F7110 / F7115 User Manual F7110/ F7115 i
F7110 / F7115 User Manual Contents CHAPTER 1. SAFETY INSTRUCTION ....................................................................................................................... 1 CHAPTER 2. MINIMUM SYSTEM REQUIREMENT &........................................................................................... 3 PRODUCT FEATURE..................................................................................................................................................... 3 2.1 SYSTEM REQUIREMENT .
F7110 / F7115 User Manual 8.4.3 IP Filter ......................................................................................................................................................... 53 CHAPTER 9. SETTING-ADVANCED ........................................................................................................................ 53 9.1 PTZ CONTROL .................................................................................................................................................
F7110 / F7115 User Manual User Manual Chapter 1. Safety Instruction Before you use this product This product has been designed with safety in mind. However, the electrical products can cause fires which may lead to serious body injury if not used properly. To avoid such accidents, be sure to heed the following. Legal Caution Video and audio surveillance can be forbidden by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes.
F7110 / F7115 User Manual In case of abnormal operation If the unit emits smoke or an unusual smell, If water or other foreign objects enter the cabinet, or If you drop the unit or damage the cabinet:1 Disconnect the cable and the connecting cables. 2 Contact your authorized dealer or the store where you purchased the product. Transportation When transporting the camera, repack it as originally packed at the factory or in materials of equal quality.
F7110 / F7115 User Manual Chapter 2. Minimum System Requirement & Product Feature 2.1 System Requirement For normal operation and viewing of the network camera, it’s recommended that your system meet these minimum requirements for proper operation: Item Requirements CPU Pentium 4 1.
F7110 / F7115 User Manual 2.
F7110 / F7115 User Manual Chapter 3. Using IP Camera via Web Browser 3.1Windows Web Browser 1. Open your web browser, and enter the IP address or host name of the IP camera in the Location / Address field of your browser. Note : If you only want to view the video without accessing Setting screen, enter “http:///index2.htm” as your web URL. 2. Use the default account “admin” and default password “admin”. Note : The default user name “admin” and the password are set at the factory for the administrator.
F7110 / F7115 User Manual 3.2 Mac Web Browser 1. Click the Safari icon, and enter the IP address of the IP camera in the Location / Address field of your browser. Note : If you only want to view the video without Setting screen “http:///index2.htm” as your web URL. 2. Enter the default account “admin” and default password “admin”. Note : The default user name “admin” and the password are set at the factory for the administrator.
F7110 / F7115 User Manual 3. The monitor image will be displayed in your browser. In the far left side of main configuration are Setting, Client Setting, and Image Setup and PT control. For more details, you can check Chapter 7.2、Chapter 7.3、Chapter 7.4 and Chapter 7.5.
F7110 / F7115 User Manual Chapter 4. Setting up Wireless Configuration (Only for F7115 ) The wireless network has to be set up by using cable network connection. After setting the camera correctly, the wireless function can work without cable network connection. Please follow the setting process below step by step: 1. Connect IP Camera with Ethernet connection. 2.Go to “Setting → Basic → Network → Wireless,” choose option “On”. You will see the wireless Setting screen. 3. Then click “Refresh”.
F7110 / F7115 User Manual 6. Choose the option of Obtain an IP address automatically (DHCP) and Obtain DNS server address automatically. 7. Otherwise, Choose Use the following IP address and Use the following DNS sever address. Use the following IP address: Select this when the fixed IP address is set. IP address: Enter the IP address of the device. Subnet mask: Enter the subnet mask. Default gateway: Enter the default gateway.
F7110 / F7115 User Manual Chapter 5. Operating IP Camera via Mobile Phone 5.1 Mobile Phone Viewing 5.1.1 3G Mobile Phone Streaming Viewing For 3G mobile phone viewing, type “ rtsp://:/video.3gp ” into your 3G Streaming Link. is the Public IP address of your IP camera; is the RTSP port of your IP camera (Default value is 554.) Example: rtsp://100.10.10.1:554/video.3gp Note: You can also use RTSP clients (RealPlayer, VLC, QuickTime Player…etc.
F7110 / F7115 User Manual 5.2 Using IP Camera via iPhone You can use ZAVIO Web User Interface via iPhone. Please follow the setting process below. Then you can use ZAVIO Web UI via iPhone. 2. Type IP address in your web link. 1. Select Safari function 3. Type name and password. Default value is admin / admin. Then click Login In 4. The ZAVIO User Interface and live image will show up in the middle of screen. Note: The image is continuous snapshots, not video. Thus, live image can’t be recorded here.
F7110 / F7115 User Manual Chapter 6. MSN Messenger Please follow the following steps to set up the Messenger function. 1. Download free MSN software and create a new MSN account (Camera at home) for Microsoft Live Messenger. 2.Go to “Setting→Basic→Network→Messenger,” set the Messenger to “ON” . Then, login in new account and password (Camera at home). 3. If your router has firewall function, you have to set the Port Range on this setting page in accordance with the one of firewall. 4.
F7110 / F7115 User Manual 10. The IP Camera will accept your invitation; the live video will show up in the right screen after few seconds. 11. Click Action button and choose Start Control Panel to use control panel. 12. The dialog box will show up with “This application is not part if Window Live Message…….” Tick the box of “Don’t show me this again” and click OK. MSN Messenger 13. The IP Camera will accept your invitation to start Control Panel.
F7110 / F7115 User Manual 15. You can click paint palette icon showing up with tool bar to set up image. Then, you can use the tool bar to optimize video 14. You can click Camera icon to snapshot then the picture will send to you immediately. Brightness , Contrast and Sharpness . , Saturation After the adjustment of all to make setting, you can still click the setting back to the original setting. 16. You can click joystick icon showing up with arrows of different directions.
F7110 / F7115 User Manual Chapter 7. Configuration of Main Menu In the left side of main configuration are Setting, Client setting, Image setting and PT control (appear only when PT/PTZ control enabled). For more details, please check Chapter 7.2、Chapter 7.3、Chapter 7.4.、Chapter 7.5. In the right side, you can control Live View in your main Browser. The functions include Snapshot, Open digital zoom, Audio, and Video Play.
F7110 / F7115 User Manual 7.1 Live View 7.1.1 Snapshot You can capture a still image shot by clicking the camera icon and save it in the operating computer. Symbols Meaning a snapshot window appears after clicking the icon save the picture captured by snapshot into your computer coSave mputer computer. Close Return to the view screen full screen 7.1.2 Digital zoom in / out the image via the monitor window Click Pull the to display the digital zoom in window.
F7110 / F7115 User Manual 7.1.3 Video play buttons Symbols Meaning Pause the current video Play the video Stop the current video Record the current video Note: Concerning the recording storage requirement of your hard disk, please refer to the CHAPTER 10. APPENDIX / B. Storage Requirement Table. 7.1.
F7110 / F7115 User Manual 7.2 Setting This function is only for the Administrator. Click “Setting” on the home page of web user interface to get into the Basic and Advanced settings menu. Click Basic folder, there are sub-folders including System, Camera, Network, and Security. Fore more information, you can see Chapter 8.1、Chapter 8.2、Chapter 8.3 and Chapter 8.4.
F7110 / F7115 User Manual 7.3 Client Setting This function is only for the client. Click this button to control Mode, View Size, Protocol, and Video Buffer. 7.3.1 Mode Click the pull-down box to choose video compression mode of LIVE VIEW among H.264, MPEG-4, MJPEG and JPG. Note: As long as the operating system not able to afford loading under H.264 mode, please downgrade the mode to MPEG-4 or MJPEG. 7.3.2 View Size Select the desired view size of image resolution among 1/4X, 1/2X, and 1X. 7.3.
F7110 / F7115 User Manual 7.4 Image Setup The tool bar can be adjusted to optimize video Brightness, Contrast, Saturation Sharpness and Exposure. 7.4.1 Brightness The value range is 0~99. The higher value the brightness is, the brighter the image is. 7.4.2 Contrast The value range is 0~99. The contrast is a measure of a display system, defined as the ratio of white to black that the system is capable of producing. The higher value the contrast is, the more delicate of color you can have. 7.4.
F7110 / F7115 User Manual 7.5 PT Control 7.5.1 Pan / Tilt / Home control buttons Click the arrow button of the direction you want the IP camera to move. 7.5.2 Other camera control functions Preset: Move the camera toward the preset direction. Patrol: Before you start this function, you need to specify Guard tour settings in the Setting Menu under Advanced / Patrol setting.
F7110 / F7115 User Manual Chapter 8. Setting-Basic Click the Basic folder to display the sub folders including System, Camera, Network, and Security. 8.1 System Click the folder of System to display the sub-folders including Information, Date / Time, Initialize, and Language. 8.1.1 Information The Information screen provides the product factory information which includes Product Name, Firmware Version.
F7110 / F7115 User Manual 8.1.2 Date / Time The Date/ Time screen displays all options of time setting. Current date / time: This displays the current date and time of this IP Camera. PC clock: This displays the date and time of the monitoring PC clock. Date / Time format: You can click the pull down box to select different time display formats.
F7110 / F7115 User Manual Time Zone: Select the Time Zone format of Greenwich Mean Time among different cities. The time display will be the same as the current date / time option. Daylight Saving Time: There are two modes to choose for setting up daylight saving time. By Date: Set the start and end time by select month, day, hour, and minute. By Week Number: Set the start and end time by select month, week, hour, and minute.
F7110 / F7115 User Manual and follow the instructions on the browser to save the setting data file to the location you specified. Restore Setting: Download the saved setting data of this IP Camera. Click “Browse” and select saved file. Click “OK” and this IP Camera is adjusted according to the loaded data and then restarted. Firmware Update: Update the device software. Click “Browse” and select the file for updating. A confirmation dialogue will appear. Click “OK” to start.
F7110 / F7115 User Manual 8.2 Camera Click the folder of Camera to display the sub folders including General, H.264, MPEG-4, MJPEG, 3GPP, and Advanced. 8.2.1 General RTSP: The default value is 554. If the IP Cameras connected with router and installed outside are over 2 sets and all of them need support RTSP, please fill some value in the blank space in the range from 1024 to 65535. RTP Unicast streaming: The default value of port range is 5000 ~ 7999 and can be changed from 1024 to 65535.
F7110 / F7115 User Manual from IP Camera. And you can choose the bit rate from 4.75k to 12.2k. However, the usage of this codec will cause frame-rate decreasing. Off: Select Off, audio file won’t be transmitted by IP CAM. Audio mode: You can select Full duplex or Half duplex. Full duplex: Select it for simultaneous communication in both direction between the connected administrator and IP CAM. It means both parties can speak and be heard at the same time.
F7110 / F7115 User Manual 8.2.2 H.264 Viewer authentication: On: If the viewer authentication is On, the users will be requested to key-in username and password when using QuickTime Player…etc. to have live viewing. Off: If the viewer authentication is Off, you can have live viewing on computer by QuickTime Player…etc. after entering “rtsp://ip:port/video.h264” on the URL column directly. Multicasting streaming (if it’s on): Multicast Address: The multicast server address will appear automatically.
F7110 / F7115 User Manual Quality: Auto: The quality and bitrate will be adjusted automatically according to the frame rate. Fixed Quality: Select the value of quality among Medium, Good, Delicate and Excellent. Fixed Bitrate: Set the bitrate of H.264 image transmission for a line. Select one among 64Kbps, 128Kbps, 256Kbps, 384Kbps, 512Kbps, 768Kbps, 1Mbps, 1.5 Mbps, 2 Mbps, 3 Mbps, 4 Mbps, 5 Mbps, and 6 Mbps.
F7110 / F7115 User Manual Viewer authentication: On: If the viewer authentication is On, the users will be requested to key-in username and password when using QuickTime Player…etc. to have live viewing. Off: If the viewer authentication is Off, you can have live viewing on computer by QuickTime Player…etc. after entering “rtsp://ip:port/video.mp4” on the URL column directly. Multicasting streaming (if it’s on): Multicast Address: Specify the multicast server address.
F7110 / F7115 User Manual value to solve the problem. Note: If Video clip format of General Menu, which is for recording compression, is chosen MPEG-4, the IP interval option will appear “Auto” automatically and can’t select. The limit is for avoiding damaging the recording quality of 5 seconds temporary-saved video recorded on FTP server. 8.2.
F7110 / F7115 User Manual 10, 15, 20, 25, and 30 fps. The unit “fps” stands for “frames per second”. Note: The frame rate is up to 15 fps at 1280x1024, and up to 30 fps at 640x480. However, if you would like choose frame rate over 15 fps, the IMAGE SIZE of H.264/MPEG-4/MJPEG setting page has to been selected 320x240 or 640x480 at the same time. Quality: Auto: The quality and bit rate will be adjusted automatically according to the frame rate.
F7110 / F7115 User Manual unit “fps” stands for “frames per second.” Quality: Auto: The quality and bit rate will be adjusted automatically according to the frame rate. Fixed Quality: This item here can’t be selected. Fixed Bitrate: Set the bitrate of 3GPP image transmission for a line. You can select one among 64Kbps, 128Kbps, 256Kbps, 384Kbps, 512Kbps, 768Kbps, 1Mbps, 1.5 Mbps, 2 Mbps, 3 Mbps, 4 Mbps, 5 Mbps, and 6 Mbps. IP interval: It’s the ratio of i-frame & p-frame.
F7110 / F7115 User Manual Exposure mode: Choose Auto or Manual upon the capture environment. Auto: Choose Auto and you have 3 options to adjust the exposure condition. Back Light Compensate: Click it on and it helps avoid problems in situations where the main subject ends up being too dark, such as when shooting people or other subjects in front of a bright background. Slow Shutter: Click it on and the range of shutter speed will be from 1/5 to 1/120 sec.
F7110 / F7115 User Manual 8.2.7 PLAYBACK Clicking the button of “Open files” and select the video file recorded previous, you can look for the desired image. Besides, you can still have the live view in the screen.
F7110 / F7115 User Manual 8.3 Network Click the folder of Network to display the sub folders including Information, PPPoE, DDNS, UPnP, Bonjour, IP Notification, Wireless and Messenger. 8.3.1 Information Display the MAC address of the device. Obtain an IP address automatically (DHCP): If a DHCP server is installed on the network, to select this while the IP address is assigned by the DHCP server. Obtain DNS server address automatically: Select this to obtain the address of DNS server automatically.
F7110 / F7115 User Manual Use the following IP address: Select this option when the fixed IP address is set. IP address: Enter the IP address of the device. Subnet mask: Enter the subnet mask. Default gateway: Enter the default gateway. Use the following DNS server address: Select this when you set the fixed address as the IP address of DNS server. Primary DNS server: Enter the IP address of the primary DNS server.
F7110 / F7115 User Manual IP address: The IP address obtained at the PPPoE connecting with network. User ID: Enter the user ID for authentication necessary for PPPoE connections. Type it up to 64 characters. Password: Enter the password for authentication necessary for PPPoE connections. Type it up to 32 characters. Re-type password: Re-type the password to confirm. Obtain DNS server address automatically: Select this to obtain the address of DNS server automatically.
F7110 / F7115 User Manual 8.3.3 DDNS (Dynamic DNS) DDNS is a system which allows the domain name data held in a name server to be updated in real time. The most common use for DDNS is allowing an internet domain name to be assigned to a computer with a varying / dynamic IP Address. This makes it possible for other sites on the internet to establish connection to the machine without needing to track the IP Address themselves. Server name: Choose the DDNS Server from the list.
F7110 / F7115 User Manual Note : How to apply DDNS username and Host name?? You can apply DDNS username and Host name by the following steps: 1. Login http://www.dyndns.org, click the Creat Account 2.
F7110 / F7115 User Manual 3. Login with new account and click Account → My Hosts → Add Host Services 4.
F7110 / F7115 User Manual 5. After type information, check your DDNS service. 6. Type your DDNS User ID, Password and Host name in Setting → Network → DDNS. After completing setting, reboot IP Camera.
F7110 / F7115 User Manual 8.3.4 UPnP (Universal Plug and Play) If you have a Router to access to internet and the Router supports UPnP IGD function, you need to turn on the UPnP Port Forwarding function. HTTP port: Enter the HTTP port number and default HTTP port is 80. SSL port: Enter the SSL port number and default SSL port is 443. RTSP port: Enter the RTSP port, default value is 554 for computer view. Note : UPnP (Universal Plug and Play): UPnP is a set of computer network protocol.
F7110 / F7115 User Manual 8.3.5 Bonjour Bonjour, also known as zero-configuration networking, enables automatic discovery of computers, devices, and services on IP networks. Bonjour uses industry standard IP protocols to allow devices to automatically discover each other without the need to enter IP addresses or configure DNS servers. Device Name: Enter Device Name you wish. Note: How to use Bonjour in your Windows Browser UI? Please check the link below: http://www.apple.
F7110 / F7115 User Manual 8.3.6 IP Notification When network notify type is set to “ON”, you can send an e-mail notification of the completion of the network setting. Notify Type: You can select the notify type among DHCP, Static IP, and PPPoE. SMTP Server Name: Type the SMTP server name up to 64 characters, or the IP address of the SMTP server. SMTP Server Port: You can set port number from 1~65535 according to your mail server. The default value is 25.
F7110 / F7115 User Manual User name, Password: Type the user name and Password of the user who has the mail account. This setting is necessary when the SMTP server which sends e-mails performs authentication. Recipient e-mail address: Type the recipient e-Mail address up to 64 characters. You can specify up to three recipient E-mail addresses. Administrator e-mail address: Type the Administrator e-Mail address up to 64 characters.
F7110 / F7115 User Manual Status of Wireless Network This list is the result of network scan. The network is currently linked to will be shown in blue. The following information is provided. ESSID - The name of a wireless network (or ad-hoc device). If the same name occurs several times this means that several access points for that network were found. The camera cannot be configured to only associate with one particular access point.
F7110 / F7115 User Manual administrator can select the key length among 64 or 128 bits. 64bits is the default setting. 8.3.8 WPS WPS (Wi-Fi Protected Setup) also known as a standard for easy and secure establishment of a wireless home network. Status of WPS This list is the result of network scan that only provide wireless AP with WPS function. The network is currently linked to will be shown in blue. Configuration Method PBC – Select and click Start to start WPS configuration.
F7110 / F7115 User Manual 8.3.9 Messenger Messenger function provide an easy-connect feature. User can easy to know what camera’s private and public IP address is. Protocol: support MSN only. Login Account: Camera will use this account to login MSN server. This MSN account should be applied form http://www.msn.com. Password: password for this msn account. Re-type password: re-type password to double confirm. Alias: This alias will display on MSN like the following which display in red frame.
F7110 / F7115 User Manual Video Mode: You can choose to receive video streaming from Computer view (MPEG-4) or Mobile view (3GPP). IP Notification: Switch the IP notification On / Off. If this feature switches On, camera will send IP notification to the users who are allowed. Privacy: Switch privacy On / Off. When privacy turns on, only those users in allow list can access the camera. User: Input to this blank to edit allow list.
F7110 / F7115 User Manual 8.4 Security Click the folder of Security to display the sub folders including Account and HTTPS. 8.4.1 Account The device fault account and password setting is “admin / admin”. That means everyone who knows IP address can access the device including all configuration. It is necessary to assign a password if the device is intended to be accessed by others. User name: Set a user name between 4-16 characters. Password: Set a password between 4-16 characters.
F7110 / F7115 User Manual 8.4.2 HTTPS HTTPS is a URL scheme used to indicate a secure HTTP connection. It is syntactically identical to the http:// scheme normally used for accessing resources using HTTP. Using an https: //URL/ with a different default TCP port (443) and an additional encryption / authentication layer between the HTTP and TCP. You can use the IP camera through HTTPS easily by using https:// instead of http://. Create & Install: Create a self-signed certificate for HTTPS to recognize.
F7110 / F7115 User Manual 8.4.3 IP Filter IP Filter provides the function of controlling the range of IP address, similar with firewall service. IP filter: Select if you would like to have IP filter function. Allow range: The default range is from 0.0.0.0 to 255.255.255.255. Enter the “Start IP address” and “End IP address” in the range, then you can add a new allow range in allow range list. Allow range list: Except the default range 0.0.0.0~255.255.255.
Chapter 9. Setting-Advanced F7110 / F7115 User Manual Click the folder of Advanced to display the sub folders including PTZ control, Preset position, Patrol, FTP client, SMTP, Network storage, HTTP event, Alarm output, Schedule, Alarm input, Alarm buffer, Motion detection, Audio detection, and System Log. 9.1 PTZ Control In this section, it provides Pan, Tilt, Auto Pan speed control setting. 9.1.1 Setting Pan Speed: Use it to move bar from 0 to 100. Tilt Speed: Use it to move bar from 0 to 100.
F7110 / F7115 User Manual 9.2 Preset Position In this section, up to 32 Pan and Tilt positions can be saved, as well as the home position, which the device faces to when the power is turned on. 9.2.1 Setting Set: Use it to save the camera position to a preset number. Carry out the following steps. Move the camera to the position to be saved while you are checking the image with the main console. Write the preset position name in Preset Pos. Name text box. Click the SET.
F7110 / F7115 User Manual Delete: Select a preset number from 1 to 32 in the list box. Use it to delete specific number preset position setting. 9.2.2 Alarm Sending Alarm Motion detection: Click it on for using Motion detection function as a sensor. You can set motion detection function at the motion detection function screen. Note: You can set motion detection at motion detection screen. (Please go “Setting → Advanced →Motion detection → Setting”) For more details, you can check Chapter 9.12.
F7110 / F7115 User Manual Note: You can set alarm buffer at alarm buffer screen. (Please go “Setting → Advanced → Alarm buffer → Setting”) Alarm For more details, you can check Chapter 9.11. Input: Select the connected alarm. Sensor input1: The external sensor which is connected to sensor input1 of the alarm input. Note: You can set the alarm input function at alarm input screen. (Please go “Setting → Advanced → Alarm input → Setting”). For more details, you can check Chapter 9.10.
F7110 / F7115 User Manual 9.3 Patrol There are four patrol tours to set for composing different preset positions. Each one lists up to 8 positions which can be programmed, and the camera moves to the programmed positions sequentially. The camera stops when it moves to the last preset position. Tour name: Rename the tour name. Tour position Order: There are 8 orders to select for camera directions. Select Pos.: There are up to 32 preset positions to choose for each order.
F7110 / F7115 User Manual 9.4 FTP Client Use this menu to set up for capturing and sending a image or video clip to an FTP server. By using FTP client function, you can send files which has been shot and recorded linked with the external sensor input or with the built-in motion detection function to FTP server. FTP client setting menu is composed of two tabs, General, Alarm sending and Periodical sending. 9.4.1 General Select On when you use FTP function. The FTP client Setting screen appears.
F7110 / F7115 User Manual Attached file type: You can choose snapshot or video clip for alarm sending. Select “Snapshot,” one snapshot will be transmitted to the specified FTP server while motion detection / audio detection / alarm input triggered. Select “Video clip,” one 5-seconds video clip will be transmitted. Test: After setting the FTP server information, you can tick the test key to test if the connection between IP CAM and FTP server works. 9.4.
F7110 / F7115 User Manual Sequence number: A consecutive number of 10 digits between 0000000001 and 4294967295 and two fixed digits 00 is added to the Image file name. Sequence number clear: Click Clear and the suffix of the sequence number returns to 1. Alarm Motion detection: Click it on for using Motion detection function as a sensor. You can set motion detection function at the motion detection function screen. Note: You can set motion detection at motion detection screen.
F7110 / F7115 User Manual 9.4.3 Periodical sending Select On, you can set to send an image file to FTP server periodically. Remote path: Remote path: Type the path to storage location of FTP server which you have authorized. Image file name: Type the file name of snapshot or video clip sent by SMTP up to 10 alphanumeric characters, - (hyphen) and _ (under score). Suffix: Select a suffix to be added to the file name sent by SMTP. None: The name of the sent file will be the Image file name.
F7110 / F7115 User Manual 9.5 SMTP Set the SMTP menu when you want to send an image or video clip via e-mail. By using Mail (SMTP) function, you can send a mail with attached file which has been shot linked with the external sensor input or with the built-in motion detection function. The file can also be sent periodically. E-Mail (SMTP) setting menu is composed of three tabs, General, Alarm sending and Periodical sending. 9.5.1 General Select On when you use the SMTP function.
F7110 / F7115 User Manual Note: If you use g-mail as your mail server, you should set 25 as your port number and tick SSL box. Authentication: Select the authentication required when you send an email. Off: Select if no authentication is necessary when an email is sent. On: When authentication is necessary an e-mail is sent, select one of the authentication methods from the followings. SMTP: Select if SMTP authentication is necessary when an e-mail is sent.
F7110 / F7115 User Manual 9.5.2 Alarm sending Set to send the mail with connection to the alarm detection by the external sensor input or by the built-in motion detection function. Select On to send the image file to SMTP server linked with the alarm detection. Alarm sending: Select On to set to send mail with connection to the alarm detection. File attachment: Set whether an image file is attached to the mail sent or not. When On is selected, the image file made by the settings below is attached.
F7110 / F7115 User Manual Alarm Motion Detection: Click it on for using Motion Detection function as a sensor. You can set motion detection function at the motion detection function screen. Note: You can set motion detection at motion detection screen. (Please go “Setting → Advanced → Motion detection → Setting”) For more details, you can check Chapter 9.12. Audio detection: Click it on for using Audio detection function as a sensor.
F7110 / F7115 User Manual 9.5.3 Periodical sending You can set to send an image file by SMTP server periodically by selecting On to send the image file by SMTP server linked with setting period. Image file name: Type the file name of the image sent by SMTP up to 10 alphanumeric characters, - (hyphen) and _ (under score). Suffix: Select a suffix to be added to the file name sent by SMTP. Date & time: The date & time suffix is added to the Image file name.
F7110 / F7115 User Manual 9.6 Network storage Network storage provides the storage function for saving image files to the specified computer and folder connected with the operating computer. 9.6.1 General Select On if you would like to use the network storage function. Then choose one protocol between Windows network (SMB/CIFS) and Unix network (NFS). Protocol - Windows network (SMB/CIFS):. Network storage location: Type the IP or name of specified computer and folder.
F7110 / F7115 User Manual Protocol- Unix network (NFS): Network storage location: Type the IP or name of specified computer and folder. For example, \\IP/folder name or \\ my_nas:\folder name. Test: After setting the network storage location information, you can tick the test key to test if the connection between IP CAM and network storage location works. Note: If the recording video file is assigned to be stored in a low-speed device (ex.
F7110 / F7115 User Manual Alarm sending: Select On to set to send mail with connection to the alarm detection. Image file name: Type the file name you want to assign to the file to attach a mail. You can use up to 10 alphanumeric, - (hyphen) and _ (underscore) for naming. Suffix: Select a suffix to add to the file name Date & time: The date & time suffix is added to the Image file name.
F7110 / F7115 User Manual 9.6.3 Periodical recording You can set up to transmit image files to the network storage location periodically by selecting On. Image file name: Type the file name you want to assign to the file transmitted to the network storage location. You can use up to 10 alphanumeric, - (hyphen) and _ (underscore) for naming. Suffix: Select a suffix to add to the file name Date & time: The date & time suffix is added to the Image file name.
F7110 / F7115 User Manual 9.7 Memory Card Memory card provides local storage function for saving image files to the specified SD/SDHC card in your camera. This function can be enabled only when you insert SD/SDHC card to the camera and the SD/SDHC card works well. 9.7.1 General Select On if you would like to use the memory card function. Then click Execute to format your SD/SDHC card or click OK to enable memory card function directly. Card Status: Show the space free/total size of your memory card.
F7110 / F7115 User Manual Authentication: Select the authentication required when you send an email. Off: Select if no authentication is necessary when an email is sent. On: When authentication is necessary an e-mail is sent, select one of the authentication methods from the followings. SMTP: Select if SMTP authentication is necessary when an e-mail is sent. POP before SMTP: Select when POP before SMTP authentication is necessary when an e-mail is sent.
F7110 / F7115 User Manual 9.7.2 Alarm sending Set to transmit the snapshot or video clip file with connection to the alarm detection by the external sensor input or by the built-in motion detection function. Select On to send the file to network storage location linked with the alarm detection. Alarm sending: Select On to set to send mail with connection to the alarm detection. Image file name: Type the file name you want to assign to the file to attach a mail.
F7110 / F7115 User Manual Note: You can set audio detection at audio detection screen. (Please go “Setting → Advanced →Audio detection → Setting”) Network For more details, you can check Chapter 9.13. Link Down: Click it on to receive a video clip while network link down. It’s for recording video file in the IP CAM before and after disconnected network. Note: You can set alarm buffer at alarm buffer screen.
F7110 / F7115 User Manual Date & time: The date & time suffix is added to the Image file name. The date & time suffix consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits), minute (2 digits) and second (2 digits), and consecutive number (2 digits), thus 14-digit number is added to the file name. Sequence number: A consecutive number is added to the Image file name. Sequence number clear: Click Clear and the suffix of the sequence number returns to 1.
F7110 / F7115 User Manual 9.8 HTTP Event Set up this menu for sending commands to an HTTP server. By using HTTP client function, you can send the command defined by yourself, linked with the external sensor input or with the built-in motion detection function to HTTP server. HTTP client setting menu is composed of two tabs, General and Alarm sending. 9.7.1 General HTTP event: Set up the HTTP server URL, port, User ID, Password, and Proxy server settings. For example: URL: 192.168.1.
F7110 / F7115 User Manual 9.7.2 Alarm sending Set to send the command with connection to the alarm detection by the external sensor input or by the built-in motion detection function. Select “On“ to send the image and audio file to HTTP server linked with the alarm detection. Alarm sending: Select On to set to send command with connection to the alarm detection. Alarm Motion Detection: Click it on for using Motion Detection function as a sensor.
F7110 / F7115 User Manual Parameter: the parameter of CGI (defined in URL of HTTP → General) is from your target device. For example, move=down. Message: message will show up in the form of Message = PTZ down. If your target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ down. Audio Detection: Click it on for using Audio detection function as a sensor.
F7110 / F7115 User Manual Parameter: the parameter of CGI (defined in URL of HTTP → General) is from your target device. For example, move=down. Message: message will show up in the form of Message = PTZ down. If your target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ down. Alarm Input: Select the connected alarm. Sensor input 1: The external sensor which is connected to sensor input1 of the alarm input.
F7110 / F7115 User Manual Message: message will show up in the form of Message = PTZ down. If your target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ down. Effective Period: Set the period when the periodical sending is effective. Always: The periodical sending is always effective. Schedule: You can specify the period when the periodical sending is effective in the schedule setting in the other section.
F7110 / F7115 User Manual 9.8 Alarm Output You can set Alarm Output function in this menu to control the alarm out of I / O port on the rear of the device linked to the alarm detection and the timer. Alarm Output: To activate Alarm output 1/2 function, select On. If not, select Off. Digital Output: Select High signal output and Low signal output as your alarm. Trigger Condition: Select the mode of the Alarm output function. You can choose “Alarm” or “Timer”.
F7110 / F7115 User Manual Note: You can set the alarm input function at alarm input screen. (Please go “Setting → Advanced → Alarm Input → Setting”) For more details, you can check Chapter 9.10. Alarm Duration: There are up to 60 second options to choose for alarm duration interval. Effective Period: Set the period when the periodical sending is effective. Always: The periodical sending is always effective.
F7110 / F7115 User Manual 9.9 Schedule Click Schedule on the Advanced mode menu, the Schedule setting menu appears. This is the same menu as the setting menu which is displayed when you click Schedule to set Effective period and Schedule in FTP client, e-Mail (SMTP), HTTP event, Record, and Alarm out setting menu setting menu. Schedule Selection: Select the list box to specify the schedule you want to set.
F7110 / F7115 User Manual 9.10 Alarm Input When you click Alarm Input on the Advanced mode menu, the Alarm Input setting menu appears. You can set in this menu to control the external alarm input of I / O port on the rear of the device linked to FTP, SMTP, HTTP Sending Function, Network Storage and Memory Card. Alarm Input 1/2: Click it on for using external sensor which is connected to sensor input1 of the camera I / O port.
F7110 / F7115 User Manual 9.11 Alarm Buffer When you click Alarm Buffer on the Advanced mode menu, the Alarm buffer setting menu appears. You can set in this menu to enable alarm buffer function connected with FTP Client, SMTP, Network Storage, Memory Card, HTTP Event, Alarm Output and so on. Click it on to use alarm buffer function for recording audio and video file in the of IP Camera before and after disconnected network.
F7110 / F7115 User Manual 9.12 Motion Detection There are three Motion Detection functions as sensors to set for different detecting zones. Each one has Threshold and Sensitivity inputs which you can adjust to specific zone sequentially. Motion Detection function can support to FTP Client, SMTP, Network Storage, Memory Card, HTTP Event, Alarm Output and so on. Threshold: It means the extent which the alarm will be triggered. The default value is 50 and the value range is 0~100.
F7110 / F7115 User Manual 9.13 Audio Detection The Audio detection has Threshold and Sensitivity inputs which you can adjust sequentially. Audio Detection function can support to FTP Client, SMTP, Network Storage, Memory Card, HTTP Event, Alarm Output and so on. Click it on for using Audio Detection function as a sensor. You can set audio detection function at the audio detection function screen. Threshold: It means the extent which the alarm will be triggered.
F7110 / F7115 User Manual 9.14 System Log The System Log function allows users to review any changes and events happened. The system starts logging automatically after started. Enable Remote Log: Enables user to send the log data to a specified log server.
F7110 / F7115 User Manual CHAPTER 10. APPENDIX A. Frame-rate and Bitrate Table – Help to set IPCamera with your network environment to access Internet. Base on your network upload environment to choose the suitable Image-Quality setting. For example, if the network environment is ADSL 256Kb(upload) / 2Mb(download), the most fluent Image-Quality needs to set up under 256 Kb situation. A.1 Mega Mode A.1.1. H.
F7110 / F7115 User Manual 640*480 640*480 640*480 640*480 640*480 640*480 320*240 320*240 320*240 320*240 320*240 320*240 6144 6144 2048 2048 512 512 6144 6144 2048 2048 512 512 15 10 15 10 15 10 15 10 15 10 15 10 6300 6300 2200 2200 550 550 5100 3600 2200 2200 550 550 15 10 15 10 15 15 15 10 15 10 15 10 A.1.4. MPEG 4@ 15fps / kbps Quality 1280*1024 Excellent 2700 Detailed 1100 Good 500 Standard 350 Medium 300 1280*720 2000 800 350 250 200 640*480 300 200 150 100 80 320*240 100 80 60 40 35 A.1.5.
F7110 / F7115 User Manual 640*480 640*480 320*240 320*240 320*240 320*240 320*240 320*240 512 512 6144 6144 2048 2048 512 512 15 10 15 10 15 10 15 10 550 550 2200 1800 2200 1800 550 550 15 10 15 10 15 10 15 10 A.1.7. MJPEG @ 15fps / kbps Quality 1280*1024 Excellent 22000 Detailed 12000 Good 7000 Standard 5500 Medium 4000 1280*720 16000 7000 5000 4000 3000 640*480 6000 3000 2500 2000 1200 320*240 2200 1200 1000 800 500 A.1.8.
F7110 / F7115 User Manual 320*240 320*240 320*240 320*240 Good Good Medium Medium 15 10 15 10 1000 700 500 350 15 10 15 10 A.2 VGA Mode A.2.1 H.264 @ 30fps / kbps Quality Excellent Detailed Good Standard Medium 640*480 600 120 60 50 40 320*240 60 40 30 25 20 A.2.2 H.264@15 fps / kbps Quality Excellent Detailed Good Standard Medium 640*480 400 80 40 30 25 320*240 40 30 25 20 15 A.2.3 H.
F7110 / F7115 User Manual A.2.5 MPEG4@ 15fps / kbps Quality Excellent Detailed Good Standard Medium 640*480 600 250 150 100 80 320*240 80 50 40 30 20 A.2.
F7110 / F7115 User Manual 640*480 640*480 320*240 320*240 320*240 320*240 320*240 320*240 Medium Medium Excellent Excellent Good Good Medium Medium 30 15 30 15 30 15 30 15 95 2500 1400 4500 2500 2000 1200 1000 700 30 15 30 15 30 15 30 15
F7110 / F7115 User Manual B. Storage Requirement Table - Help to set Recording Storage System. Please refer to the following table to find out the capability for recording into your hard disk. B.1 Mega Mode B.1.1 H.264 Storage Requirement GB / channel / day @ 15fps Quality 1280*1024 1280*720 640*480 Excellent 15 12 1.8 Detailed 4 2.5 1 Good 2.5 1 0.8 Standard 1 0.6 0.5 Medium 0.8 0.5 0.4 320*240 0.5 0.3 0.2 0.15 0.1 B.1.2 H.
F7110 / F7115 User Manual 320*240 320*240 320*240 320*240 2048 2048 512 512 15 10 15 10 22 22 5.5 5.5 B.1.4 MPEG4 Storage Requirement GB / channel / day @ 15fps Quality 1280*1024 1280*720 640*480 Excellent 27 20 3 Detailed 11 8 2 Good 5 3.5 1.5 Standard 3.5 2.5 1 Medium 3 2 0.8 320*240 1 0.8 0.6 0.4 0.35 B.1.5 MPEG4 Storage Requirement GB / channel / day @ 10fps Quality 1280*1024 1280*720 640*480 Excellent 18 14 2 Detailed 8 5.5 1.2 Good 3.5 2.5 1 Standard 2.5 1.8 0.8 Medium 2 1.4 0.6 320*240 0.8 0.
F7110 / F7115 User Manual B.2 VGA Mode B.2.1. H.264 Storage Requirement GB / channel / day @ 30fps Quality 640*480 Excellent 2.5 Detailed 1.2 Good 0.6 Standard 0.5 Medium 0.4 320*240 0.6 0.4 0.3 0.25 0.2 B.2.2. H.264 Storage Requirement GB / channel / day @ 15fps Quality 640*480 Excellent 1.5 Detailed 0.8 Good 0.4 Standard 0.3 Medium 0.25 320*240 0.4 0.3 0.25 0.2 0.15 B.2.3. H.
F7110 / F7115 User Manual Medium 0.8 B.2.6. MJPEG Storage Requirement GB / channel / day Frame-Rate Image-Size Bitrate Setting Setting 640*480 6144 30 640*480 6144 15 640*480 2048 30 640*480 2048 15 640*480 512 30 640*480 512 15 320*240 6144 30 320*240 6144 15 320*240 2048 30 320*240 2048 15 320*240 512 30 320*240 512 15 99 0.2 Current Bitrate 6300 6300 2200 2200 550 550 5100 2800 2200 2200 550 550 Storage Requirement 63 63 22 22 5.5 5.5 51 28 22 22 5.5 5.
F7110 / F7115 User Manual C. System Requirement – Help to setup System C.1. 16 Channel IPCamera with CIF Performance Equipment Configuration Software: MainConsole Version 2.6.
F7110 / F7115 User Manual Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: Clause EN 60950-1: 2001 EN 50392: 2004 EN 300 328 V1.6.1 (2004-11) EN 301 489-17 V1.2.1 (2002-08) and EN 301 489-1 V1.5.
F7110 / F7115 User Manual English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
F7110 / F7115 User Manual Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
