User guide
zBoost
®
SOHO Xtreme YX545x User Guide
6
zBoost
®
SOHO Xtreme YX545x User Guide
7
Setting Up Your zBoost Signal Booster
Minimum Performance: Outside of a window
Locate a window where you get signal.
1. Mount the Signal Antenna outside of the window in the
area of strongest signal.
2. Assemble the Panel Antenna. Place the Base Unit in
desired location – where you want to create a Cell
Zone™ (15 feet of vertical separation between the Base
Unit and Signal Antenna is recommended).
3. Attach the coaxial cable to the Signal Antenna.
4. Run the coaxial cable from the Signal Antenna through
the window (an optional window entry kit is available: see
page iv) and to the Base Unit.
5. Attach the Base Unit Antenna to the Base Unit using the provided cable.
6. Connect the Power Supply to the Base Unit and plug into a power outlet.
NOTE: The zBoost Xtreme requires at least 15 feet of vertical separation between the Signal
Antenna and the Panel Antenna. Generally, increasing this distance (up to 40 feet) will increase the
performance and decreasing the distance will limit zBoost performance.
Upon initial power up, a solid GREEN light should appear indicating normal conditions. If a RED
light appears, adjustments may be needed to optimize performance. If you nd the increased signal
coverage is acceptable, however, no additional adjustments are needed. See Light Indicator section
(page 10) for more information.
*An 8 inch window entry cable may be needed for this option. It is available for purchase at
www.Wi-Ex.com (Part #: YX030-08W).
Minimum Performance
Place Signal Antenna
outside of window*
Placement of the Signal Antenna
Choosing the best location for the Signal Antenna provides the best performance and the largest
area of improved signal. Choose a location for the Signal Antenna using your cell phone to
determine the area of strongest signal - typically found outside, above the rooine or in an attic. The
antenna must also remain at least 3 feet from any metal.
Keep in mind that the coverage zBoost provides is largely determined by the quality of signal
received by the Signal Antenna. If your best signal is one bar, your coverage will be limited to one
small room. IMPORTANT: Incorrect assembly of the Signal Antenna to the mounting bracket (see
gure A) will impede performance. Ensure that the Signal Antenna is properly positioned in the
mounting bracket as pictured.
To mount Signal Antenna to a pole: Attach antenna to pole bracket as pictured. Use U-Bolt to
secure bracket to pole and fasten. DO NOT mount to a metal pole.
To mount Signal Antenna to a at surface: Attach antenna to pole bracket as pictured. Secure
bracket to desired surface using provided screws. Use of the Saddle and U-Bolt are not necessary
for this option. Choose 1 of the following options for setting up your zBoost® system:
Maximum Performance: Attic/Outdoor placement
The following instructions are recommended for
the best reception:
1. Using your cell phone as a signal meter, conrm
that either your attic or your roof will deliver
optimal signal strength to the Signal Antenna.
Identify the best location for attachment of the
mounting bracket – such as an attic cross or
main beam.
2. Secure the mounting bracket at the highest
possible point and at least 3 feet away from metal
objects such as pipes, metal siding, A/C unit etc).
Position the mounting bracket such that the Signal
Antenna will be vertical and attach the Signal
Antenna. See page 6 for more information.
3. Connect the supplied coaxial cable to the base of
the Signal Antenna. Run the coaxial cable along a descending pipe or through a wall that
that leads closest to the location of the Base Unit. Use the provided 50 feet of RG-6 coaxial
cable to connect the Signal Antenna and the Base Unit. Should you need additional cable
length, 15 foot extensions (Part #: YX030-15w) are available at www.Wi-Ex.com. Please
note: Cable longer than 65 feet is not recommended.
NOTE: Refrain from securing cable or drilling holes until the system has been tested.
4. Connect the RG-8 coax cable it to the other end of the Base Unit. Mount the Panel Antenna
on a wall facing the direction where increased coverage is desired to create a Cell Zone.
Connect the Panel Antenna to the Base Unit. Place the zBoost Base Unit where you want
it. For the widest possible signal area, mount it is recommended that you mount the Panel
Antenna on an interior wall facing the center of the room.
5. Connect the zBoost Base Unit to the provided power supply and plug into a power outlet.
When your zBoost system is in place and fully connected, walk throughout your home or
ofce and verify that you are able to reliably place calls. If the signal strength has improved,
your zBoost is working. Remember, coverage varies based on outdoor signal level, building
construction, and antenna placement. Coverage in adjoining rooms (next to, above, or
below) will be reduced by walls and ceiling/oors.
15’ of vertical
separation
15’ of vertical
separation
15’ of vertical
separation
Maximum Performance
Place Signal Antenna
on roof or in attic
zBoost Base Unit
Power Supply
RG-8x
Panel Antenna
Coaxial Cable