Quick Setup Guide

ManualsBrandsZCOM ManualsComputers & Accessories802.11ac Access Point

This Quick Setup Guide provides step-by-

step instructions on how to set up your

Access Point. After completing the steps

described in this Guide, you will be able to

place the AP at your site and provide

wireless network access to users.

PACKAGE CONTENTS

Z-COM, Inc.

SP220-C02

802.11ac Wireless Access Point

Quick Setup Guide

• A computer running Windows 7, Vista, or XP

• A CAT5 UTP cable of required length

• Power adapter/PoE injector came with the

package. (4-Pair 802.3at PoE injector 60W)

STEP 1: POWER ON THE AP

The Access Point comes with a PoE injector kit

for connecting to power over the Ethernet port.

The Access Point automatically turns on as soon

as it is connected to a power source.

SETUP REQUIREMENTS

Before installing your Access Point, be sure that

you have the following:

• Wireless Access Point (1)

• Mounting screws and bracket (1)

HARDWARE OVERVIEW

Front View

LED Indicators on the Device

LED State Description

1 PWR

Off No power to AP

Green

AP power on, device

ready

2 WLAN

Off

2.4G/5G radio

disabled

Blinking

Green

2.4G/5G radio

enabled or data

being forwarded

3 LAN

Off

Ethernet port not

connected

Green

Ethernet port

connected

Blinking

Green

Ethernet link activity

No. Item

1 Ground

2 LED

PoE/LAN Port

4 Reset Button

5 LAN Port (Option)

Rear View

Bottom View

Summary of content (7 pages)

PAGE 1
Z-COM, Inc. SP220-C02 Rear View 802.11ac Wireless Access Point Quick Setup Guide This Quick Setup Guide provides step-bystep instructions on how to set up your Access Point. After completing the steps described in this Guide, you will be able to place the AP at your site and provide wireless network access to users. PACKAGE CONTENTS LED Indicators on the Device No 1 2 LED PWR Description Off No power to AP No. Item Green On AP power on, device ready 1 Ground 2 LED Off 2.
PAGE 2
Cautions: 1. Use only the power adapter and PoE injector that came with the wireless AP. 2. Make sure that the PoE injector is properly grounded 1. Insert one end of an Ethernet cable to the P+D/OUT port on the PoE injector. 2. Insert the other end to the LAN/PoE port on the Access Point. 3. Connect a power cord to the PoE injector. 4. Connect the power plug to a wall socket. STEP 2: CONNECT THE AP TO YOUR PC 1. Insert one end of an Ethernet cable to the DATA/IN port on the PoE injector as figured above.
PAGE 3
4. Configure the common RF setting as such Country/Region domain and Channel. 5. Click Apply to save the changes. Configuring for Standalone Operation Before configuring fat AP Basic settings, make sure that AP mode is set to Fat AP. 1. If currently in Thin AP Mode: On the main menu on the left, click Advanced Setting. Select Fat AP from the drop-down list. Click Apply to take effect. 3. Go to RF Configure > Wireless Settings.
PAGE 4
STEP 5: INSTALL THE AP 1. Disconnect the AP’s power adapter from the power outlet (or disconnect the PoE cable). 2. Move the AP to its permanent location (accessible to both power source and network connections). 10. In Network Authentication, select the desire authentication method and then enter the encryption phrase accordingly. 11. Click Apply to save the changes. 12. Click Logout to exit the Web interface. STEP 4: VERIFY THE CONNECTION 1. Connect the AP to your network. 2.
PAGE 5
3. Slide the gasket and rubber stopper into the locking nut. 4. Connect the RJ-45 connector into the LAN port of the Access Point. 5. Flush the gasket, rubber stopper and locking nut together into the LAN port opening, then twist the locking nut to seal the opening. 6. Slide the sealing cap over the bare end of the Ethernet cable. 7. Tighten the sealing cap. 2. Insert the other end of an Ethernet cable to the P+D/OUT port on the PoE injector.
PAGE 6
Compliance Information RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
PAGE 7
NCC使用手冊警語: 根據 NCC 低功率電波輻射性電機管理辦法規定：第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。減少電磁波影響，請妥適使用。本產品使用安裝時，應避免影響附近雷達系統之操作。高增益指向性天線，只得應用於固定式點對點(Point to Point)系統應用。本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者。本產品使用時，建議至少距離人體20cm以上。電磁波曝露量MPE標準值1mW/cm2 ，送測產品實測值為：0.289 mW/cm2。 Copyright © 2016 Z-Com, Inc. All rights reserved.