User's Manual
Table Of Contents
- IBM Interface
- Wand Emulation Interface
- Scanner Emulation Interface
- 123Scan2
- OCR Programming
- Introduction
- OCR Parameter Defaults
- OCR Programming Parameters
- Enable/Disable OCR-A
- OCR-A Variant
- Enable/Disable OCR-B
- OCR-B Variant
- Enable/Disable MICR E13B
- Enable/Disable US Currency Serial Number
- OCR Orientation
- OCR Lines
- OCR Minimum Characters
- OCR Maximum Characters
- OCR Security Level
- OCR Subset
- OCR Quiet Zone
- OCR Bright Illumination
- OCR Template
- OCR Check Digit Modulus
- OCR Check Digit Multiplier
- OCR Check Digit Validation
- Symbologies
- Introduction
- Scanning Sequence Examples
- Errors While Scanning
- Symbology Parameter Defaults
- UPC/EAN
- Enable/Disable UPC-A
- Enable/Disable UPC-E
- Enable/Disable UPC-E1
- Enable/Disable EAN-8/JAN-8
- Enable/Disable EAN-13/JAN-13
- Enable/Disable Bookland EAN
- Decode UPC/EAN/JAN Supplementals
- User-Programmable Supplementals
- UPC/EAN/JAN Supplemental Redundancy
- UPC/EAN/JAN Supplemental AIM ID Format
- Transmit UPC-A Check Digit
- Transmit UPC-E Check Digit
- Transmit UPC-E1 Check Digit
- UPC-A Preamble
- UPC-E Preamble
- UPC-E1 Preamble
- Convert UPC-E to UPC-A
- Convert UPC-E1 to UPC-A
- EAN-8/JAN-8 Extend
- Bookland ISBN Format
- UCC Coupon Extended Code
- ISSN EAN
- Code 128
- Code 39
- Code 93
- Code 11
- Interleaved 2 of 5 (ITF)
- Discrete 2 of 5 (DTF)
- Codabar (NW - 7)
- MSI
- Chinese 2 of 5
- Matrix 2 of 5
- Korean 3 of 5
- Inverse 1D
- Postal Codes
- GS1 DataBar
- Composite
- 2D Symbologies
- Redundancy Level
- Security Level
- Report Version
- Macro PDF Features
- Advanced Data Formatting
Advanced Data Formatting 15 - 27
Setup Field(s)
Send Data (continued)
Send Next 19 Characters
Send Next 20 Characters
Table 15-2
Setup Field(s) Definitions
Parameter Description Page
Move Cursor
Move Cursor To a Character Scan the
Move Cursor To Character on page 15-28
, then any
printable ASCII character from the
Alphanumeric Keyboard on page
15-87
. This moves the cursor to the position after the matching
character. If the character is not there, the rule fails and ADF tries the
next rule.
15-28
Move Cursor to Start of Data Scan this bar code to move the cursor to the beginning of the data. 15-28
Move Cursor Past a Character This action moves the cursor past all sequential occurrences of a
selected character. For example, if the selected character is ‘A’, then
the cursor moves past ‘A’, ‘AA’, ‘AAA’, etc. Scan the
Move Cursor Past
Character on page 15-28
, then select a character from the
Alphanumeric Keyboard on page 15-87
. If the character is not there,
the cursor does not move (i.e., has no effect).
15-28
Skip Ahead “N” Characters Scan one of these bar codes to select the number of positions ahead
to move the cursor.
15-29
Skip Back “N” Characters Scan one of these bar codes to select the number of positions back to
move the cursor.
15-30
Send Preset Value Send Values 1 through 6 by scanning the appropriate bar code. Set
these values using the prefix/suffix values in
Table 7-4 on page 7-19
.
Value 1 = Scan Suffix
Value 2 = Scan Prefix
Values 3-6 are not applicable
15-30