facing forward.
Insert the Battery
Insert the battery with the contacts facing outward.
Power On Headset
Press the Main Function button to turn the power on. The headset LED
illuminates blue and flashes three times.
Pair Headset with Device
The headset can be paired in any of the following ways:
• Tap to Pair (NFC Pairing)
• Scan to Pair (Bar Code Pairing)
• Manual Pairing (Provisioning the HS MAC Address)
Position the Boom
Do not rotate the boom beyond the stop point.
* Applies to OTH model. The BTN model has only left side boom
placement.
Adjust the OTH Headband
The headband can be squeezed for a tighter fit to the head and clicks as it
is positioned into place. When adjusting the headband,
• Position the ear pad in the center of the ear.
• Position the T-Bar above the ear, half way between the top of the ear
and the top of the head.
* Applies to OTH model.
Adjust the BTN Headband Strap
Loosen or tighten the velcro closure on each end to increase or decrease
the length of the strap.
Slide the clips forward or backward to move the strap closer or further from
the headband.
* Applies to BTN model.
Adjust the Microphone
Position the microphone icon so that it is facing your mouth.
Adjust the Microphone Boom
Place the microphone two finger’s width away from the corner of your
mouth, so it is slightly to one side.
Mute the Microphone
Place the microphone boom in the upright position.
Adjust the Volume
Audio Tones and Prompts
Maintenance
Replace T-Bar
* Applies to OTH model.
Replace Headband Pad
Remove the T-Bar and then the headband pad.
Replace the headband pad and then the T-Bar.
* Applies to OTH model.
Replace Headband
Disassemble the headset to replace the headband.
Replace Ear Pad
Firmly grip and pull the ear pad and inner casing.
Align and snap the new fear pad into position.
Replace Windscreen
Remove the Battery
Buttons/
Function
LED Indicator
Main Function Button
Power ON Blue and flashes three times
Power OFF Red and flashes three times
Pair Blue and Red alternate flash
Connection Status
Adjustable
Headband
Microphone with
Windscreen
Flexible Microphone
Boom
T-Bar
Single Ear
Piece
Battery
Ear Piece
Assembly
Disassembly
Knob
Buttons/
LED
Microphone with
Windscreen
Flexible Microphone
Boom
Disassembly
Knob
BTN
Headband
with
Adjustable
Strap
Battery
Buttons/
LED
Left Placement
Single Ear Piece
NFC Tag
Main
Function
Button
Volume
Not Connected Blue
Connected Blue flash every two seconds
Battery Status
Low Battery Shutdown Red and flashes three times
Low Battery Warning Red flashes twice every two seconds until
battery shutdown
Battery Charging (USB) Red
Main Function Button
NFC Tag
NFC Pairing Bar Code Pairing
Left Side Boom
Placement
Right Side Boom
Placement
Function Audio Tone/Prompts
Start Pairing Tone: Two short beeps - low
Successful Pairing Tone: Three beeps - raising
Device Connected Tone: One beep
Prompt: From the application
Bluetooth Link Lost Tone: Two low tones followed by high tone
Low Battery Tone: Two short beeps triggered every two
minutes until shutdown
Prompt: While connected from the application
Volume UP/DOWN Buttons
Low Backup Power
Time
Tone: ??
Prompt: ??
Mute Tone: Two tones failing
Un-mute Tone: Two tones raising
To On Tone: Four rising tones
To Low Power Tone: Four descending tones
1
2
3
4