User guide

zBoost
®
SOHO Xtreme YX545x User Guide
4
zBoost
®
SOHO Xtreme YX545x User Guide
5
Pole Bracket
Saddle
U-Bolt
Before installing, please note the following important factors in determining your zBoost
performance:
• At least 15 vertical feet is needed between the Signal Antenna (receives the outside signal)
and the Panel Antenna (rebroadcasts the signal indoors). Separation less than 15 vertical feet
will result in decreased performance. See illustration below.
• Keep the Signal Antenna at least 3 feet above any metal. It is recommended that the Signal
Antenna and Base Unit Antenna have at least 15 feet of vertical separation.
To capture the best signal, place
the Signal Antenna as high as
possible and position it vertically,
keeping it at it at least 3 feet away
from any metal.
See page 6, Setting Up Your
zBoost Product, for additional
information.
The Panel Antenna should
be mounted on a wall facing
the direction where increased
coverage is desired. Note that
signal is broadcasted in a 70° beam width from the front of the Panel Antenna. Keep the Panel
Antenna off oor and at least 3 feet away from other cords, metal objects or other wireless devices
such as wireless routers or wireless access points. The zBoost Xtreme performs best when there
are no obstructions
between the Panel
Antenna and your mobile
device. Determine
the Location of Signal
Antenna and Base Unit
Antenna
Additional Cable Requirements
Use the provided 50 feet of RG-6 cable to connect the Signal Antenna and the Base Unit. Should
you need additional cable length, 15 foot extensions (Part #: YX030-15w) are available at www.
Wi-Ex.com. RG-6 is also available at many home improvement or electronic stores.
The total cable length should not exceed 65 feet unless you also purchase an upgraded signal
antenna (see page iv). A longer cable is helpful only if it allows you to place the Signal Antenna in a
location where you measure stronger signal.
Grounding the Signal Antenna
If you decide to place the Signal Antenna outdoors, it must be properly grounded. (See page iv for a
recommended grounding kit).
The set up must be in accordance with Article 810 of the National Electric Code (NEC). A listed
antenna discharge unit must be provided for the lead-in coaxial cable per NEC article 8.10.20 or
the shield of the coaxial cable must be permanently and effectively grounded in accordance with
NEC article 8.10.21. Please consult a professional installer or
electrician for more information.
Securing Cable with a Drip Loop
If you place the Signal Antenna outdoors, create a drip loop
with the coaxial cable at the point where the cable enters the
building through an outside wall. This can be done by twisting
and securing the cable into a loop (no less than 4” across) near
the entry point. This will help prevent moisture from gathering at
entry point and leaking into the building. Consult a professional
installer if you need more information.
Power Requirements
The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the Included
power supply. The power supply consumes less than 10W (less than 0.2A).
Antenna Bracket Assembly
IMPORTANT: Incorrectly mounting the Signal Antenna to the mounting
bracket (see gure A) will impede performance. Ensure that the Signal
Antenna is properly positioned in the mounting bracket as pictured
below.
To mount antenna to a pole: Attach bottom of antenna to pole bracket
as pictured. Use U-Bolt to secure bracket to pole and fasten.
To mount antenna to a at surface: Attach bottom of antenna to pole
bracket as pictured. Secure bracket to desired surface using provided
screws. Use of the Saddle and U-Bolt are not necessary for this option.
Figure A
Figure A
Warning
Avoid placing the Signal Antenna near metal such as
wiring, A/C ducts, metal siding, truss plates, etc.
When connecting the cable to the antenna, run the
cable straight down from the antenna. Avoid draping
the coax near the antenna.
Note
The zBoost Xtreme YX545x base unit MUST only be
used with the provided power adaptor. Use of other
power adaptors will void the warranty and may damage
the unit. Use of other equipment is not FCC approved.
Maximum Performance Minimum Performance
15’ of vertical
separation
15’ of vertical
separation
15’ of vertical
separation
Signal is emitted in a beam width of 70° horizontal and 60° vertical
Coax Cable
Exterior Wall