Installation guide

ManualsBrandsZavio ManualsHome building and DecorD5111

Zavio D5110/D5111 Quick Installation Guide

Please follow the installation steps below to set up your D5110/D5111 Indoor IR Dome Camera.

Check the package contents against the list below. See P.1

Physical overview. See P.1

Install the hardware and connect all cables. See P.3

Microsoft OS: Use the software CD to install Intelligent IP Installer. See P.6

Access the IP Camera using Intelligent IP Installer. See P.6

Change the Web Interface into your preferred language. See P.8

Change lighting setting. See P.8

Auto IRIS setting. See P.8

Day Night function setting. See P.9

Use IP Camera via Mobile Phone. See P. 9

Access to Internet via Static IP, Dynamic IP or both. See P. 10

Application of IP Camera. See P.12

For more information, please check the User Manual available in the Software CD or you can download the latest

software from http://www.zavio.com

Package Contents

Camera

D5110 / D5111 Indoor IR IP Camera

Quick Installation Guide

Brief product information and quick installation

Software CD

IP Surveillance Software

Intelligent IP Installer

User Manuals

Language Packs

Mounting Bracket

Three plastic anchors and screws,

Alignment sticker,

4pin I/O connector

Adaptor

12V DC, max 8W

Physical overview

DI/DO

DO DI GND 12V

Lens rubber

IR LEDs

Card slot

Focus puller

SD Indicator

Zoom puller

PAL/NTSC

Power Indicator

12V DC Jack

Reset button

Ethernet Socket

RCA

Dome bubble

Light sensor

Summary of content (12 pages)

PAGE 1
Zavio D5110/D5111 Quick Installation Guide Please follow the installation steps below to set up your D5110/D5111 Indoor IR Dome Camera. Check the package contents against the list below. See P.1 Physical overview. See P.1 Install the hardware and connect all cables. See P.3 Microsoft OS: Use the software CD to install Intelligent IP Installer. See P.6 Access the IP Camera using Intelligent IP Installer. See P.6 Change the Web Interface into your preferred language. See P.8 Change lighting setting. See P.
PAGE 2
LED Indictor: LED Color Indication Green Steady green for Network link. Orange Flash orange while Network activity. Red Steady red for booting up process; Steady red 30 Seconds when WPS configure failed. Blue Steady blue for booting up competition. Purple Flash purple during firmware upgrading. Unlit When you press reset button. Network Power SD Card Orange Steady orange means SD card ready. Flashes orange while accessing SD card.
PAGE 3
Install the hardware and make all cable connection a. Wall mounting and Ceiling mounting 1. Attach the alignment sticker to the wall/ceiling and drill two pilot holes into it. 2. Hammer the supplied plastic anchors into the holes. 3. Align the three holes on the base of camera with the three plastic anchors on the wall and ceiling, insert the supplied screws to the corresponding hole and screw them. b. Connect all cables b1. Power over Ethernet (PoE) 1.
PAGE 4
c. To adjust the view angle- 3 axis Mechanism Design c1. Turn the lens module right and left to your desired pan position. c2. Turn the lens module up and down to your desire tile position. c3. Turn the lens module to adjust the image orientation to satisfied angle. d. To adjust zoom puller and focus puller (D5111 only) d1. Loosen the zoom and focus pullers anti-clockwise to adjust the desire zoom range and focus. d2.
PAGE 5
f. Completion f1. Clean the dome bubble to remove the dust and finger print. f2. Rotate the black shield on the dome bubble to match the camera’s position. f3.Fasten the dome cover to the base clockwise and make secure two parts reaching the final position by checking two small dots on the side of housing. f4. Slightly adjust dome bubble to final position if needed and double check the camera is properly focused. f5. The installation is complete now.
PAGE 6
Microsoft OS:Use the software CD to install Intelligent IP Installer Power on your PC and insert the CD-ROM. The setup page will show up automatically. Please follow those steps below to install the firmware. Select “Intelligent IP Installer” and follow the installation process to complete the installation. Access the IP Camera using Intelligent IP Installer 1. Before using Intelligent IP Installer, please check two setting. a. Browser’s Internet Properties → Security → Default Level b.
PAGE 7
4. When accessing the IP Camera for the first time, a yellow information bar appears below the address bar: This website wants to install the following add-on: „AxvideoView.cab from „Zavio Inc‟. 5. Click the information bar, and select Install ActiveX control. 6. Click Install ActiveX. 7. Live video displays in the centre of your web browser.
PAGE 8
Change the Web Interface into your preferred language Use the settings screen to set the language of the Web Interface. Go to “Setting → Basic → System → Language”. 1. Insert Software CD into your CD-ROM. 2. Browse and select the preferred language from language pack in the Software CD and then click OK. 3. The web interface will change into your preferred language. Change lighting setting The default setting of lighting environment is Auto.
PAGE 9
Day Night function setting 1. Night ICR Mode: IR and ICR can be controlled separately in case the device needs external IR illuminator. ICR will switch to day or night depending on threshold setting if the setting is auto ICR mode. ICR control can also be set by schedule, choose schedule mode and the Schedule icon will show up below. 2. Switch delay: ICR will switch delay few seconds to avoid sudden brightness and darkness.
PAGE 10
b. 2.5G Mobile Phone Viewing b1. WAP viewing For 2.5G WAP mobile phone viewing, type “ http:///mobile.wml ” into your 2.5G web browser. b1. Browser viewing For 2.5G mobile phone browser viewing, type “http:// /mobile.htm ” into your 2.5G web browser. Access to Internet via Static IP, Dynamic IP or both a. Internet connectivity of the IP camera can be established by inputting the cameras IP information within the Information section. (Please go to Setting → Basic → Network→ Information) b.
PAGE 11
c. Internet Connectivity of the IP Camera can be established if your router is UPnP (Universal Plug and Play) enabled. The IP camera is automatically detected and added to “My Network Places” on your computer. Please note that only Home Routers manufactured after 2006 support the UPnP function. c1. If your router is a UPnP Internet Gateway Device (IGD), turn on the UPnP function within the UPnP section.
PAGE 12
Application of IP Camera 12