Zavio D520E Quick Installation Guide Please follow the installation steps below to set up your D520E IP Camera. Check the package contents against the list below. See P.1 Physical overview. See P.2 Install the hardware and connect all cables. See P.3 Microsoft OS: Use the software CD to install Intelligent IP Installer. See P.7 Access the IP Camera using Intelligent IP Installer. See P.7 Mac OS using Safari Browser. See P.9 Change light environment setting. See P.
Physical overview Dome cover Reset button Rugged dome Wire clip Conduit hole plug Cable gland Cable gland Claw Thread-lock sealing nut Note: The size of Cable gland is M20*1.
Install the hardware and connect all cables a. Installer the hardware 1. Loosen the tamper-proof screws using supplied special hex wrench and remove the dome cover from the rugged dome. Be careful do not scratch the cover glass. 2. Disassemble the cable gland. 3. Thread the network and I/O cable (power/audio/digital input and digital output) through thread-lock sealing nut, claw (using the claw to round all cable) and cable gland. To seal all cable in the claw part tightly in case of water leaking. 4.
b.Wall mounting and Ceiling mounting Plastic anchor nuts 1. Paste the drill template on the Wall or Ceiling which rugged dome desired. 2. Drill four holes in the wall or ceiling and insert plastic anchor nuts into them. 3. Insert the supplied screws into the corresponding anchor nuts and secure them with screwdriver. 4. Cover the rugged dome and tighten the tamper-proof screws using the special hex wrench.
Bolt c. Mounting with Bracket (Optional) 1. Route network and power cables through wall and allow extending. 2. Loosen the two bolts to rotate bracket to the desired position. 3. Thread all cable through cable gland. 4. Route network cable and power cable and fixe those with wire clip. 5. Attach cable gland on the conduit hole. 6. Fix wall mounting bracket on rugged dome with four supplied wash and screws.
. Drill four holes and insert plastic anchor nuts into them. 8. Insert the supplied screws into the corresponding anchor nuts and secure them with screwdriver. d1 d. Connect all cables b1. Power over Ethernet (PoE) 1. Using a standard RJ-45 network cable, connect the IP Camera to a PoE-enabled Hub / Switch / Router b2. Without Power over Ethernet (PoE) connection 1. Connect the power adaptor to the IP Camera. 2. Using a standard RJ-45 network cable, connect the IP Camera to a normal Hub / Switch / Router.
Microsoft OS: Use the software CD to install Intelligent IP Installer Power on your PC and insert the CD-ROM. The setup page will show up automatically. Please follow those steps to install the firmware. Select “Intelligent IP Installer” and follow the installation process to complete the installation. Access the IP Camera using Intelligent IP Installer 1. Before using Intelligent IP Installer, please check two setting. a. Browser’s Internet Properties → Security → Default Level b.
3. Enter your Username and Password to login to the IP Camera. (Default is admin / admin) 4. When accessing the IP Camera for the first time, a yellow information bar appears below the address bar: This website wants to install the following add-on: ‘AxvideoView.cab from ‘Zavio Inc’. 5. Click the information bar, and select Install ActiveX control. 6. Click Install. 7. Live video displays in the centre of your web browser.
Mac OS using Safari Browser 1. Select Safari icon 2. Click Bonjour function and select the camera you wish to access. 3. Enter name and password to login to the IP camera. (Default is admin / admin) 4. The monitor image will be displayed in your browser. Change light environment setting The default setting of lighting environment is 60Hz. However, if the image appears flickery, this might be because the lighting environment in your country is 50 Hz. Hence, this setting can be changed into 50Hz.
Change the Web Interface into your preferred language Use the settings screen to set the language of the Web Interface. Go to “Setting → Basic → System → Initialize”. 1. Insert Software CD into your CD-ROM. 2. Browse and select the preferred language from language pack in the Software CD and then click OK. 3. The web interface will change into your preferred language. Use IP Camera via Mobile Phone 1.
Messenger 7. The IP Camera will send you a message with its Public IP and Private IP if the IP Notification Option is enabled. 8. Click on the small camera icon. Then, choose “View a new contact's webcam”. Camera at home says: 9. The IP Camera automatically accepts your invitation and its live video is displayed. 10. Click Action button and choose Start control panel to use control panel 11. You can use Snapshot, Image Setup function via MSN add-in control panel.
Access to the Internet a. Internet connectivity of the IP camera can be established by inputting the cameras IP information within the Information section. (Please go to Setting → Basic → Network→ Information) b. Internet Connectivity of the IP Camera can be established through PPPoE (Point-to-Point Protocol over the Ethernet) by inputting the username and password from your Internet Service Provider (ISP) within the PPPoE section.
c. Internet Connectivity of the IP Camera can be established if your router is UPnP (Universal Plug and Play) enabled. The IP camera is automatically detected and added to “My Network Places” on your computer. Please note that only Home Routers manufactured after 2006 support the UPnP function. c1. If your router is a UPnP Internet Gateway Device (IGD), turn on the UPnP function within the UPnP section.
Memo ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. …………………………………………………………………………………..
Memo ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. …………………………………………………………………………………..
Memo ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. ………………………………………………………………………………….. …………………………………………………………………………………..
