SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Revision: 3.3.0.
SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Package Contents One access point One clamp One ground wire One mounting bracket + Four screws Two waterproof cable glands Note: SP230 and SP230-S5 both provides two waterproof cable glands. Installation Requirements TERMS OF USE: All Ethernet cabling runs must use CAT5e, 24 AWG (or above) Shielded Twisted Pair (STP) cabling.
SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Two-dimensional Mounting Kit (Optional accessory_SP-MKM5) Pole-Mount Attach the intermediate steel plate to the Attach the two-dimensional mounting device using four M5 screws (included in the bracket to the intermediate steel plate using packaging). Securely tighten the screws. four M4 screws (included in the packaging). Securely tighten the screws.
SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG screws (included in the packaging). (included in the packaging). Securely tighten the Securely tighten the screws. screws. Attach half-mounting bracket to the M-type bracket, then screw four hex head machine bolts. Securely tighten the screws. Anti-theft Steel Rope (Optional accessory_SP-CBM5) Insert three anti-theft screws (included in the packaging) to the device through the mounting bracket. Securely tighten these three screws.
SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Grounding Connection & Protect from Lightning 1. Make your device GND port connect to ground wire. 2. The ground wire connects to the earth. In addition, the grounding wire meets to 6-AWG copper grounding wire. Note: Be sure that grounding is available and that it must comply with local and national electrical codes. For additional lightning protection, use lightning rods and lightning arrestors. Safety Notice 1.
SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Powering the Access Point Connect the PoE cable into the WAN/PoE IN port of the device. Note: Please wait for 5-10 seconds while powering on. Note: For PoE Out applications, the LAN port provides DC 48V, Max. 208mA, and up to 10W power supply. The positive side of the 48V is connected to pin 4 and 5, the negative side is connected to pin 7 and 8.
SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Note: The following procedure assumes that Windows 10 is the operating system. Procedures for other operating systems are similar. Step 1. On your computer, configure your network adapter from the “Local Area Connection “settings as follows: ˙ Step 2. StartControl PanelNetwork & InternetChange Adapter OptionsEthernet Edit the TCP/IPv4 address setting as follows: ˙ PropertiesInternet Protocol Version 4(TCP/IPv4) Step 3.
SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Note: For bridge mode settings, please refer to the user manual for more information. https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=25 Technical Specifications Physical Dimensions 151 x 75.5 x 235 mm (L x W x H) (5.94 x 2.97 x 9.25 in) Weight 1000 grams (2.2 lbs.) SP230 Antenna SP230-S5 WAN/PoE In Port One 10/100/1000 Mbps port LAN Port One 10/100/1000 Mbps port 2.4GHz: Embedded 5.5 dBi antennas 5GHz: Embedded 6.
SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Compliance FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
SP230/SP230-S5 2x2 PtP/PtMP 802.11ac Wave 2 Access Point QSG Country List BFWA (Broadband Fixed Wireless Access) members noted in blue Note: This device meets Max. TX power limit per ETSI regulations. The following apply to products that operate in the 5 GHz frequency range: Note: This device is restricted to indoor use only when operating in the 5150 - 5350 MHz frequency range within all member states. Note: Operation in the 5.8 GHz frequency band is prohibited in BFWA member states.
SP230/SP230-S5 2x2 PtP/PtMP 802.
