User's Manual

ManualsBrandsZebra Technologies ManualsElectronicsBT5 Radio Module



UserManual

EYSNSNZWWZ1



ComplianceandRegulatoryStatements



FCCComplianceStatement(USA)

ThisdevicecomplieswithPart15.247.Operationissubjecttothefollowingtwoconditions:

1. Thisdevicemaynotcauseharmfulinterference.

2. Thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycause

undesiredoperation.

ThisequipmenthasbeentestedandfoundtocomplywithClassBDigitalDevices,pursuanttoPart15of

theFCCrules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterference

whentheequipmentisoperatedinaresidentialenvironment.Thisequipmentgenerates,uses,andcan

radiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeproductmanuals,

maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethat

interferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterference

toradioortelevisionreception,theuserisencouragedtoemployoneormoreofthefollowing

measures:

 Reorientorrelocatethereceivingantenna

 Increasetheseparationbetweentheequipmentandreceiver

 Connecttheequipmenttoanoutletonacircuitdifferentfromthattowhichthereceiveris

connected

 ConsultthedealeroranexperiencedRFservicetechnicianforhelp



Theendproductmustbelabeled,inavisiblearea,withthefollowing:

ContainsFCCID:I28‐EYSNSNZWWZ1



ModificationWarning

TheuseriscautionedthatanychangesormodificationsnotexpresslyapprovedbyZebraTechnologies

couldvoidtheuser’sauthoritytooperatetheequipment.Toensurecompliance,thisprintermustbe

usedwithfullyshieldedcommunicationcables.



RFExposureStatement

ThistransmittercomplieswithFCCradiationexposurelimitssetforthforanuncontrolledenvironment.

Thistransmittermustnotbeco‐locatedoroperatinginconjunctionwithanyotherantennaor

transmitter,exceptinaccordancewithFCCmulti‐transmitterproductprocedures.



Summary of content (4 pages)

PAGE 1
User Manual EYSNSNZWWZ1 Compliance and Regulatory Statements FCC Compliance Statement (USA) This device complies with Part 15.247. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with Class B Digital Devices, pursuant to Part 15 of the FCC rules.
PAGE 2
Canadian DOC Compliance Statement Cet appareil numerique de la classe B est conforme a la norme NMB‐003 du Canada. This Class B digital apparatus complies with Canadian ICES‐003. Innovation, Science, and Economic Development Canada (ISED) Warning Le present appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 3
Note: a wide GND area must be provided to ensure isolation for each layer General The EYSNSNZWWZ1 module has been certified as a Full Modular device, and is not a Limited Module. Additional evaluation is required for use in all host devices. Maximum ratings and operational conditions: The following describes the installation procedures for the various hosts in which the module has been evaluated.
PAGE 4
The EYSNSNZWWZ1 module is not intended for OEM integrations or end users. It can only be installed in the Zebra printers at the grantee manufacturing facility. Test Modes and Testing Requirements This transmitter is to be tested while installed into a host device. The operational test modes are as follows:   Normal connection mode paired with a separate master device Continuous wave transmission mode: Channels 0‐39 selectable, output power selectable, modulated and unmodulated transmission selectable.