Z020 - EVDO Modem User Manual V5.7.0 2005.12.
Z020 EVDO Modem (User Manual) AnyDATA CDMA Module Series Reference Design Specification Copyright © 2005 AnyDATA Corp. All Rights Reserved. Any part of this document may not be distributed, communicated, reproduced or transmitted in any form or by any means, electronic or mechanical or otherwise, for any purpose, without the permission of AnyDATA Corp. This document can be subjected to revision without further notice. Contact Address AnyData.Net Inc.(Korea) DaeGo Bldg, 8 th.
Z020 EVDO Modem (User Manual) Contents 1. About Z020 USB MODEM.........................................................................................................................4 1.1 Product Description and Feature .....................................................................................................4 1.2 Technical Specification .....................................................................................................................5 2. Getting Started......................
Z020 EVDO Modem (User Manual) 1. About Z020 USB MODEM 1.1 Product Description and Feature In today’s fast-moving economy, the need to remain connected is essential. The world’s most compact Z020 EVDO USB modem, offers the appropriate solution to home and mobile connectivity using antenna diversity that enables better connectivity and data speed in poor signal environment and internal antenna technology. It provides extensive and reliable wireless data communication at speed up to 2.
Z020 EVDO Modem (User Manual) 1.2 Technical Specification Technical Standard RF Technology Electrical Input Power Interface Current Consumption Antenna Data Speed System Requirement Frequency Size Weight - CDMA EVDO - CDMA 1xRTT - TCP/IP and PPP - Antenna Diversity - Internal Antenna - Sensitivity : Lower than –104dBm - Transmit Power : 320mW(25dBm) max.
Z020 EVDO Modem (User Manual) 2. Getting Started In order to use Z020 USB MODEM following must be satisfied: 1) Zapp Internet Express Software and Z020 USB MODEM Driver has been installed on the computer. 2) The Z020 EVDO modem is active (the activation process has been successfully completed – this is indicated by POWER LED in green colour, and then by the restart of the modem). PLEASE CONNECT THE BATTERY AND EXTERNAL POWER SUPPLY TO INSURE MAXIMUM PERFORMANCE OF THE MODEM.
Z020 EVDO Modem (User Manual) EAR JACK +5V DC Mini POWER JACK USB Port Battery (optional) Zapp – The Next Generation Network 7/36
Z020 EVDO Modem (User Manual) External Antenna Port Battery Contact Pins When dismounting the battery, push the bottom of modem upward to slide easily out from the battery cradle. 2.1.1 LED indicator Information 1) POWER : - Blue : Use battery power only - Blink : Low battery warning - Red : Use external DC and not installed battery.
Z020 EVDO Modem (User Manual) 3) BUSY (Traffic) : - Blue : Data call connected - Green : General call connected., - Blink : Incoming call initiated and not answered yet. - Off : Not in connected state 4) SMS : - Yellow : Exists message in inbox - Blink : New message arrived in inbox - Off : Empty inbox 5) LEDs colors during activation process: - The POWER LED is blinking BLUE : The activation process is in progress. Please wait. - The POWER LED is RED : Activation process has failed.
Z020 EVDO Modem (User Manual) 3. Program Installation 3.1 Introduction This section describes step-by-step method to install Z020 USB MODEM and Zapp Internet Express Software. Note : Must install the software before connecting Z020 USB MODEM to PC/Notebook. 3.2 Minimum System Requirement 3.2.1 PC Hardware Recommend to use PC/Notebook at speed of 300 MHz or higher.
Z020 EVDO Modem (User Manual) 4) Welcoming message for using Zapp Internet Express Program window will appear. 5) Press button to proceed. 6) Next window is related to License Agreement. Please read carefully.
Z020 EVDO Modem (User Manual) 7) Next window displays asking proper path for installing the program. Default path is "C:\Program Files\Zapp Internet Express".
Z020 EVDO Modem (User Manual) 8) Press “Install” button to advance to the next step to install the program. 9) When program has been successfully installed, following window will display. 10) Press button for ending the program installation. If modem is not connected to PC/Notebook and device driver is not installed, then the program will not launch even after completion of installation program. 3.4 Connecting to Z020 USB MODEM and Driver Installation and Uninstallation. 3.4.
Z020 EVDO Modem (User Manual) 3) Press button to proceed. 4) A window that displays a proper path of Driver will appear. 5) Select from the CD’s path “[YourCDRomDirve]:\Driver\” folder for appropriate OS. 6) Press button to proceed. 7) A window that searches “AnyDATA CDMA USB Modem Device.
Z020 EVDO Modem (User Manual) 8) If found “AnyDATA CDMA USB Modem” it will ask for the installation. 9) Press button to move to the next step. 10) Process of installing “AnyDATA CDMA USB Modem” Driver.
Z020 EVDO Modem (User Manual) 11) If the installation of “AnyDATA CDMA USB Modem” has been completed, following window will appear. 12) Next, it will install “AnyDATA CDMA USB Serial Device” Driver.
Z020 EVDO Modem (User Manual) 13) Select “Install from a list or specific location (Advanced )”. 14) Press button to proceed. 15) Select the proper path from the CD window will appear. 16) Select from the CD’s path “CDRomDirve:\Driver\” folder for appropriate OS. 17) Press button to move to next step. 18) Window that searches “AnyDATA CDMA USB Serial Device” will appear.
Z020 EVDO Modem (User Manual) 19) When “AnyDATA CDMA USB Serial Device” has been found, it asks for the installation. 20) Press button to proceed.
Z020 EVDO Modem (User Manual) 21) If the installation has done properly, this window will appear. This will complete the driver installation. 3.4.2 Checking the proper installation of the Driver If the Driver has been installed properly, it is possible to check the proper operation from Control Panel. (the example below is for Windows XP) 1) Start Control Panel.
Z020 EVDO Modem (User Manual) 2) Select “Switch to Classic View.” 3) Select System.
Z020 EVDO Modem (User Manual) 4) Select “Device Manager” from Hardware Tab. 5) As shown in below with red boxed that shows “AnyDATA CDMA USB Modem” and “AnyDATA CDMA USB Serial Device,” the Driver has been successfully installed. Note: Please pay attention and write down the COM number in “AnyDATA CDMA USB Serial Device (PID 6501) “(COM8)”. In this case it was COM8, but it might be different for other installations.
Z020 EVDO Modem (User Manual) 3.4.3 Uninstallation When disconnecting USB cable from Z020 USB MODEM and the USB port, the diver will be automatically uninstalled.
Z020 EVDO Modem (User Manual) 4. Using Zapp Internet Express Program 4.1 Running the program There are 2 (two) ways to run the installed Zapp Internet Express program. As shown below, either pressing shortcut icon on the Desktop or pressing from the “Programs” list.
Z020 EVDO Modem (User Manual) 4.2 Exiting the program From the Zapp Internet Express program, by pressing button will quit the program. Note: If DUN is running or SMS is transferring, the program will end after the completion of these commands. 4.3 Screen Display of Zapp Internet Express 4.3.
Z020 EVDO Modem (User Manual) 4.3.
Z020 EVDO Modem (User Manual) 4.3.3 Description of each icon Display Function RSSI Signal Strength Indicator Calling Possible Calling not Possible New message arrived. Rx Diversity Mode. Supports Hybrid mode Only 1X mode available Only EVDO mode available Battery Indicator Battery Fully charged Using external power source USB connected Charging through USB Charge completed by USB Connected to the Modem Either the cable is disconnected to the modem or improper port connection.
Z020 EVDO Modem (User Manual) 4.3.4 Setting Environment There are 3 options and please refer to below for explanations. [ About ] Tab Display the software version for EV-DO modem S/W and Zapp Internet Express program.
Z020 EVDO Modem (User Manual) [ Basic ] Tab The basic configuration for connect to the network using EV-DO modem. All values are set automatically, however if wants to change the value then check appropriate box/boxes in the left and press button to take effect.
Z020 EVDO Modem (User Manual) [ Advance] Tab This part is used to change the important parameter for EV-DO modem. If you want to change the value then check appropriate box/boxes in the left and press button to take effect. Pref Mode: Place to select a mode from 1x only, EVDO only and EVDO + 1x. [Note] Basically the modem supports all modes if the network supports them.
Z020 EVDO Modem (User Manual) 4.3.5 Connecting to the Internet Connection information, such as UserName, Password, and ServiceNum, are already inserted into the Zapp Internet Express program. In case they are not inserted, you can manually type them: UserName and Password (not important for authentification), ServiceNum: #777. Then press button to connect to the internet. If the modem is trying to connect or connected to the Internet, this above.
Z020 EVDO Modem (User Manual) 4.3.7 Sending and Receiving calls This feature is not available with the Z020 modem in Zapp network. If you press button, the following pop-up message will appear: Note: Description of icons. 4.3.8 Viewing received or saved message (SMS can only be received when the modem is in 1x or Hybrid mode !) 1) By pressing “Inbox” icon, you will see a screen as below. 2) All received messages will be shown. 3) It will indicate whether the message was read or not.
Z020 EVDO Modem (User Manual) Unread message. Sent message. Note : Description of icons. 5. Troubleshooting Q: I cannot connect to the Internet? A: Please check “environment setting” of program for correct ID, password and Service number. For proper ID, password and Service number, please contact service provider for more information. Q: The Internet connection speed is too slow. A: Please check whether the modem is set at 1X mode.
Z020 EVDO Modem (User Manual) A: This means that USB modem and the computer are not connected properly. Please double check whether USB modem is connected properly to the computer. Q: During the running of the program, an error message appears and the program halts. A: The actual connection of USB modem and computer has been disconnected. Please check whether the cable is dismounted, cable is disconnected or USB modem power has been turned off. Then try to reconnect the modem.
Z020 EVDO Modem (User Manual)
Z020 EVDO Modem (User Manual) 6. Quick Guide 6.1 Display Indicators. The display may show the following icons to indicate the USB modem’s status or function. Display Function RSSI Signal Strength Indicator Calling Possible Calling not Possible New message arrived. Rx Diversity Mode.
Z020 EVDO Modem (User Manual) DECLARATION OF CONFORMITY We, SC TELEMOBIL SA, Romania, Baloteşti, j.
