86085H9000000
Zavio D3100/D3200 Quick Installation Guide Please follow the installation steps below to set up D3100 / D3200 Fixed Dome IP Camera. Check the package contents against the list below. See P.1 Physical overview. See P.2 I/O Terminal Block Circuit. See P.3 I/O Terminal Block Pin Definition. See P.3 LED Indicator Definition. See P.4 Power mode. See P.4 Install the hardware and connect all cables. See P.4 Microsoft OS: Use the software CD to install Intelligent IP Installer. See P.
Physical overview Built-in Microphone Slide cover Top cover Dome bubble Routing hole Leave the slide cover if you would like to plug in cables through the side of top cover and through a hole on the ceiling or wall.
I/O Terminal Block Circuit I/O Terminal Block Pin Definition This Camera provides a external I/O terminal block which is used to connect input/ output devices. The pin definitions are described below. PIN Definition 1 Ground - 2 + 5V DC 5V DC 0.5W 3 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block - 4 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block - Uses an NPN transistor with the emitter connected to the GND Digital Output 1 pin.
LED Indicator Definition LED Color Indication Network Blue Flash blue while Network activity. Red Steady red for booting up process; Steady red 30 Seconds when WPS configure failed. Blue Steady blue for booting up completion Purple Flash purple during firmware upgrading; when reset button pressed for at least 5 sec. to factory default Unlit When you press reset button; or Power off Power Power Mode PoE Mode Power Requirement PoE (IEEE802.3af) with Class 3 Power Consumption D3100: 2.
b. Wall mounting and Ceiling mounting 1) Attached the drill template to the wall. Drill three holes into the wall, which two for screws and one for cable (if you want to route cables through conduit hole). Then hammer the supplied plastic anchors into the screw holes and secure the plate with supplied screws. 2) Align the three holes on the base of camera with the two plastic anchors on the wall or ceiling, insert the supplied screws to the corresponding hole and screw them.
c. Lens focus range Rotate 360° Tilt 79° Rotate Notice: DO NOT rotate the lens over 2 rounds. Doing so will damage the camera lens module. Pan 344° d. Completion The camera has only Power over Ethernet (PoE) built-in. (there is no DC connector inside.) 1. Using a standard RJ-45 network cable, connect the IP Camera to a PoE-enabled Hub / Switch / Router. Note: If using a non-PoE switch, please use a PoE power injector to connect the camera.
e. Connect cables and power supply 1) Clean the dome bubble to remove the dust and finger print. 2) Align the slide cover down to the U-shape position. 3) Tighten the dome cover to the clockwise direction and make slide cover reaching the routing hole. Microsoft OS:Use the software CD to install Intelligent IP Installer Power on your PC and insert the CD-ROM. The setup page will show up automatically. Please follow these steps to install the firmware.
2. Click the Intelligent IP Installer Icon on your desktop. The main page will show up listing all active camera and video server devices. Select the relevant IP camera from the list and click Link to IE. 2 3. Enter your Username and Password to login to the IP Camera. (Default is admin / admin) 4. When accessing the IP Camera for the first time, a yellow information bar appears below the address bar: This website wants to install the following add-on: ‘AxvideoView.cab from ‘Zavio Inc’. 5.
7. Live video displays in the centre of your web browser. Mac OS using Safari Browser 1. Select Safari icon 2. Click Bonjour function and select the camera you wish to access. 3. Enter name and password to login to the IP 4. The monitor image will be displayed in your browser. camera.
Lighting environment setting The default setting of lighting environment is Auto. However, you may also select 50 or 60 Hz upon the lighting environment of your country. Go to “Setting > Live View > Camera Setting > Image Setting”, select the environment setting you wish. Change the Web Interface into your preferred language Use the settings screen to set the language of the Web Interface. Go to “System > Maintenance > Language”. 1. Insert Software CD into your CD-ROM. 2.
Application of IP Camera 11
12
